• Proceedings of the Mineralogical Society of Korea Conference
• /
• 2001.06a
• /
• pp.44-44
• /
• 2001

구리(II)의 전자상자성공명 흉수선의 모양과 선 폭에 대한 해석을 통해 석영-물 계면에서의 구리(II) 및 흡착수와 석영 표면과의 상호 작용에 대해 연구하였다. 두 가지 흡수선이 중첩하여 흡수선을 구성하며 따라서 석영 표면에 적어도 두 종류의 구리(II)가 존재함을 알 수 있었다. 하나는 g=2.18에 중심을 둔 초미세 갈라짐이 분해되지 않는 등방성 단일 흡수선을 보여 주는 구리(II) 이온이다. 이는 수용액 중에서와 유사한 빠른 자유 회전 운동이 가능한 상태로 표면에 매우 약하게 결합된 구리 이온(Cu($H_2O$)$_{6}$$^{2+}$)인 것으로 해석된다. 다른 하나는 축 대칭 흡수선 $g_{∥}$=2.40, $g_{⊥}$=2.08)을 가지는 구리(II)로서 이는 표면에 강하게 결합된 것으로 해석된다. 본 결과는 흡착 현상에 대한 열역학적 접근법인 표면 착물화 모델들이 제시하는 광물 표면에서의 금속 이온 흡착 모델이 거시적 관점에서 흡착 현상을 잘 모사할지라도 분자 수준의 미시적 관점에서 흡착 메커니즘을 규명하기 위해서는 독립적인 분광학적 정보가 제시되어야함을 보여 준다.다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.10
• /
• pp.1019-1025
• /
• 1991

An analytic method of computation of the coupling coefficients between a microstripline and a die-lectric resonator is showen in this paper. The relationships among the substrate material, the ground plane, the diele-lents. The theoretically computed values of Qext are compared with the experimentally measured values of Qext in there is no dieletric spacer between them, As a result, the reflection coefficients with the dielectric spacer between the dieletric resonator and the substrate are decreased more than the reflection coefficients without the didlectric spacer between them.

• Korean Journal of Materials Research
• /
• v.11 no.1
• /
• pp.3-7
• /
• 2001

$M\"{o}ssbauer$ spectra of the $Ni_{1+x}Ti_xFe_{2-2x}O_4$ systems ($0{\leqq}x{\leqq}0.7$), which appear as single phase spinel structure, were examined at RT. The $M\"{o}ssbauer$ spectra reveal two sextet for $0{\leqq}x{\leqq}0.3$, two sextet and a doublet for $0.4{\leqq}x{\leqq}0.6$, and a doublet for x=0.7 As x increases, the area ratio of B-site and A-site($A_B/A_A$) of the sextet decreases, and the area ratio of the doublet and the total areas($A_{doublet}/A_{tot.}$) increases. The isomer shift(I.S.) of A-site slightly increases and magnetic hyperfine fields($H_{hf}$) of two sites decrease as the increasing x. From these results, we have obtained the cation distributions of the samples and concluded that the increasing x leads to the decrease of covalency of $Fe^{3+}-O^{2-}$ bond in A-sites and A-B superexchange interactions.eractions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.878-883
• /
• 2003

New feeding structures using linearly and exponentially tapered lines to planar microstrip resonators are proposed. These can overcome the design problems from coupling losses and impedance mismatching by increasing the coupling efficiency. The variation of its feeding angle is evaluated for the insertion loss and bandwidth and the feedline length is optimized at ${\lambda}_g$/2. The ring resonators and patches fed by the tapered line have been designed and implemented. The experimental results show that the insertion loss is enhanced by about 7 dB. Both rings and antennas are better matched, without disturbing the single-mode resonance or distorting their radiation pattern

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1981-1983
• /
• 2003

본 연구에서는 고속전력선통신(PLC)을 위한 고압배전선의 임피던스 측정 방법을 소개한다. 현재 전세계적으로 고속 PLC를 위해서 1MHz${\sim}$30MHz대역을 사용하고 있다. 임피던스 특성을 실제 필드에서 측정하기 위해 본 연구에서는 휴대용 고압결합장치를 개발하였다. 임의의 고압 배전선에 일시적으로 결합할 수 있도록 고안된 고압결합장치로서 살아있는 전력선에 정전 없이 설치 가능하다. 이 장치는 고압용 커풀러(Coupler)와 60Hz 저주파를 차단하기 위한 드레인 코일(drain coil)로 구성되었다. 측정을 위해서는 벡터 회로망 분석기를 사용하였으며, 본 논문에서는 측정된 고압선 임피던스를 보여 주고 이 결과를 이용한 임피던스 정합 방법을 제시하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.5
• /
• pp.516-524
• /
• 1997

