• The Journal of Engineering Geology
• /
• v.17 no.2 s.52
• /
• pp.225-233
• /
• 2007

The engineering properties of surface soils in natural terrain are changed due to wildfire. This change of engineering properties induced by wildfire is related to landslides occurrence. To investigate the change of soil properties caused by wildfire, the various soil tests are performed. The soil samples are obtained from the recently burned slopes of Yangyang area, Kangwon Province. The soil samples obtained from the burned slopes are classified into three types depending on the burning grade: the perfect burning grade, the intermediate burning grade, the non-burning grade. As the result of tests, the specific gravity and the dry unit weight of soils obtained from perfect and alternative burning grades are less than those of soils obtained from non-burning grade. It judges that an electronic force, ionic components and of soils are changed and organic matters in soils are burned by wildfire. The permeability of soil obtained from alternative burning grade is the lowest and that of soil obtained from perfect burning grade is the highest. The water-repellent layer is formed on soil surface by wildfire. The water-repellent layer is existed at the area of alternative turning grade, while the layer is not existed at the area of perfect burning grade. The water-repellent layer is collapsed in high temperature more than about $400^{\circ}C$.

• Journal of the Korean earth science society
• /
• v.26 no.6
• /
• pp.597-602
• /
• 2005

The Late Quaternary palynoflora from an archaeological site in Piseo-ri, Muan, Korea consists predominately of deciduous broadleaved angiosperms and subordinately of herbs and conifers. Dominant taxa are Polypodiaceae, Taxodiaceae-Cupressaceae-Taxaceae, Alnus, Carpinus, deciduous Quercus, Compositae and Gramineae. The palynoflora dated 43,000-18,000 yr BP, corresponding to the last glacial period, is similar to the modern vegetation of the cool temperate deciduous broadleaved forest in the middle part of the Korean Peninsula. Based on palynofloral composition, three palynozones are recognized. Zone I represents a cool temperate deciduous broadleaved forest, composed of Polypodiaceae, Taxodiaceae-Cupressaceae-Taxaceae, Alnus and D. Quercus, and is characterized by persistent occurrence of warm temperate taxa. Zone II shows drastic decrease in Polypodiaceae, Taxodiaceae-Cupressaceae-Taxaceae, and increase in herbs. This zone reflects a cool temperate deciduous broadleaved forest with scattered open grasslands. Zone III is characterized by dominance in herbs and increase in conifers. The palynofloral composition suggests a cool temperate climate, and variation in occurrences of main taxa indicates that climatic conditions gradually became cold and dry.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.10a
• /
• pp.37-37
• /
• 1999

Cr-N 계 박막은 경도가 높고 치밀한 층을 형성할 수 있으므로 현재 금형과 기계류 핵심부품의 내마모 및 내식성 향상을 위한 대표적인 물질로 많은 주목을 받고 있다. 본 연구에서는 아크 이온플레이팅 장비를 이용하여 질소분압, 바이어스 전원 등의 변화에 따른 Cr-N계 박막의 결정성 및 표면상태, 증착율, 그리고 내마모성을 조사하였다. Cr-N 계 박막을 증착하기 위해서 사용한 시편은 $20MM{\phi}{\times}4mmt$ 크기의 고속도 공구강 디스크이었으며, Trichloroethylene에서 5분간 초음파 세척을 한 후 건조하여 진공용기 내에 장착하였다. 박막을 증착하기전 시편의 표면을 깨끗하게 하기 위해서 Ar 이온 충격으로 플라즈마 전처리를 하였다. 증착된 Cr-N 계 박막의 두께는 CALOTEST와 XRF 두께 측정기를 이용하여 측정하였으며, 박막의 결정성과 내마모성은 X-선 회절분석기와 tribometer로 관찰하였다. 아크 전류를 변화시키면서 증착한 Cr-N 박막의 경우 층작율은 아크 전류가 50A에서 80A로 증가함에 따라 45nm/min에서 87nm/min으로 증가하였다. 그리고 바이어스 펄스의 duty-on 시간과 주파수가 증가할수도록 박막의 증착율은 감소함을 알 수 있었다. Duty-on 시간과 주파수의 증가는 기판에 오랫동안 이온의 충격을 가하므로서 상대적으로 가벼운 질소이온이 크롬과 결합하는 것을 방해하여 박막의 증착율이 감소할 것이다. 기판에 인가하는 바이어스 펄스의 duty-on 시간을 변화시키면서 증착한 Cr-N 박막에 대한 X-선 회절상을 조사한 결과 duty-on 시간이 20%인 경우에는 Crn(111), CrN(200)와 Crn(220) 피크 들만 나타나 입방정의 CrN 박막이 형성되었으며, duty-on 시간의 증가에 따라 $Cr_2N$ 상의 형성이 점점 많아져 80% duty-on 시간 경우에는 거의 CrN과 $Cr_2N$ 상이 공존하는 것으로 나타났다. 또한 duty-on 시간이 증가할수록 회절피크의 세기가 증가하여 결정화가 더 많이 진행되어짐을 알 수 있었다. 마찬가지로 바이어스 펄스이 주파수에 다른 결정성의 변화도 펄스의 주파수가 증가할수록 박막이 결정성이 좋아지고 $Cr_2N$ 상이 쉽게 형성되었다. 증착 진공도에 따른 결정성은 상대적으로 질소의 농도가 높은 낮은 진공도에서는 CrN 상이 주로 형성되었으며, 반대로 높은 진공도에서는 $Cr_2N$ 상이 많이 만들어졌다. 즉 $1.3{\times}10^{-2}Torr$의 증착 진공도에서는 CrN 상만이 보이는 반면 $9.0{\tiems}1-^{-2}Torr$ 진공도에서부터 $Cr_2N$ 상이 형성되기 시작하여 $5.0{\tiems}10^{-2}Torr$ 진공도에서는 두개의 상이 혼재되어 있음을 알 수 있었다. 박막의 내마모성을 조사한 결과 CrN 박막의 마찰 계수는 초기에 급격하게 증가한 후 0.5에서 0.6 사이의 값으로 큰 변화를 보이지 않았으며, $Cr_2N$ 박막도 비슷한 거동을 보였다.

