• Journal of Power System Engineering
• /
• v.4 no.2
• /
• pp.17-24
• /
• 2000

직경비가 0.26, 0.39, 그리고 0.56인 경우 거칠기를 내벽면에, 외벽면에, 그리고 양벽면에 각각 설치한 동심환형관에서 완전히 발달된 난류유동에 대한 거칠기 효과를 실험과 이론으로 해석하였다. 그리고 거칠기 효과를 정량적으로 파악하기 위해 양벽면 모두 매끈한 환형관의 경우도 포함하였다. 실험에서 마찰계수를 구하는데 필요한 속도분포와 전단응력들은 피토튜브와 X-형 열선풍속계를 사용하였다. 이론 해석은 수정대수 난류모델을 사용하였고 그 결과를 이론값과 비교하여 아래의 결론을 얻었다. 1) 무디다이어그램 (Moody diagram)은 거칠기가 설치된 이중관에는 적용할 수 없음을 보였다. 2) 경우(c) 와 (d)에서는 반경비가 클수록 반드시 마찰계수가 증가하지 않았다. 3) 4개의 경우중 거칠기로 인해 마찰계수가 증가하는 크기의 순서는 경우(d)가 가장 컸고 경우(a)가 가장 작았다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.170-178
• /
• 2019

Recently, as the interest in energy savings has increased, there has been increasing use of LED lighting, which is an eco-friendly device that replaces high energy consuming fluorescent lamps and incandescent lamps. In the case of a high output LED, however, the life time is shortened due to deterioration caused by heat generation. As a solution to this problem, this paper evaluated the LED life extension effect by increasing the convective heat transfer coefficient of the heat sink surface for LED packaging. A roughing process was carried out using sandpaper and sand blasting. The changes in surface roughness and surface area after each surface treatment process were evaluated quantitatively and the convective heat transfer coefficient was measured. When sandblasting and sandpaper were used to roughen the aluminum surface, a higher convection heat transfer coefficient was obtained compared to the untreated case, and a high heat dissipation efficiency of 82.76% was obtained in the sandblast treatment. Therefore, it is expected that the application of heat dissipation to the heat sink will extend the lifetime of the LED significantly and economically by increasing the heat efficiency.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.23 no.4
• /
• pp.153-178
• /
• 2018

Most operational uses of wind speed data require measurements at, or estimates generated for, the reference height of 10 m above mean sea level (AMSL). On the Ieodo Ocean Research Station (IORS), wind speed is measured by instruments installed on the lighthouse tower of the roof deck at 42.3 m AMSL. This preliminary study indicates how these data can best be converted into synthetic 10 m wind speed data for operational uses via the Korea Hydrographic and Oceanographic Agency (KHOA) website. We tested three well-known conventional empirical neutral wind profile formulas (a power law (PL); a drag coefficient based logarithmic law (DCLL); and a roughness height based logarithmic law (RHLL)), and compared their results to those generated using a well-known, highly tested and validated logarithmic model (LMS) with a stability function (${\psi}_{\nu}$), to assess the potential use of each method for accurately synthesizing reference level wind speeds. From these experiments, we conclude that the reliable LMS technique and the RHLL technique are both useful for generating reference wind speed data from IORS observations, since these methods produced very similar results: comparisons between the RHLL and the LMS results showed relatively small bias values ($-0.001m\;s^{-1}$) and Root Mean Square Deviations (RMSD, $0.122m\;s^{-1}$). We also compared the synthetic wind speed data generated using each of the four neutral wind profile formulas under examination with Advanced SCATterometer (ASCAT) data. Comparisons revealed that the 'LMS without ${\psi}_{\nu}^{\prime}$ produced the best results, with only $0.191m\;s^{-1}$ of bias and $1.111m\;s^{-1}$ of RMSD. As well as comparing these four different approaches, we also explored potential refinements that could be applied within or through each approach. Firstly, we tested the effect of tidal variations in sea level height on wind speed calculations, through comparison of results generated with and without the adjustment of sea level heights for tidal effects. Tidal adjustment of the sea levels used in reference wind speed calculations resulted in remarkably small bias (<$0.0001m\;s^{-1}$) and RMSD (<$0.012m\;s^{-1}$) values when compared to calculations performed without adjustment, indicating that this tidal effect can be ignored for the purposes of IORS reference wind speed estimates. We also estimated surface roughness heights ($z_0$) based on RHLL and LMS calculations in order to explore the best parameterization of this factor, with results leading to our recommendation of a new $z_0$ parameterization derived from observed wind speed data. Lastly, we suggest the necessity of including a suitable, experimentally derived, surface drag coefficient and $z_0$ formulas within conventional wind profile formulas for situations characterized by strong wind (${\geq}33m\;s^{-1}$) conditions, since without this inclusion the wind adjustment approaches used in this study are only optimal for wind speeds ${\leq}25m\;s^{-1}$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.6
• /
• pp.502-509
• /
• 2003

