• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.422-425
• /
• 2005

In an transversely isotropic composite laminates, the velocities, the particle directions and the amplitudes of reflected and transmitted waves were obtained using the equation of motion, the constitutive equation, and the displacement equation expressed by wave number and frequency Eigenvalue problem involving a velocity was solved by Snell's law. Finally, the results were confirmed by T300 Carbon fiber/5208 Epoxy materials. This approach could be applied to the detection of flaws in a transversely isotropic composite laminates by the water immersion C-scan procedure.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.2
• /
• pp.62-69
• /
• 2006

In transversely isotropic composite laminates, the velocities, the particle directions and the amplitudes of reflected and transmitted waves were obtained using the equation of motion, the constitutive equation, and the displacement equation expressed by wave number and frequency. Eigenvalue problem involving a velocity was solved by Snell's law. Finally, the results were confirmed by 7300 Carbon fiber/5208 Epoxy materials. This approach could be applied to the detection of flaws in transversely isotropic composite laminates by the water immersion C-scan procedure.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.3
• /
• pp.246-255
• /
• 1997

The wave washer springs are expected to behave non-linearly between forces and displace¬ments due to contractions of the height and due to expansions in radial direction. To find out the non -linearity of wave washer springs, the three dimensional plate analysis theory using the finite element method is adopted in this paper. The wave washer springs are considered to be three dimensional plate structures rather than frame structures, because their thickness is normally much smaller than their width. The displacements of nodal points due to small increment of force are calculated by the finite element method and the calculated nodal displacements are added to X - Y Z coordinates of nodal points. The new stiffness matrix of the system using the new coordinates of nodal points is adopted to calculate the another nodal displacements, that is, the step by step method is used in this paper. The relations between the increments of forces and displacements in each step are recorded and plotted in chart. The experimental results are compared with the calculated chart and it is shown that there are good coincidences between measured values and calculated ones.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.4
• /
• pp.114-120
• /
• 2018

Recently, the plate girder bridge is offen designed a temporary bridge for underground roadway construction have not interrupt railroad operation. The integral support plate girder bridge which have longitudinal girder and cross-girder is improved workability and reduction cost and of construction time. The cross beam of the integral support plate girder bridge has a normal box shape to distribute load on the main girde to end both side girder. In this study, On the change to the web distance of the cross box shows characteristics of related to the stresses and displacements on the flange and web plate. Afterward, the various analysis contributed to the safety improvement of crossbeam of the integral support crossbeam plate girder bridge.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.5
• /
• pp.118-125
• /
• 2019

In this study, the vibration characteristics and the resonance phenomena of a wind-solar hybrid light pole structure are compared with respect to the wind turbine type through the dynamic response measurement. Two different turbines are considered including 2-bladed and 3-bladed vertical axis wind turbine rotors. The resonance phenomenon that can occur in hybrid light pole structure is analyzed by comparing the dynamic characteristics of the structure and the excitation force under operational conditions. Displacement responses are also estimated using the acceleration measurement data by use of recently proposed method, and it is observed that the amplitude of dynamic displacement responses are in the range of 4-6 cm under the resonance in the case of 2-bladed turbine and those are limited under 2 mm in the case of 3-bladed turbine because there is no resonance.

• Journal of Navigation and Port Research
• /
• v.29 no.5 s.101
• /
• pp.415-420
• /
• 2005

LMTT (Linear Motor-based Transfer Technology) is the horizontal transfer system for yard automation, which has been proposed to take the place of AGV (Automated Guided Vehicle) in the maritime container terminal. The system is based on PMLSM (Permanent Magnetic Linear Synchronous Motor) that consists of stator modules on the rail and shuttle car. It is desirable to reduce the weight of LMTT in order to control the electronic devices with minimum energy. In this research, structural optimization for a mover of shuttle car is performed to minimize the weight satisfying design criteria. The objective function is set up as weight. On the contrary, the design variables are transverse, longitudinal and wheel beams' thicknesses and its height, and the constraints are considered as strength and stiffness.