• Archives of Plastic Surgery
• /
• v.36 no.4
• /
• pp.385-392
• /
• 2009

Purpose: In the partial thickness burn management, despite of several advantages, the use of human amniotic membrane has been limited. The authors applied dried bovine amniotic membrane(DBAM) to overcome disadvantages of amniotic membrane for partial thickness burn and compared the effectiveness with cultured allogenic keratinocytes(CAK) that have been recently used for the management of burn. Methods: 16 patients with partial thickness burn, the mean age of 38 ranging 12 to 59 years, between August 2007 and May 2008 were assigned to this study. Either DBAM or CAK was applied, and the secondary dressing was removed on the following day. To compare treatment effect, time for epithelization, Vancouver scar scale and chromameteric results were evaluated. Results: The time for epithelization of DBAM was 10.1 days, that of CAK was 9.1 days, and they were shorter than the previous 2 - 3 weeks. At the follow up Vancouver scar scale was 2.8 for DBAM and 3.0 points for CAK and showed good results. The result of chromameter showed that the $L^*$, $a^*$, and $b^*$ values of the area applied DBAM were 60.1, 13.6, and 13.3, respectively, and the values of the area applied CAK were 60.1, 12.4, and 12.4, respectively. It was found that the skin color of the healed area after burn was darker, the redness was higher, and the yellowness was lower. After dressing, significant side effects were not observed, and in the cases of applying CAK, it was inconvenient as the moving area had to be fixed. Conclusion: With CAK, DBAM has several advantages such as the shortening of the epithelization period, reduction of scar and pigmentation, and convenient application, etc. Thus it is an effective method for the partial thickness burn management.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.18 no.2
• /
• pp.88-98
• /
• 2016

The storage variation in the vadose zone at a hillslope is important to understand the hydrological process. This study explores seasonal changes of soil water storage at a hillslope scale. The study was conducted on a hillslope of Beomrunsa, located in the Seolma-cheon river basin in Paju-si, Gyeonggi-do. Using soil moisture measurements through Time Domain Reflectometry (TDR), storage, discharge, and response constant were calculated for all monitoring points on a hillslope between March and November, 2010. This study found that temporal changes in storage are resulted from the rainfall distribution patterns. Analysis of the spatial changes in storage indicated that the soil water storage tends to increase towards the downslope direction. The discharges calculated based on the soil water measurements exhibited a high correlation with observation discharge. The storage response constant was high during the autumn which demonstrates the increased contribution from upslope is responsible for the occurrence of soil water recharge during autumn.

• Journal of Conservation Science
• /
• v.36 no.5
• /
• pp.368-382
• /
• 2020

It was confirmed that a white porcelain figurine in underglaze iron was damaged after exhibition. This study analyzes the current state of salt damage on the artifact and identifies the factors contributing to its deterioration by examining the material characteristics of the artifact and exhibition environment. The analysis will thus assist in preparing a conservation scheme for artifacts. The crystallized carbonate on the surface of the white porcelain figurine is a water-soluble alkali salt with high hygroscopicity and high solubility in water. This solubility increases as the temperature increases. The figurine was low-fired at approximately 1000℃. A lead glaze was applied, and thin cracks were formed on the glazed surface, indicating poor surface properties. Our analysis suggested that the showcase used in the exhibition likely created a moist environment resulting from condensation, as it was exposed to high temperature and relative humidity, particularly in comparison to the exhibition room where the temperature was regulated using an air conditioner. In addition, the artifacts in the showcase were exposed to sudden changes in temperature and relative humidity as the air conditioner was repeatedly turned on and off. Therefore, it can be deduced that the soluble salt remaining on the white porcelain figurine moved toward the surface of the relatively weak glaze as a result of the temperature, and the crystallized salt exacerbated surface damage as the moisture evaporated in a dry environment.

