• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.3
• /
• pp.292-298
• /
• 2011

This study examines the effects of the ambient temperature (AT), methanol feeding temperature (MFT), methanol concentration (MC) and methanol flow rate (MFR) on the performance and cell temperature (CT) of a 5-stacked direct methanol fuel cell (DMFC). The AT, MFT, MC, and MFR are varied from $-10^{\circ}C$ to $+40^{\circ}C$, $50^{\circ}C$ to $90^{\circ}C$, 0.5M to 3.0M and 11.7 mL $min^{-1}$ to 46.8 mL $min^{-1}$, respectively. The performance of the DMFC under various operating conditions is analyzed from the I-V polarization curve, and the methanol crossover is estimated by gas chromatography (GC). The performance of the DMFC improves significantly with increasing AT. The open circuit voltage (OCV) decreases with increasing MC due to the enhanced likelihood of methanol crossover. The cell performance is improved significantly when the MFR is increased from 11.7 mL $min^{-1}$ to 28.08 mL $min^{-1}$. The change in cell performance is marginal with further increases in MFR. The CT increases significantly with increasing AT. The effect of the MFT and MFR is moderate, and the effect of MC is marginal on the CT of the DMFC.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.27-38
• /
• 2016

This work proposes a 12b 30MS/s 0.18um CMOS SAR ADC based on low-power composite switching with an active die area of $0.16mm^2$. The proposed composite switching employs the conventional $V_{CM}$-based switching and monotonic switching sequences while minimizing the switching power consumption of a DAC and the dynamic offset to constrain a linearity of the SAR ADC. Two equally-divided capacitors topology and the reference scaling are employed to implement the $V_{CM}$-based switching effectively and match an input signal range with a reference voltage range in the proposed C-R hybrid DAC. The techniques also simplify the overall circuits and reduce the total number of unit capacitors up to 64 in the fully differential version of the prototype 12b ADC. Meanwhile, the SAR logic block of the proposed SAR ADC employs a simple latch-type register rather than a D flip-flop-based register not only to improve the speed and stability of the SAR operation but also to reduce the area and power consumption by driving reference switches in the DAC directly without any decoder. The measured DNL and INL of the prototype ADC in a 0.18um CMOS are within 0.85LSB and 2.53LSB, respectively. The ADC shows a maximum SNDR of a 59.33dB and a maximum SFDR of 69.83dB at 30MS/s. The ADC consumes 2.25mW at a 1.8V supply voltage.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.4
• /
• pp.285-289
• /
• 2000

This study suggests a rebar detection technique for simultaneous detection of size and cover of embedded reinforcement in concrete. The structure of the probe made in this study is somewhat different from commercial ones. This probe has three sensing coils. Rebar size and cover depth can be evaluated by detecting and analyzing the signal from them. Amplitude and phase variation of each coil in the probe was investigated using an impedance analyzer and the loci of transfer functions of the coils were analyzed. The locus of transfer function from the sensing coil positioned inside excitation coil was simple as well known, but the others from the coils outside excitation coil were not so. Actual experiment on rebar detection was performed with our probe and an eddy current test system for various rebar sizes and depths. The signal shape according to variation of cover depths showed the same tendency with the transfer function loci acquired by impedance analyzer. The different variation pattern of signal enabled to evaluate rebar size and cover depth simultaneously.

• Journal of IKEEE
• /
• v.19 no.4
• /
• pp.535-540
• /
• 2015

A microstrip gas chamber (MSGC), applied to digital radiography system, was designed and constructed. The microstrip electrodes were fabricated with Chrome(Cr.). by photolithography process on Silicon(Si) wafer and glass substrate. The width of anode and cathode electrodes was $10{\mu}m$, and $290{\mu}m$, respectively. The distance of the electrodes was $100{\mu}m$, and the active area was $50{\times}50mm^2$. And the number of anode was 80. The microstrip electrodes were damaged when discharges occurred over the 600 V of anode voltage. As the result of experiments. It detected the typical output signals of the pulse width, 20 ns, under the condition that the detecting gas was Ar(90%) + $CH_4$(10%), X-ray tube voltage was 42 kV, and tube current was 1 mA.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.494-500
• /
• 2005

In this paper, optical noise is reduced by a differential detector with an optical fiber coupler in an optical wireless system. An $1\times2$ optical fiber coupler divides the received optical signal by 2 equally, and connects them to the two photodiodes in a differential detector. The output voltage variation due to the abrupt change of optical noise distribution in space disappears because the two photodiodes effectively detect the optical signal at the same point. The signal to noise ratio in a differential detector with a fiber coupler was 8 dB higher than in a single photodiode with an optical filter.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.34.2-34.2
• /
• 2011