This paper describes a detailed experimental investigation of heat transfer in a reciprocating rectangular channel fitted with rib structures with particular reference to the design of a piston for marine propulsive diesel engine. The parametric test matrix involves Reynolds number, reciprocating frequency, and reciprocating radius, respectively in the ranges, 1,000～6,000, 1.7～2.5 Hz, and 7～15 cm with four different rib arrangements. The rib arrangements have considerable influences on the heat transfer in the reciprocating channel due to the modified vortex flow structure. The experimental data confirm that the increases in the heat transfer can be seen in order of Case (b), Case (c), Case (d), and Case (a).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.12
• /
• pp.5704-5708
• /
• 2012

In this paper, the algorithm to determine the optimal condition of traverse grinding is proposed by using differential evolution algorithm(DEA). The cost function to determine the optimal grinding condition is designed with considering process cost, production rate, surface roughness. Also, the constraint conditions for grinding such as thermal damage effect, machine tool stiffness, wear parameter of grinding wheel, surface roughness are considered. The algorithm is implemented with LabView software which is widely used at the industrial field. The performance of proposed algorithm is verified by comparing with the result of genetic algorithm(GA) through computer simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.2
• /
• pp.136-143
• /
• 1997

직경 비가 0.56인 이중동심관에 내외측모두 매끈한 벽면, 벽면 거칠기를 안측, 외측, 그리고 양측 모두의 4경우에 대한 난류 유동과 열전달특성을 실험과 이론으로 연구하였다. 시간평균속도분포, 마찰계수, 그리고 최대 속도 지점과 전단응력이 0인 지점들을 피토튜브와 X형 열선 풍속계로 측정하였다. 이중동심관내에서 4가지 경우에 따른 사각돌출형 거칠기효과가 난류 유동과 열전달에 미치는 영향을 수정난류모델을 기초로 하여 연구하였다. 직경비, 거칠기 위치, 레이놀즈수, 그리고 프란틀수 등의 여러 변수에 의해서 난류 유동과 열전달을 고찰하였다. 본 연구는 전체적 효율 측면에서 유리하게 열전달율을 향상시킬수 있는 거칠기 구조를 밝혔다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.47-48
• /
• 2006

A roughness measuring system which comprises an integrating sphere and a stabilized laser has been fabricated with the aim of measuring the roughness correction value which is necessary in gauge block measurement by optical interferometry. To calibrate the system, a Newton's ring interferometer has been introduced. The method how to calibrate the roughness measurement system has been described.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.5
• /
• pp.341-347
• /
• 2001

A comparison of fully developed heat transfer and friction factor characteristics has been made in rectangular ducts with ones roughened by five different shapes. The effects of rib shape geometries and Reynolds number are examined. The rib height-to-duct hydraulic diameter, pitch-to height ratio, and aspect ratio of channel width to height are fixed at $e$/De=0.0476, P/$e$=8, and W/H=2.33, respectively. To understand the mechanisms of the heat transfer enhancements, the measurements of the friction factors are also conducted in the smooth and rough channels. The data indicates that the triangular type rib has a substantially higher heat transfer performance than any other ones in the range we studied.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2014.04a
• /
• pp.815-818
• /
• 2014

영상 분석을 통한 특징 추출은 객체의 인식이나 매칭, 인덱싱 등을 위해 수반되는 준비 단계로서 분야별로 다양한 방식을 통해 수행되어 왔다. 특히, 피부 영상 분석에 있어 주목할 만한 이슈는 피부의 노화 정도를 측정하는 것이다. 피부의 거칠기는 피부의 상태와 노화를 판단하는 중요한 근거의 하나이다. 본 논문에서는 피부 나이를 측정하기 위해 피부 현미경 영상에서 피부 거칠기를 평가하는 방법을 제안한다. 이를 위해 피부 현미경으로 촬영된 이미지에 이진화 및 질감 대비 향상, 노이즈 제거 등의 전처리 과정을 수행하고, Watershed 알고리즘과 외곽선 검출을 통해, 피부를 구성하는 셀들의 영역 정보를 획득한다. 이를 바탕으로 피부 거침의 변화량을 계산하여 거칠기를 정의한다. 제안한 방법의 효과를 검증하기 위해 다양한 연령대의 피험자로부터 피부 현미경 영상을 확보하고 실험을 통해 피부 거칠기 특징이 피험자의 연령대와 상관관계가 있음을 보인다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1294-1303
• /
• 1993

The fully developed turbulent momentum and heat transfer induced by the square-ribed roughness elements on the inner wall surface in concentric annuli is studied analytically based on a modified turbulence model. The analytical results of the fluid flow is verified by experiment. The resulting momentum and heat transfer are discussed in terms of various parameters, such as the radius ratio, the relative roughness, the roughness density, fluid Reynolds number and for heat transfer, fluid Prandtl number. The study demonstrates that certain artificial roughness elements may be used to enhance heat transfer rates with advantages from the overall efficiency point of view.