• Journal of Sensor Science and Technology
• /
• v.10 no.5
• /
• pp.292-303
• /
• 2001

This work reports the tunneling effects of the lateral field emitters. Tunneling effect is applicable to the VMFS(vacuum magnetic field sensors). VMFS uses the fact that the trajectory of the emitted electrons are curved by the magnetic field due to Lorentz force. Polysilicon was used as field emitters and anode materials. Thickness of the emitter and the anode were $2\;{\mu}m$, respectively. PSG(phospho-silicate-glass) was used as a sacrificial layer and it was etched by HF at a releasing step. Cantilevers were doped with $POCl_3(10^{20}cm^{-3})$. $2{\mu}m$-thick cantilevers were fabricated onto PSG($2{\mu}m$-thick). Sublimation drying method was used at releasing step to avoid stiction. Then, device was vacuum sealed. Device was fixed to a sodalime-glass #1 with silver paste and it was wire bonded. Glass #1 has a predefined hole and a sputtered silicon-film at backside. The front-side of the device was sealed with sodalime-glass #2 using the glass frit. After getter insertion via the hole, backside of the glass #1 was bonded electrostatically with the sodalime-glass #3 at $10^{-6}\;torr$. After sealing, getter was activated. Sealing was successful to operate the tunneling device. The packaged VMFS showed very small reduced emission current compared with the chamber test prior to sealing. The emission currents were changed when the magnetic field was induced. The sensitivity of the device was about 3%/T at about 1 Tesla magnetic field.

• Applied Chemistry for Engineering
• /
• v.18 no.5
• /
• pp.522-526
• /
• 2007

Structural features and electrochemical performances of cokes pyrolized from oxidized cokes were examined, and compared with KOH-activated coke. Needle cokes ($d_{002}=3.5{\AA} $), having a graphene layer structure, were changed to a single phase of graphite oxide after oxidation treatment with an acidic solution having an $NaCLO_3$/needle coke composition ratio of above 7.5, and the inter-layer distance of the oxidized coke was expanded to $6.9{\AA} $ with increasing oxygen content. After heating at $200^{\circ}C$, the oxidized coke was pyrolized to the graphene layer structure with inter-layer distance of $3.6{\AA} $. However, the change of the inter-layer distance of the needle coke was not observed in the KOH activation process. On the other hand, an intercalation of electrolyte ions into the pyrolized coke, observed at first charge, occurred at 1.0 V, in which the value was lower than that of KOH-activation coke. The cell capacitor using pyrolized coke exhibited a lower internal resistance of $0.57{\Omega}$ in 1 kHz, and a larger capacitance per weight and volume of 30.3 F/g and 26.9 F/ml at the two-electrode system in the potential range 0~2.5 V than those of the cell capacitor using KOH-activation of coke. This better electrochemical performance may be associated with structure defects in the graphene layer derived from the process of the inter-layer expansion and shrinkage.

• Journal of Sensor Science and Technology
• /
• v.11 no.2
• /
• pp.102-110
• /
• 2002

The chemical and mechanical characteristics of a new surface modifier, dichlorodimethysilane (DDMS, $(CH_3)_3SiCl_2$), for stiction-free polysilicon surfaces are reported. The main strategy is to replace the conventional monoalkyltrichlorosilane(MTS, $RSiCl_3$) such as octadecyltrichlorosilane (ODTS) or 1H,1H,2H,2H-perfluorodecyltrichlorosilane (FDTS) with dialkyldichlorosilane (DDS, $R_2SiCl_2$) with twit short chains, especially DDMS. DDMS, with shorter chains in aprotic media, rapidly deposits on the chemically oxidized polysilicon surface at room temperature and successfully prevents long cantilevers of 3 mm in length from in-use as well as release stiction. DDMS-modified polysilicon surfaces exhibit satisfactory hydrophobicity, long term stability and thermal stability, which are comparable to those of FDTS. DDMS as an alternative to FDTS and ODTS provides a few valuable advantages; ease in handling and long-term storage in solution, low temperature-dependence and low cost. In addition to the new modifier molecule, the simplified process of direct release right after washing the modified surface with isooctane was proposed to cut the processing time.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.81-85
• /
• 2004

Nanoporous materials with nanometer-sized pores, are of great interest in the various applications such as selective adsorbents, heterogeneous catalysts and catalyst supports because of their high porosity, surface area, and size selective adsorption properties. This study is aimed to prepare nanoporous catalytic materials on the basis of two-dimersional clay by pillaring of $SiO_2$ sol particles. $SiO_2$ Pillared Montmorillonite (Si-PILM) was prepared by ion exchanging the interlayer $Ni^{2+}$ ions of clay with $SiO_2$ nano-sized particles of which the surface was modified with nicked polyhydroxy cations sach as $Ni_4(OH)_4^{4+}$. Nano-sized $SiO_2$ particles were formed by the controlled hydrolysis of tetraethyl orthosilicate (TEOS). Upon pillaring of $Ni^+$-modified $SiO_2$ nano particles between the clay layers, the basal spacing was expanded largely to $45{\AA}$ and the extremely large specific surface area ($S_{BET}$) of $760m^2/g$ was obtained.