• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2664-2669
• /
• 2008

Feedwater heaters of many nuclear power plants have recently experienced severe wall thinning damange, which will increase as operating time progresses. Several nuclear power plants in Korea have experienced wall thinning damage in the area around the impingement baffle-installed downstream of the high pressure turbine extraction stream line- inside number 5A and 5B feedwater heaters. At that point, the extracted steam from the high pressure turbine is two phase fluid at high temperature, high pressure, and high speed. Since it flows in reverse direction after impinging the impingement baffle, the shell wall of the number 5 high pressure feedwater heater may be affected by flow-accelerated corrosion. This paper describes operation of experience and numerical analysis composed similar condition with real high pressure feedwater heater. This study applied squared, curved and new type impingement baffle plates to feedwater heater same as previous study. In addition, it shows difference of pressure distribution and value between single phase and two phase based on experience and numerical analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.3
• /
• pp.493-499
• /
• 2009

The assembled structures of pressure rice cooker are consisted of oven, top heater plate and locking ring. Since pressure is applied to the assembled structures, it should be necessary to check the safety. In this paper, structural analyses are performed from design and fracture point of view. For the design point of view, linear analysis is performed to assembled structure and for the fracture point of view, nonlinear analysis is performed to locking ring. From these results safety evaluation technique for the assembled structures of pressure rice cooker is proposed.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.5 s.143
• /
• pp.472-478
• /
• 2005

From a rapid cooling to a slow cooling in the actual cooling process in shipyards, the phase of steel becomes martensite, bainite, ferrite, and pearlite. In order to simulate the cooling process, heat transfer analysis was performed considering the effects of impinging water jet, film boiling, and radiation. From above simulation it is possible to find the cooling speed at the inherent strain region and volume percentage of all phases in that region. By the suggested method based on the precise material properties calculated from volume percentage of all phases, it will be possible to predict the plate deformations by line heating more precisely. It is verified by comparing with some experimental results that the present method is very effective and efficient.

• Journal of the Korean Solar Energy Society
• /
• v.35 no.1
• /
• pp.69-80
• /
• 2015

A series of numerical analyses was conducted to predict the thermal performance of a solar air heater depending on the hole configuration and geometry in the absorber plate. The planar dimensions of the prototype were 1 m (W) by 1.6 m (H), and the maximum air flow considered was $187m^3/h$. It was considered that protruding holes with a triangular opening in the absorber plate would invoke turbulence in the air flow to enhance the convection heat transfer. Six different hole configurations were investigated and compared with each other, while the hole opening height was considered as a design variable. Three-dimensional transient analyses were performed with a commercial software package on the airflow and heat transfer in the model. The numerical results were analyzed and compared from the view point of the outlet air temperature and its time response to derive the optimal hole pattern and hole opening height.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.7
• /
• pp.17-25
• /
• 2017

To resolve the problem of the temperature rise in LED or OLED lighting, until now a thick metal film has been used as a heat-sink. Conventionally, this thick metal film is made by the electroplating method and used as the heat-dissipating plate of the electronic devices. However, nowadays there is increasing need for a Cu metal film with a thickness of several hundred micrometers that can be formed by the dry deposition method. In this work, we designed and fabricated a Cu film deposition system where the heating element is separated from the ceramic crucible, which makes ultra-rapid deposition possible by preventing heat loss. In addition, the resulting induction heating also contributes to the high deposition rate. By tuning the various parameters, we obtained a $100-{\mu}m$ thick Cu film whose heat conductivity is high and whose thickness uniformity is better than 2%, while the deposition rate is as high as $1000{\AA}/s$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.1
• /
• pp.186-193
• /
• 2009

In this paper, we adopted E-MOLD patent technology in order to fabricate Prismless LGP(Light Guide Panel) fur cellular phone and estimate the transcription of injection-molded parts. Then, we manufactured the Ni stamper fur Prismless LGP using MEMS process. And the stamper was installed in the movable heated core which is the key part of a patented mold. Using this mold, we manufactured injection-molded plastic LGP parts with different mold temperatures so that we investigate effect of the temperature on the transcription of the parts. The CAE analysis was also conducted in order to compare with the experimental results. The transcription of LGP parts with various mold temperature displayed $100^{\circ}C$(25.0nm), $140^{\circ}C$(48.4nm), $180^{\circ}C$(52.1nm) and when compared with stamper(521Inm), transcription was superior at $180^{\circ}C$. According to the CAE results, moldability was improved as mold temperature ($50^{\circ}C{\sim}180^{\circ}C$) increased, but when filling time($1{\sim}2sec$) increases, it decreased at $160^{\circ}C$. And transcription and moldability were improved markedly at glass transition temperature($140^{\circ}C$).

