• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.11
• /
• pp.997-1002
• /
• 2008

This paper is mainly concerned with the development of a remotely operated vehicle for investigation of the coastal sea. For this, we have designed and constructed a vehicle entitled KMU-ROV(Korea Maritime University Remotely Operated Vehicle), for purpose of investigation mission under 50(m) of the sea surface. We have designed six independent waterproof actuators and the housing of the controller for underwater operation. For six degree-of-freedom motion, we have analyzed the dynamics of the KMU-ROV and have designed a new composition of six actuators including the driving system. For motion control, we have composed a concurrent velocity control algorithm for controlling the speed of all the actuating motors. The control system for the KMU-ROV is composed of a master DSP controller, DSP controller for the motor control and various sensors. We composed the PID control algorithm and a network system for controlling motors using the CAN communication. The performance of the KMU-ROV was presented by testing the developed control algorithm and control system under the water.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.192-198
• /
• 2001

In this study, a methodology of synchronous control which can be applied to position synchronization of a two-axes driving system has been developed. The synchronous error is caused by model uncertainties and torque disturbance of each axis. To overcome these problems, the proposed synchronous control system has been composed of two speed controllers and one synchronous controller. The speed controllers based on PID control law are aimed at the following to speed reference. And the parameters of speed controllers have been designed in order that speed response of the second axis corresponds with one of first axis. Especially, considering to model uncertainties of each axis, the synchronous controller has been designed using H$\infty$ control theory. The controller eliminates the synchronous error by controlling speed of the second axis. The effectiveness of the proposed method has been verified through simulation.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.9
• /
• pp.997-1005
• /
• 1990

Integral Error and State Feedback (IESF) controller which incorporates state feedback as a modern control scheme and integral action as a classical control scheme has better performance than that of conventional PID controller in linear time invariant system. But the structure of the IESF controller requires all the state variables of the system and is applicable only to pole assignable linear time invariant systems without time delay. Many industrial processes have large time delay and it is impossible to directly apply IESF control scheme to those processes. In this paper, a new controller structure, Modified Integral Error and State Feedback (MIESF) has been suggested in order to effectively control processes having time delay and its performance has been analyzed and its effectiveness has also been confirmed. As the proposed controller uses output feedback scheme based on integral error and state feedback (IESF) method, it can be simply designed by pole assignment algorithm irrespective of the order of the process. The MIESF controller can follow setpoint changes without overshoot. It is robuster than conventional Smith-Predictor plus PI(D) controller in case of occurring time delay mismatch and extra parameter mismatches between the process and the model. It can enhance control performance by intentional time delay mismatch.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.52 no.2
• /
• pp.74-80
• /
• 2003

In this paper, a robust two-degree-of-freedom(TDF) the speed control system using $H_{\infty}$ optimization method and real genetic algorithm is proposed for the robust stability and the robust performance in dc servo motor system. This control system composed of feedback and feedforward controller. The feedback(FB) controller with $H_{\infty}$ optimization method is designed for real genetic algorithm that is model matching problem using mixed sensitivity function. The feedforward(FF) controller with $H_{\infty}$optimization method is minimized the error between transfer function of the optimal model and the overall transfer function. The proposed robust two-degree-of-freedom speed control system is simulated to the dc servo motor. By the simulation, feedback controller can obtain the robust stability property and feedforward controller can obtain the robust performance property under modelling error. The performance of the dc servo motor is analyzed by the experiment setting. The validity of the proposed method is verified through being compared with pid(proportional integrated differential)control system design method for the dc servo motor.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2018.10a
• /
• pp.434-437
• /
• 2018