본 연구에서는 1986년에 국내 섬 지역에 설치된 태양전지 모듈을 대상으로 전기적 특성값의 열화 및 열화 원인에 대한 분석을 실시하였다. 태양전지 모듈의 초기 최대 출력값은 50 W였고, 5인치 단결정 실리콘 태양전지 36개로 구성되어 있었다. 첫째로, 육안 검사를 통해서 태양전지 모듈의 열화 현상을 관찰하였다. 태양전지 모듈의 절연성은 IEC 61215의 기준으로 측정하였다. 태양전지 모듈의 전기적 특성평가를 통해서 최대 출력값의 변화량을 측정하였고, EL(Electroluminescence) 측정을 통해서 태양전지의 열화를 분석하였다. 이를 통해 분석된 주요 열화 모드는 봉지재 (Encapsulant)의 변색(Discoloration) 및 박리(Delamination)현상이었다. 봉지재의 변색된 부분 및 변색되지 않은 부분의 태양광 반사도를 측정한 결과 변색된 부위의 반사도가 증가한 것을 확인하였다. 두번째로 최대 출력전압을 태양전지 모듈에 인가한 상태에서 태양전지 각각의 온도를 T.C (Thermocouple)을 이용하여 측정하였고, 이를 통해서 태양전지의 열화와 온도와의 관계를 분석하였다. 마지막으로 태양전지 모듈의 단면분석을 통해서 봉지재의 박리현상 및 리본와이어의 솔더 접합계면을 관찰하였다. 또한, 봉지재를 제거한 후에 SEM&EDX를 통해서 리본와이어 및 금속전극의 부식현상을 분석하였다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.5
• /
• pp.99-105
• /
• 2004

A shared-capacitor charge-sharing ROM (SCCS-ROM) using dummy bit lines is proposed. The SCCS-ROM reduces the bit line swing voltage using the charge-sharing technique of the conventional charge-sharing ROM (CS-ROM). Although the CS-ROM needs three small capacitors per output bit, the proposed SCCS-ROM shares the capacitors so that it needs only three capacitors. The SCCS-ROM implements the capacitors using dummy bit lines. This not only increases noise immunity but also reduces power. A SCCS-ROM with 8K${\times}$15bits implemented in a 0.35${\mu}{\textrm}{m}$ CMOS process. The SCCS-ROM consumes 8.63㎽ at 100MHz with 3.3V The simulation results show that the SCCS-ROM reduces 8.4% power compared to the CS-ROM.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.549-549
• /
• 2013

고전압 펄스 플라즈마를 액체 속에서 발생시켜 수소 스펙트럼의 광학적 특성을 연구하였다. 고전압 펄스 발생 장치인 막스 제네레이터는 용량이 $0.5{\mu}F$인 축전기 5개로 이루어져 있다. 각각의 축전기는 전원 장치를 이용하여 저항을 통해 병렬로 충전되며, 방전 시에는 불꽃 방전 스위치에 의해 동시에 직렬로 연결되어 고전압을 발생시킨다. 따라서, 출력 전압과 전류는 40kV, 3 kA이며 총 에너지는 약 125 J이다. 직육면체 모양의 폴리카보네이트 용기 내부의 양쪽면에는 탐침 모양의 전극이 구성되어 있으며 전극 사이에서 고전압을 가진 플라즈마가 형성된다. 실험에서 액체로는 증류수를 사용하였다. 액체 방전 시 발생하는 수소 스펙트럼을 관측하기 위해 초점거리 30 cm의 monochromator를 이용하였고, 수소 알파선의 656.3 nm와 수소 베타선의 434.1 nm를 관측하였다. 전자 밀도의 측정법으로는 Stark broadening법을 이용하여 측정하였으며, 전자 온도는 Stark profile의 상대적인 전자 밀도의 비를 이용하여 계산하였다. 전자밀도는 실험조건에서 약 $3{\times}10^{15}cm^{-3}$, 전자온도는 약 2.5 eV가 측정되었다.

• Journal of the Institute of Convergence Signal Processing
• /
• v.3 no.4
• /
• pp.74-78
• /
• 2002

For human detecting pyroelectric infrared sensor system using more than 2 sensor devices. By new top and bottom electrode design, 1 sensor can sensing human instead of using 2 sensor system. The poled P(VDF/TrFE) film used for sensor pyroelectric materials. The fabricated sensors NEP (noise equivalent power) and specific detectivity D$^*$ of the device were 9.62 $\times$ 10$10^5$ V/W, 3.95 $\times$ 10$10^-175$ W and 5.06 $\times$ 10$10^5$W under emission energy of 13 ${\mu}W/cm^2$ respectively and It's result is almost same result that using more than 2 sensor system for human detecting.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.5
• /
• pp.30-38
• /
• 2005

This paper proposes a new method which can calculates nodal price as an economic signal at non-optimal operation. By using pseudo constraints in 11 cases, we calculate shadow price and nodal price based on non-optimal operation. By comparing shadow price and nodal prices based on optimal and non-optimal operation effectiveness of the method is verified.