• Elastomers and Composites
• /
• v.39 no.1
• /
• pp.71-76
• /
• 2004

4,4'-Methylenebis(2-chloroaniline)(MOCA) has been widely used as a crosslinking agent, but classified as a toxic chemical. Thus, its use will be limited in the near future. In this research, polyurethane coating films were prepared using 1,3-propanediolbis(4-aminobenzoate)(PDBA) as an alternative to MOCA. The base part was prepared by melting MOCA or PDBA in polyoxypropylene($M_n$=2000), followed by the addition of the various additives. The NCO-terminated toluene diisocyanate prepolymer was used as a curing agent. The polyurethane coating films were prepared by mixing the base part with the curing agent in an appropriate ratio at room temperature. The polyurethane coatings prepared using PDBA exhibited higher initial viscosity, but much longer pot lift, compared to those prepared using MOCA under the same conditions, due to lower reactivity of PDBA. The tensile strength and tear strength of the coating films were much weaker. However, the pot life, tensile strength, elongation, and tear strength of the coating films, prepared using PDBA in the presence of an increased amount of Pb(II)-octoate, were close to those of the coating films prepared using MOCA. Thus, it was concluded that PDBA can substitute MOCA in the preparation of polyurethane coatings as long as the reactivity of PDBA is enhanced using appropriate amounts of the catalyst or other appropriate catalyst.

• Elastomers and Composites
• /
• v.47 no.1
• /
• pp.54-64
• /
• 2012

Acrylonitrile was introduced in the emulsion SBR to increase compatibility between silica and rubber. AN-SBR/silica compounds showed faster vulcanization time and higher delta torque values than SBR 1721/silica compounds because interaction between nitrile group of AN-SBR and silanol group on the silica surface could make hydrogen bond that prevented adsorption of the accelerator on the silica surface, which improved the vulcanization reaction efficiency and enhanced the degree of crosslinking. AN-SBR/silica compound showed higher values in minimum torque than SBR 1721/silica compound during the vulcanization because AN-SBR has higher molecular weight than SBR 1721 in the raw material. When PEG was added to the SBR 1721 and AN-SBR compounds, vulcanization time was faster than SBR 1721 and AN-SBR compounds without PEG because PEG has a large number of ether linkages which show high compatibility with silanol group on the silica surface that prevented the adsorption of the accelerator and the ingredients on the silica surface, which improved the vulcanization reaction efficiency. In the mechanical properties, AN-SBR compounds showed higher modulus values at 100%, 300% than SBR 1721 compounds because interaction between nitrile group of AN-SBR and silanol group on the silica surface enhanced the degree of crosslinking. In the dynamic properties, AN-SBR compounds showed lower tan ${\delta}$ values at $0^{\circ}C$ than SBR 1721 compounds in accordance with the $T_g$ values. AN-SBR compounds showed lower tan ${\delta}$ values at $60^{\circ}C$ than SBR 1721 compounds because interaction between acrylonitrile and silica caused strong filler-rubber interaction that induced low energy dissipation by the filler-filler interaction.

• Polymer(Korea)
• /
• v.24 no.1
• /
• pp.82-89
• /
• 2000

The blood compatibilities of PU/PVA polymer blends with different mixing ratios were evaluated using various methods, such as fibrinogen adsorption, plasma recalcification time, platelet adhesion, whole blood clotting time, and complement activation. In addition, PVA on the surface of the polymer blends was crosslinked by glutaraldehyde to restrain the mobility of PVA molecules for characterizing the effect of PVA in the polymer blends on blood compatibility. The fibrinogen adsorption on the polymer blends decreased with the increase of PVA amount in the polymer blends. The plasma recalcification times of the polymer blends with 10-50 wt% PVA were longer than those of PU, PVA, and polymer blends with higher amount of PVA. The morphological changes and adhesion of platelets on the polymer blends with 30-50 wt% PVA were less than those on the other materials. The blood clotting times and complement activation on the polymer blends with 30-50 wt% PVA were reduced, compared to the other materials. On the other hand, the blood compatibility of the crosslinked polymer blends was relatively decreased, compared to the non-crosslinked ones. According to these experimental results, the blood compatibility of the polymer blends with 30-50 wt% PVA was better than that of the other materials and such a blood compatibility of the polymer blends might be related to the mobility of PVA molecules on the surface.