본 논문에서는 ROS (Robot Operating System)에 대해서 소개하고 ROS를 이용해 드론의 제어기와 필터를 구현해본다. 드론이 강인한 성능을 보이기 위해서는 기체의 상태에 대한 더 정확한 추정이 필요하다. 드론이 기체좌표계로 출력하는 각 축(x축, y축, z축)에 대한 선속도, 선가속도를 더 정확히 추정하기 위해 칼만 필터를 설계하며 칼만 필터를 통과한 상태 변수를 제어 입력으로 하는 PID(Proportional Integral Derivative) 제어기를 설계한다. 실험적인 부분에서는 제어기와 자율 주행 알고리즘을 접목시켜 드론이 자신의 상태를 추정하고 알고리즘을 순차적으로 진행하는 과정을 살펴본다. 마지막으로 알고리즘을 통해 드론의 임무 수행 여부를 살펴보고 정밀한 제어를 위한 추가적인 제어기 설계 방법과 연구 방향을 제시하고자 한다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.195-204
• /
• 2020

To help solve the problems of how to set the optimal sawing force and the optimal controller parameters for different sawing conditions, a mathematical model of a proposed sawing system was established according to the principle of sawing force control. The conventional PID control method was then used for further research of the closed-loop control of the sawing force. Finally, through simulation and experimental research, the influence rule of the controller parameters and sawing load on the control performance and the relationships between the sawing width and controller parameters (proportion coefficient) and the sawing force setting value were obtained, from which a system scheme for intelligent sawing control of a band sawing machine was proposed. The research shows that the sawing efficiency of the intelligent sawing system was 18.1 (48%) higher than that of the original sawing system when sawing a grooved section sawing material, which verifies the good control effect of the proposed scheme.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.5
• /
• pp.82-89
• /
• 2007

AVR(Automatic Voltage Regulator) of exciter control system in AC generator controls voltage and current according to load and terminal voltage variations in order to remain at the bus voltage. The output characteristics of main generator is dependent on the control performance of AVR. This paper presents the PWM type exciter system with transient response compensator for robust control of load variations. Additional transient response compensator generates compensation signal for load variation. So the proposed excitation control system has fast dynamic response in transient period and can control terminal voltage constantly. The proposed method is verified by the computer simulation and experimental results in prototype generation system.

• Journal of the Korean Society for Railway
• /
• v.18 no.1
• /
• pp.15-24
• /
• 2015

In magnetic levitation vehicles, the clearance between the magnet and track should be maintained within an allowable range through a feedback control loop. The flexibility of the guideway would introduce additional modes in the overall suspension system, resulting in dynamic interaction between the guideway vibration and the electromagnetic suspension control system. This dynamic interaction can be a serious problem, particularly at very low speeds or standstill, and may cause airgap instability. To optimize the overall system dynamics, an integrated dynamic model including mechanical and electrical parts and a flexible guideway as well as a control loop was developed. With the proposed model, airgap simulations at standstill were performed while varying the control gains, specifically with the aim of understanding the effects of gains of the PID controller on the airgap variation. The findings may be used to achieve a stable levitation controller design.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.518-523
• /
• 2008

Using network communication, KTX OBCS is KTX's core device which inspects operation status of various electric equipments and supports driving command, train control, train's maintenance, train crew's driving. Since this device is manufactured as specialized system, being dependent on TGV manufacture specification and France's high speed train operation method, actual technic transfer is difficult. Therefore, there are many difficulties, since most of interface signals are connected with OBCS when function improvement, maintenance, various electric equipments(propulsion control device, auxiliary power supply device, door control device etc.) are replaced with localized ones, which are required in operational view after introduction of KTX. Ergo, this study would like to contribute to function improvement and maintenance's efficiency, furthermore to realize technical independence, escaping from dependency of developed foreign technology in high speed train and electric equipments, through KTX OBCS' function analysis and mutual interface information analysis with peripheral device(driver console, PID system, fault display device, various electric equipments).