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.7-16
• /
• 1999

This research was carried out to compare structure, equilibrium moisture content(EMC), adsorption and acoustical properties between 4 retention levels of saligenin(o-hydroxybenzyl alcohol) treated, heat-treated and untreated chestnut(Castanea crenata S. et Z.) and paulownia(Paulownia spp.) woods. The cell structures of untreated wood and heat-treated wood were not different but the cell wall of saligenin treated wood was thicker than that of untreated wood for both species. EMC of untreated wood was the highest, next was that of heat-treated wood, and that of saligenin treated wood was the lowest, and among saligenin treated woods, EMC was decreased as retention level increased for both species. Adsorption curves were parabolically increased. Acoustical properties of saligenin treated wood were most improved, and the next were those of heat-treated wood. Comprehensive acoustical property was improved at retention level 20% and 30% for chestnut wood, and at retention level 80% for paulownia wood.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.4
• /
• pp.116-127
• /
• 1999

Line heating is a method widely used in forming ship hull surface. From the viewpoint of mechanics it is large deformation thermal elasto-plastic problem of arbitrary shaped plate. Many researches have been carried out to resolve this problem. Especially, Jang et al.[1] proposed a simplified thermal elasto-plastic analysis method to predict effectively the deformation of plate due to line heating. In this paper, we improved the method of Jang et al.[1] by considering tension yielding in temperature decreasing stage and verified with experimental results. FEA program using MITC4 degenerated shell element was made to deal with elastic large deformation problem. The newly proposed method can be used in the simulation and control of forming hull surface for higher productivity with simplicity and efficiency.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.2
• /
• pp.105-114
• /
• 2016

When impact load is applied to a plate structure, a common phenomenon that occurs in structures is plastic deformation accompanied by a large strain and eventually it will experience a fracture accordingly. In this study, for the rational design against accidental limit state, the plastic material constants of steel plate which is formed by line heating and by cold bending procedure have been defined through the numerical simulation for the high speed tension test. The usefulness of the material constants included in Cowper-Symonds model and Johnson-Cook model with the assumption that strain rate can be neglected when strain rate is less than the intermediate speed is verified through comparing the present numerical results with those in references. This paper ends with describing the future study.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.566-566
• /
• 2013

종래의 흑연 위주 연료전지 분리판에서 최근 고분자 전해질 막 연료전지가 높은 전력, 낮은 작동 온도로 자동차 산업에서 상당한 주목을 받고 있다. 분리판의 기술적 요구사항은 높은 전기 전도도, 높은 내식성, 가스 밀봉성, 경량성, 가공성, 저비용 등이다. 후보 물질로는 전기 전도성을 갖는 질화물계가 고려되고 있다. 기판으로는 스테인레스강이 가장 유력하며 Fe에 첨가된 Ni, Cr이 존재하므로 Cr 또는 CrN를 박막의 형태로 전자빔 증발법, 마그네트론 스퍼터링법으로 고속 증착하려는 시도가 있었다. 본 연구에서는, 스테인리스 강박(0.1 mm 이하)에 보호막으로 CrN을 선택하고 고속, 고품질증착을 위해서 새로운 방법인 스퍼터 승화법을 개발하였다. 박막의 품질을 개선할 수 있는 고밀도 유도 결합 플라즈마 영역 내에 Cr 소스를 직류 바이어스 함으로써 가열 및 스퍼터링이 일어나도록 하였다. 5 mTorr의 Ar 유도 결합 플라즈마를 2.4 MHz, 500 W로 유지하면서 직류 바이어스 전력을 30 W (900 V, 0.02 A) 인가하고, $N_2$의 유량을 0.5, 1.0, 1.5 SCCM로 변화를 주어 반응성 증착 공정의 결과로 얻어지는 CrN 박막의 특성을 분석하였다. N2의 유량이 증가할수록 $Cr_2N$이 감소하고, CrN이 증가하는 것을 확인하였다. 또한 부식성과 접촉저항을 측정하였다. 부식 전위는 N20 SCCM 보다 모두 상승하는 것을 확인하였고, $N_21$ SCCM에서 부식 전류 밀도가 2.097E-6 (at 0.6V) $A/cm^2$로 나타났다. 접촉저항 에서는 시료 당 3군데(top, center, bottom)를 측정하였다. 전기전도도 측면에서 가장 좋은 결과는 $N_21$ SCCM 일 때 $28.8m{\Omega}{\cdot}cm^2$의 접촉저항을 갖는 경우였다. 미국 에너지성의 기준은 부식 전류밀도 1.E-6 $A/cm^2$이하, 접촉 저항 $0.02{\Omega}m^2$이므로 매우 근접한 결과를 보이고 있다.