• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.4
• /
• pp.36-43
• /
• 2017

We studied attenuation characteristics of shock waves induced by a donor charge and the sensitivity of an acceptor for optimal design of a TBI (Through-bulkhead initiator). The attenuation behavior of shock waves was studied by measuring free surface velocity using a VISAR (Velocity Interferometer System for Any Reflector), and the sensitivity of the acceptor explosives was analyzed via SSGT (Small Scale Gap Test). It was found that the acceptor sensitivity obtained by the SSGT may be inappropriate for the design of the small-scale explosive devices such as TBI due to the different shock duration time.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.2
• /
• pp.125-135
• /
• 2003

A 3-dimensional model of curved steel box girder bridges without diaphragm was presented. This model yielded results that were consistent with those of the parameter analysis using the BEF and Ritz methods. Se veralmodels with diaphragms were analyzed to estimate the appropriate diaphragm spacing. In case of 50m span, models A-10, A-20, A-30, B-10, B-20, and B-30 were found to have 5(8.3m), 7(6.25m), 8(5.5m), 4(10m), 6(7.1m), and 7(6.25m) diaphragms, respectively. In addition, a formula that presents the ratio of distortional stress to bending stresswas created from the results of the 3-dimensional FEM model analysis.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1114-1118
• /
• 1999

Barrier rib for the plasma display panel(PDP) was made by photolithographic process utilizing photosensitive barrier rib paste. The barrier rib paste was prepared by first dissolving ethylcellulose(binder polymer) in butyl carbitol(BC)/butyl carbitol acetate(BCA) =30/70 wt % mixture solvent at 15 wt % concentration. To this solution a mixture of functional monomers consisted of tripropyleneglycol diacrylate/ pentaerythritol triacrylate = 50/50 wt %, Irgacur 651 photoinitiator, and barrier rib powder were added and then the whole mixture was mixed in the three roll mill for 2 hr. The effect of component and concentration of photosensitive barrier paste on the photolithographic process was studied. After optimization of the paste formulation and photolithographic process, barrier rib could be obtained with good resolution up to $100{\mu}m$ height.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.6
• /
• pp.796-802
• /
• 2018

The effects of inner liquid sloshing on vessel motions are a well-known factor. It was investigated experimentally and numerically. In this regard, the study of many efforts to reduce natural phenomena of vessel motions by adopting special devices especially for roll motions. Among many devices, inserting baffles in the inner liquid tank is very common. In this study, one investigated the vessel motions with inner sloshing tanks with baffles inside. For the numerical simulation, one employed a dynamically coupled program between boundary-element-method-based vessel motion analysis program and a particle-based computational fluid dynamics program. Comparing corresponding experimental results validated the dynamically coupled program. The validated coupled program was used to simulate vessel motions, including sloshing effects with various lengths of inner baffles. The simulation results show that not only the filling ratio of inner liquid, but also the length of clearance due to baffles influenced the vessel motions. The significant point of this study was that the natural frequency of vessel motions can be maintained irrespective of the amount of filling ratio through adjustment of the clearance. In a future study, the effects of various numbers of baffles with various clearances would be conducted to percuss the possibility of vessel motion control with inner liquid sloshing effects.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5A
• /
• pp.841-848
• /
• 2006

There is a complex variation of stress in PSC anchorage zones and box girder diaphragms because of large concentrated load by prestress. According to the AASHTO LFRD design code, three-dimensional effects due to concentrated jacking loads shall be investigated using three-dimensional analysis procedures or may be approximated by considering separate submodels for two or more planes. In this case, the interaction of the submodels should be considered, and the model loads and results should be consistent. However, box girder diaphragms are 3-dimensional disturbed region which requires a fully three-dimensional model, and two-dimensional models are not satisfactory to model the flow of forces in diaphragms. In this study, the strengths of the prestressed box girder diaphragms are predicted using the 3-dimensional grid strut-tie model approach, which were tested to failure in University of Texas. According to the analysis results, the 3-dimensional strut-tie model approach can be possibly applied to the analysis and design of PSC box girder anchorage zones as a reasonable computer-aided approach with satisfied accuracy.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.2
• /
• pp.43-51
• /
• 2020

After the accelerated aging, the bulkhead initiator using high explosives was carried out to verify aging characteristics. The Thru-Bulkhead Initiator operates by transmitting shock-wave generated from micro-initiator to the acceptor and the ignition explosives through the bulkhead. In order to evaluate the life-time of the product, the accelerated aging condition was set according to the life-time, and the ignition performance of the sample was measured every 10 cycles by measuring the delay time and the maximum pressure through the 10cc closed bomb test. In addition, variance analysis was used to determine aging.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.30-31
• /
• 2009