• Elastomers and Composites
• /
• v.42 no.4
• /
• pp.249-258
• /
• 2007

In this study, the EPDM powder which was surface activated by high temperature and shear pulverization process was prepared and the mechanical properties and odor material analysis were investigated. Analysis for particle size and size distribution of waste of the EPDM powder has been performed. The waste EPDMs used in this study were 4 types of solid, sponge, solid+sponge, and solid+metal. According to the results, the solid type showed the smallest particle size among the 4 types of EPDM powder. Effective surface devulcanization of EPDM powder could be obtained by the addition of the reclaiming agent. The dicumyl peroxide was considered as the best crosslink agent for dynamic vulcanization when the surface activated EPDM powder was blended with polyolefin in order to make TPE. Also, the optimum amounts of DCP was 6 phr in terms of surface crosslink reaction and mechanical properties of EPDM powder. The processes of water adsorption and rose oil addition were employed to remove the odor of EPDM powder caused by reclaiming agent. The GC/MS was used to analyze the odor compounds.

• Polymer(Korea)
• /
• v.36 no.2
• /
• pp.208-215
• /
• 2012

To study the effect of surface crosslinked layer on the crosslinked poly(sodium acrylate) (cPSA) absorbent, we synthesized several surface crosslinked cPSAs with 5, 10 and 20 g of ethylene glycol dimethacrylate (EGDMA) by an inverse emulsion polymerization method to delay the absorption of excess water in concrete. We measured the compressive and flexural strength of mortars having 0.5, 1.0 and 1.5 wt% cPSA-EGDMA. We observed the increase of compressive and flexural strength of the cPSA-EGDMA added cement mortars except for the 0.5 wt% cPSA-EGDMA (20 g) added cement mortar. 1.0 wt% cPSA-EGDMA (5 g) added cement mortar showed about 16% and 10% increased compressive and flexural strength than those of plain cement mortar. To study the effect of porosity on compressive and flexural strength, we used FE-SEM and porosimeter. FE-SEM analysis showed swollen cPSMAEGDMA (5 g) filled between calcium silicate hydrate (C-S-H) crystals. We observed the decreased porosity of the cPSA-EGDMA added cement mortars than that of plain cement mortar. 1.0 wt% cPSA-EGDMA (5 g) cement mortar showed the lowest porosity of 16.5%.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.680-688
• /
• 1998

The macroreticular (MR) type glycidylmethacrylate (GMA)-divinylbenzene (DVB) copolymer (polyglycidylmethacrylate) beads (RG) were prepared by a suspension polymerization using 0~100 vol % of 2,2,4-trimethylpentane (TMP) as a diluent. Macroreticular type cation exchange resins containing phosphoric acid groups (RGP) were prepared by the reaction of GMA-DVB copolymer and poly (glycidyl methacrylate) bead (RG) with phosphoric acid in the presence of benzene. In this study, the effect of degree of crosslinking and the amount of the diluent on physical properties and adsorbability of uranium of RGP resins were investigated respectively. The chemical and physical properties of RGP resins were affected by both of the amount of the diluent and the degree of crosslinking. The effect of degree of crosslinking on the adsorbed amount of uranium for RGP resins were decreased in the order of $$RGP-10(50){\sim_=}RGP-1(50)>RGP-2(50)>RGP-5(50)>RGP-0$$. The effect of the diluent amount were as follows RGP-2(100)>RGP-2(75)>RGP-2(50)>RGP-2(30)>RGP-2(0). The crosslinking degree effect on uranium adsorbability depended on pore structure, cation exchange capability and swelling ratio. On the other hand, the effect of the diluent amount were relied on surface area and pore structure raher than cation exchange capability.