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.607-612
• /
• 1986

최근 테니스의 저변인구가 크게 증가함에 따라 테니스 라켓의 제작기술도 상당한 수준에 이르렀고 설계제작의 자동화에 의해서 양질의 제품이 시판되고 있다. 그러나 라켓에 볼이 임팩트될때 생기는 진동으로 야기되는 테니스 엘보우 등, 해결해야 할 문제들이 아직도 남아 있다. 이와같이 테니스 라켓의 정적인 강도 뿐만아니라 동적인 특성도 중요한 관심의 대상이 되어감에 따라 볼 컨트롤을 용이하게 한다거나, 안정타점영역(Sweet Spot)의 확장과 그립부의 진동등에 의해서 발생하는 엘보우 현상을 방지하기 위해 여러가지 연구가 수행되어 왔다. 특히, 다차원 스펙트럼해석 및 모우드 해석법에의해 그립부에 미치는 진동원의 동정과 라켓의 동적거동에 대해서 연구되었고, 라켓의 재질변경과 그립부의 구조변경에 의한 안정타점영역에 영향을 미치는 모우드 파라미터(Modal Parameter)의 추정에 관한 연구도 수행되었다. 이러한 연구들은 결국 안정타점영역을 확장시키거나 테니스 엘보우를 방지하기 위한 것으로서 이러한 목적을 달성하기위해 테니스 라켓의 진동 모우드에 관계되는 파라미터들을 찾아서 그 모우드 파라미터의 변화에 따르느 진동 모우드의 거동에 대해서 연구할 필요가 있다. 본 논문에서는 실험적인 모우드 해석법을 실제 테니스 라켓에 적용하여 모우드 파라미터들을 구한 다음 그 파라미터의 변화에 따르는 안정타점영역의 변화를 컴퓨터 시뮬레이션을 통해서 예측하였다. 또한 안정타점영역을 넓히고 라켓의 동특성을 개선시킬 수 있는 모우드 파라미터를 찾아서 테니스 라켓의 설계, 제작 단계에 정보를 제공하는 CAD(Computer Aided Design)에 좋은 자료를 얻고자 한다. 있으나 파도에 의한 영향이 가장 크므로 본 논문에서는 파도에 의한 영향만을 고려하였다. 파도는 쌍동선에 외란으로 작용하며 측정할 수 없는 양이므로 PID, LQ 제어에서는 제어모델에 포함되지 않지만 LQG 제어에서는 제어모델에 포함된다. LQG 제어의 경우 제어모델에 파도를 백색잡음으로 가정하고 제어기를 구성한 것 (LQG1)과 2차의 쉐이핑필터(shaping filter)를 사용하여 구성한 것(LQG2)으로 나누었다.져 한다.) 식도 이물에 의한, 또는 식도경술에 의한 합병증이 초래한 경우는 식도점막열상 1례 (1.8 %), 식도 천공 1례 (1.8 %) 였으며, 기도이물에 의한, 또는 기관지경술에 의한 합병증이 초래한 경우는 무기폐 2례 (11.1 %), 폐렴 3례 (16.7 %)로 나타났다.5예에서 소실되었다. 5 ) 청각심리검사 (Psychoacoustic evaluation)에서 폴립은 술전에 Grade 1∼2의 사성이 있었던 11예중 술후 10예에서 Grade 0로 되었으며 Grade 1∼2의 사성이 있었던 3예의 결절에서도 모두 Grade 0로 정상화되었다.>치를 측정한 결과 투여전과 차이가 없었다. 7) 이상의 결과로 볼때 Cis-platinum 사용으로 인한 이중독증은 신장기능이 정상일때는 충분한 hydration으로써 예방이 가능하며 동시에 금기로 알려져왔던 감음성난청이 있는 두경부악성종양환자에서도 세심한 주의하에 적절히 사용한다면 좋은 결과를 얻을 수 있을 것으로 사려된다.은 결과를 얻었기에 문헌고찰과 함께 보고하는 바이다. 1) 이관폐쇄술후 18시간에 최초로 삼출액이 확인되었으며 그 이후는 전실험군에서 삼출성중이염이 유발되다. 2