전하가 다른 두 종류의 토너입자를 ITO 기판에 격벽 높이의 차이를 두어 제작한 패널을 사용하였다. 토너입자를 충전할 때 동일한 격벽 높이의 패널을 사용하는 것과 서로 다른 패널을 사용하여 합착, 2가지 type을 제작하였다. 제작된 패널을 전압별로 구동하고 각 구동전압에서의 광특성을 측정하였다. 셀 내부에 충전되어 있는 입자보다 운동량이 적은, 즉 셀 내부에서도 격벽 표면에 흡착되어 있는 토너입자들이 구동과 광특성에 어떠한 영향을 미치는지 평가하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.439-443
• /
• 2008

본 연구는 어도에서의 어류이동의 적합성을 검증하기 위해 어도 수리실험을 통해 흐름에 따른 어류이동을 조사하는 것으로 하였다. 이를 위해 실험은 모형이 아닌 거의 실물에 가까운 원형 수준의 어도를 제작하였다. 물고기는 피라미를 준비하였으며, 어도 내부에 넣고 흐름을 형성시켜 어류의 거동을 비디오로 촬영하였다. 어도 격벽은 두께를 t=0.1m, 어도 폭은 B=1.0m, 격벽간 거리는 L=$1.0{\sim}2.0m$, 격벽간 낙차는 ${\Delta}H=0.1m$로 하여 각 경우에 따른 실험을 실시하였다. 본 연구 결과에 따르면 어류 이동에 효율적인 흐름의 속도는 $1.0{\sim}1.5$(m/s)임을 나타내고 있는데, 이는 기존 피라미의 선호유속(0.8m/s)보다 높은 편으로서, 이는 어류의 상류이동을 위해서는 선호유속보다 약간 높은 유속을 형성시킴으로써 어류가 상류로 이동하려는 의욕을 가지게 하는 것이 중요함을 시사하였다. 상기 실험 결과를 바탕으로 어류(피라미)의 상류 이동에 적합한 계단식 어도는 경사가 1/20이고, 상하류 격벽 단차가 10cm 정도로서 순환류가 약하게 형성되며, 월류 흐름의 속도가 $1.0{\sim}1.5$(m/s)를 유지하는 형태임을 알 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.80-80
• /
• 1999

플라즈마 디스플레이 패널(PDP)의 공정을 간단히 하기 위하여 포토레지스트, ITO, 격벽재료를 Ar+ laser(λ-514 nm, CW)와 Nd:YAG laser(λ=532, 266nm, pulse)로 직접 패터닝 하였다. 레이저에 의한 포토레지스트의 패턴결과, 아르곤 이온 레이저의 포토레지스트 가공의 반응 메카니즘은 레이저 빔의 열에 의한 시료 표면의 국부적인 온도상승에 의한 용융작용이며, 그 결과 식각 후 형성된 패턴의 단면 모양도 레이저빔의 profile과 같은 가우시안 형태를 나타낸다. Nd:YAG 레이저의 4고조파(532nm)를 이용한 경우 200$\mu\textrm{m}$/sce의 주사속도에서 포토레지스트를 패턴하기 위한 임계에너지(threshold energy fluence) 값은 25J/cm2이며, 약 40J/cm2의 에너지 밀도에서 하부기판의 손상이 발생하기 시작하였다. 글미 1은 Nd:YAG 레이저 4고조파를 이용하여 포토레지스트를 식각한 경우 SEM 표면사진(위)과 단차특정기에 의한 단면형상(아래)이다. ITO 막의 레이저에 의한 직접 패턴 결과, ITO 막은 레이저 펄스에 의한 급속 가열 및 증발에 의한 메커니즘으로 식각이 이루어지며, 레이저 파장에 따른 광흡수 정도의 차이에 의해 2고조파 (532nm)에서 ITO 막의 가공 품질이 4고조파(266nm)에 비해 우수하며 패턴의 폭도 출력에 따라 제어가 용이하였다. 그림 2는 Nd:YAG 레이저 2고조파를 이용하여 ITO를 식각한 경우 SEM표면 사진(위)과 단차측정기에 의한 단면형상(아래)이다. 격벽 재료의 레이저에 의한 직접 패턴 결과, Ar+ 레이저(514nm)는 출력 밀도 32NW/cm2에서 격벽을 유리 기판의 경계면까지 식각하였다. Nd:YAG 레이저(532nm)는 laser fluence가 6.5mJ/cm2에서 격벽을 식각하기 시작하였으며, 19.5J/cm2에서 유리기판의 rudraus(격벽 두께 130$\mu\textrm{m}$)까지 식각하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.6
• /
• pp.2343-2350
• /
• 2013

The wave height distributions in front of a vertically perforated wall structures for obliquely incident uni-directional irregular waves are mainly investigated by using 3D hydraulic experiments. The difference and similarity of wave propagation along the plain and perforated wall structures are investigated and particularly the effects of side walls in chamber and relative chamber width are analyzed. This study shows that the wave height distribution patterns for normalized wave heights in front of structure is significantly different between the plain and perforated wall structures, and the side wall in the chamber suppresses the growth of waves.