• Membrane Journal
• /
• v.29 no.3
• /
• pp.173-182
• /
• 2019

Much research has been made for finding new and eco-friendly alternative sources of energy to solve the problems related with the pollution caused by emissions of greenhouse gases such as carbon dioxide as the use of fossil fuels increases worldwide. Among them, fuel cells draws particular interests as an eco-friendly energy generator because only water is obtained as a by-product. Anion exchange membrane-based alkaline fuel cell (AEMFC) that uses anion exchange membrane as an electrolyte is of increased interest recently because of its advantages in using low-cost metal catalyst unlike the PEMFC (potton exchange membrane fuel cell) due to the high-catalyst activity in alkaline conditions. The main properties required as an anion exchange membrane are high hydroxide conductivity and chemical stability at high pH. Recently we reported a chemically crosslinked poly(2-dimethyl-1,4-phenylene oxide) (PPO) by reacting PPO with N,N,N',N'-tetramethyl-1,6-hexanediamine as novel anion exchange membranes. In the current work, we further developed the same crosslinked polymer but having enhanced physicochemical properties, including higher conductivity, increased mechanical and dimensional stabilities by using the PPO with a higher molecular weight and also by increasing the crosslinking density. The obtained polymer membrane also showed a good cell performance.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.108-114
• /
• 2008

Uniaxial tension and compression test were conducted on conventional and crosslinked ultra-high molecular polyethylene (UHMWPE) all prepared from the same lot of medical grade GUR 1050. The conventional materials were unirradiated and gamma irradiated with $25kGy{\sim}200kGy$. Gamma irradiated processing was found to significantly impact the crystallinity, and hence the mechanical behavior, of the highly crosslinked UHMWPE. The crystallinity and radiation dose were key predictors of the uniaxial yielding, hardness, plastic flow, and failure properties of conventional and highly crosslinked UHMWPE. The correlation model from experiments would be the basic information to design the liner of artificial joint.

• Journal of Conservation Science
• /
• v.34 no.3
• /
• pp.157-166
• /
• 2018

In this study, gelatin binding ability was increased by adding cross linking agent to improve adhesive characteristic of animal glue. Animal glue added genipin measured gel strength and viscosity, the structural analysis, the color retention degree, elution degree, and rupture strength. And the water resistance and ultraviolet light resistance with the addition of genipin were compared. As a result of the study, the gel strength and viscosity increased with the amount of genipin. As a result of the structural analysis, in gelatin, the absorption peak of the triple structure of collagen structurally stabilized was observed. As a result of the color retention degree, the film was observed because of the lowered brightness. The amount of elution glue was increased with addition of genipin at $50^{\circ}C$ distilled water condition and rupture strength has increased with the amount of genipin. In the water resistance and light fastness, there was no appearance before and after deterioration due to the addition of genipin. Based on the results of this study, it confirmed the adhesive characteristics of animal glue added genipin and examined the experimental method applicable for animal glue. After the addition of genipin, flexibility, re-solving, adhesive force, and curing speed, which are unique characteristics of glue, can be improved without disappearing, so it is expected that it will be applicable to production of animal glue and conservation of cultural heritage when homogeneous glue is secured.

• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.144-149
• /
• 2006

Non-halogen flame retardants have been the focus of extensive research because of environmental problems. Hexakisp-henoxycyclotriphosphazene was synthesized in order to use as the flame retardant of ABS resin. And using bisphenol A, the polymers containing a cyclotriphosphazene structure were synthesized in order to also use as the flame retardant of ABS resin. All of the synthesized polymers themselves had the excellent flame retardancy. And as their molecular weight and crosslinking density were increased, the thermal stability was increased. But when the synthesized compounds were used as the flame retardant for ABS resin, the lower molecular weight compound in these compounds showed the better flame retardancy and the better physical properties of ABS resin.