The propagation properties of various pulse signal types(square pulse, Gaussian pulse, trapezoid pulse, RF pulse) on coupled microstrip lines are investigated. Numerical integration technique which has its accuracy and is easily simulated, is used to obtain the time domain response of pulse signals. Frequency-dependent characteristics of coupled microstrip line is obtained using Jansen's approximate equation. The propagation properties of pulse signal on coupled microstrip lines is analyzed regarding to its geometric structure (relative permittivity ${varepsilon}_r$ substrate height h, strip width w of the microstrip line) and pulse width ${\tau}$ of signal pulse. The simulation results show that space between two lines is very significant parameter in pulse distortion in comparison of any other parameters. The results of this paper are compatible to the trade-off determination of relative permittivity, substrate height, strip width and pulse width of signal pulse when a design of MIC and MMIC is necessary.

• Korean Journal of Optics and Photonics
• /
• v.17 no.3
• /
• pp.290-295
• /
• 2006

The coupling between copper wire and a THz electromagnetic wave is one of the important factors to build up the magnitude and spectrum of a THz wave. We measured a I THz spectrum range THz pulse into a $480{\mu}m$ diameter and 23cm long copper wire waveguide. We measured THz pulses up to $275{\mu}m$ air gap between the end of the copper wire and transmitter or receiver chips. The coupling sensitivity of the transmitter is 3 times bigger than that of the receiver. The THz pulses propagated to air by the end of the receiver-side copper wire tip acting as a transmitter antenna. We confirmed that the THz field concentrates near the copper wire surface by opening the pin hole to the copper wire waveguide.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.126-135
• /
• 2007

This paper proposes a new miniaturization method for a parallel coupled line filter with enhanced bandwidth characteristics. A previous method incorporated several advantages, such as size reduction through the use of only a small number of capacitors, in addition to grounding, suppression of harmonic characteristics, and improved skirt characteristics for the parallel coupled line filter, which is conventional in the field of RE filters due to its design and fabrication simplicity. However, the previous method also has disadvantages related to the bandwidth shrinkage of the miniaturized filters. In this paper, the amount of bandwidth shrinkage is analyzed in terms of the relationship between the loaded Q(quality factor) and the group delay of a resonator. Moreover, the reduction in the bandwidth is solved by a design with new design equations. To show the validity of the proposed method, a hairpin filter with a center frequency of 5.2 GHz and an fractional bandwidth(FBW) of 10% was scaled down to half its original dimension by the proposed method with the enhanced bandwidth characteristics. The measured result shows a high level of agreement with theoretical results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.4
• /
• pp.397-403
• /
• 2008

In this paper, the mixer was implemented in the non-radiative dielectric waveguide that is the main component of 60 GHz band radio telecommunications equipment which a demand increases for the purpose of point-to-point communication network. As to the manufacture of the non-radiative dielectric waveguide mixer, it was the implementation of the dielectric line combiner to be most difficult. The thing which that gives shape to the curvature which is the dielectric line determined and the to place in the exact interval thing are easy. For this reason, it was very difficult to make in order to have the regular performance in the case of the mixer having the dielectric line combiner. In this paper, since the dielectric line combiner was replaced with the waveguide directional coupler and the manufacture was possible through a processing it had the characteristic that a combiner is fixed. In result, the productivity of a mixer was innovatively improved. The design frequency of the mixer implemented through this paper RF and LO are $51{\sim}64\;GHz$. IF Is $DC{\sim}\;GHz2$. The down conversion loss toward the RF input of $60{\sim}62\;GHz$ was measured by $10{\pm}1\;dB$ in the condition that LO is 10 dBm, 60 GHz.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.347-351
• /
• 2003

본 논문에서는 전력 분배비를 변화시킬 수 있는 전력 분배기/합성기를 설계하였다. 전력 분배기/합성기의 ${\lambda}/4$ 전송선로 특성 임피던스를 결합선로 또는 하이브리드로 변환하여 설계하였다. 결합 선로나 하이브리드의 결합포트와 격리포트를 동시에 On/Off시킴으로써 변화하는 임피던스를 이용하여 전력 분배비가 1:1에서 1:0으로 즉 전력이 두개의 포트에 같은 크기로 전달되다가 모든 입력이 하나의 출력포트로 모두 전달되는 전력 분배기를 설계하였다.