• Journal of Aerospace System Engineering
• /
• v.9 no.3
• /
• pp.12-16
• /
• 2015

인간동력 항공기 TORUK MAKTO I에 대하여 양력선이론 및 XFOIL을 사용하여 도출한 공력계수 및 미계수 값과 CATIA를 사용한 관성모멘트 추정 값을 사용하여 지면효과 및 주익과 무게중심 사이의 수직거리 변화가 인간동력 항공기의 세로 정안정성에 미치는 영향과 수평미익(스테빌레이터) 변위각제어에 따른 세로 동안정성 해석 연구를 수행하였다. 연구결과 지면효과가 정적여유에 미치는 영향은 미미했다. 공력중심과 무게중심 사이의 수직거리가 세로 정안정성에 미치는 영향은 매우 컸으며, 수직거리 증가는 세로 정안정성을 증가시켰다. 수평미익 변위각 제어에 따른 세로 동안정성 해석 결과 장주기 진동특성과 감쇄특성이 매우 나쁜 것으로 나타났다. 향후 항공기의 동특성을 고려한 세로 동안정성 해석 및 측풍에 의한 가로 및 방향 안정성 해석연구를 수행할 예정이다.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.6
• /
• pp.225-232
• /
• 1997

철근콘크리트 유공보에 있어서 기존 유공보의 연구는 유공위치를 보춤의 중앙에 위치하여 연구하였으나 철근코크리트 보의 역학적 특성활용과 시공상의 편의성을 위해 사각형 유공의 위치를 보춤 하단에 설치하여 개방형 유공보로 변형하였다. 본 연구에서는 사각형 유공보에 대한 유공크기의 세로길이를 보춤의 0.3배로 하고 가로길이를 세로길의의 1~3배로 변화시켜 보강 및 무보강 상태의 사각형 유공보와 이의 사각형 유공하부 콘크리트를 제외시킨 개방형 유공보에 있어서 총 10개의 시험체를 대상으로 하는 실험을 실시하여 시험체의 최대내력, 유공주위에서의 전단균열과 시험체의 휨인장균열, 주요위치의 변위조사, 주근 및 유공주위의 콘크리트와 보강철근의 변형도조사, 시험체의균열을 조사하여 상호변화를 비교.분석하였다. 이 연구결과로부터 개방형유공보의 유공주위 응력변형상태, 파괴메카니즘, 적절한 개방형 유공크기,설계시 고려사항을 제시하여 차후의 개방형 유공보의 계속적인 연구에 기여하고자 한다.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.3
• /
• pp.321-330
• /
• 2009

This paper presents numerical analysis results for the lateral-torsional buckling (LTB) strength of steel I-girder bridges. Current Korean and AASHTO design specifications for LTB consider the buckling strength of a single girder with both its ends constrained. The I-girder bridges are composed of more than one girder, and the girders are interconnected with intermediate cross-beams or cross-frames. Therefore, it should be required to evaluate the effects of cross-beam stiffness and the interactionof girders on LTB strength. It is also necessary to consider the effects of transverse web stiffeners on LTB strength. By considering these parameters, a series of four-girder systemswere numerically modeled using 3D shell elements to estimate the LTB strength while considering initial imperfections and residual stresses.

• Journal of the Korean Society for Railway
• /
• v.14 no.3
• /
• pp.234-239
• /
• 2011

Installing the temporary bridge after excavating the railway requires installing movable cross beam, but as it doesn't requires isolating the catenary or cutting the rail, it's applicable to double-track with frequent operation. In this study, a displacement meter was placed on temporary bridge to monitor the displacement pattern in curve section (R400) completed using temporary bridge method, and wheel load, lateral pressure and derailment coefficient were measured to evaluate the load imposed on track and the stability in curve section (R400) for quantitative evaluation of training running safety. As a result of the measurement, when trains passing over a temporary bridge, the maximum value of Wheel load and Lateral Force is analyzed as the 51% and 81% of standard level according to foreign country's performance tests, There is no trouble with stability analysis in Wheel load and Lateral Force occurring. Additionally, Wheel load and Lateral Force considered as the safety standard are tested 49% of limiting value regardless of trains, which the norm value quite well, there is no problem with train running.