• Elastomers and Composites
• /
• v.38 no.4
• /
• pp.326-333
• /
• 2003

Even though many studies have been reported about rubber vulcanization, it is still remained difficult to find a quantitative relationship between the final states of vulcanized rubber and initial formulation or processing conditions. Dynamic differential scanning calorimetry (DSC) method is known as a comparatively easy method to research for the rubber vulcanization in both experimental and analysis. In the present research, a study on the vulcanization reaction of NR/CB composites modified by isoprene(IR) and chloroprene(CR) rubbers is carried out using dynamic DSC method. Thermograms with several different heating rates were obtained and analyzed using the Kissinger method. Analysis showed that the vulcanization reaction was progressed through the first order reaction mechanism. In addition, the reaction temperature was severely influenced by the kinds or rubber modifiers, in this case, more influenced by CR than by IR. Those effects were clearly verified in the values of activation energy. Kinds of carbon blacks, however, could hardly influence on the reaction mechanism.

• Polymer(Korea)
• /
• v.31 no.3
• /
• pp.239-246
• /
• 2007

The sulfonated ion exchange fibers were synthesized by $Co^{60}\;{\gamma}-ray$ radiation-induced graft copolymerization. Degree of grafting was increased with increasing the total dose. The degree of grafting for POF-g-St/DVB copolymer was 1000%. The ion exchange capacity of sulfonated ion exchange fibers were increased by increasing the degree of sulfonation. Its maximum value was 5.06 meq/g. The ion exchange capacity of sulfonated POF- co-St/DVB ion exchange fiber was higher than that of the sulfonated POF- co-styrene ion exchange fibers. The amount of adsorption for heavy metals were also increased with increase in the degree of grafting of the ion exchange fibers.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.689-697
• /
• 1998

In this work, we studied the equilibrium, rate and rate determining step of uranium adsorption on RGP resins of MR type prepared by varying the degree of crosslinking and the amount of diluent. The equilibrium of uranium adsorption on RGP resins were well explained by Frendrich isotherm as well as Langmuir isotherm model. The amount of adsorption and adsorption rate increase with the adsorption temperature. The heat of the adsorption was 11 kcal/mol. The adsorption rates of uranium on RGP resins were decreased in the order of RGP-10(50)>RGP-1(50)>RGP-2(50)>RGP-5(50)>RGP-0(50) and RGP-2(75)>RGP-2(100)>RGP-2(50)>RGP-2(30)>RGP-2(0). The diffusion resistance of uranium into RGP resin increased as follows; molecular diffusion < pore diffusion < surface diffusion. On the other hand, the surface diffusion was more dominative than the pore diffusion in intraparticle region. Thus, this result indicates that the adsorption mechanism of uranium on RGP resins is intraparticle diffusion controlled.

• Analytical Science and Technology
• /
• v.22 no.1
• /
• pp.92-100
• /
• 2009

Azacrown resins were synthesized by mixing 1-aza-12-crown-4 macrocyclic ligand into styrene (2th petroleum in 4th class hazardous materials) divinylbenzene (DVB) copolymer with crosslinkage of 1%, 2%, 5% and 10% by substitution reaction. The synthesis of these resins was confirmed by content of chlorine, element analysis, thermogravimetric analysis (TGA), surface area (BET), and IR-spectroscopy. The effects of pH, time, crosslinkage of resins and dielectric constant of solvent on adsorption of metal ions by resin adsorbent were investigated. Metal ions showed a great adsorption over pH 3 and adsorption equilibrium of metal ions was about two hours. In addition, adsorptive selectivity of metals on the resin in ethanol solvent was increased in the order of ${UO_2}^{2+}$ > $Ca^{2+}$ > $Sm^{3+}$ ion and adsorption of uranium ion was decreased with increase of crosslinkage such as 1%, 2%, 5% and 10% and was inversely proportional to the order of dielectric constant of solvents.

• Analytical Science and Technology
• /
• v.21 no.2
• /
• pp.109-116
• /
• 2008

Resins were synthesized by mixing 1-aza-18-crown-6 macrocyclic ligand into styrene(dangerous matter) divinylbenzene(DVB) copolymer with crosslink of 1%, 2%, 6% and 12% by substitution reaction. The synthesis of these resins was confirmed by content of chlorine, elemental analysis, thermogravimetric analysis, electron microscopy, and IR. The effects of pH, time, crosslink of resins and dielectric constant of solvent on adsorption of uranium ion by resin adsorbent were investigated. Uranium ion showed a great adsorption above pH 3 and adsorption equilibrium of metal ions was established in about two hours. In addition, adsorptive selectivity of resin in ethanol solvent was $UO{_2}^{2+}$ > $Zn^{2+}$ > $Lu^{3+}$ ion and adsorption of uranium ion increased with the increase of the degree of crosslinking (1%~12%) and was inversely in proportional to the order of dielectric constant of solvents.

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.233-239
• /
• 2001

The ethylene propylene diene terpolymer (EPDM) blends with acrylonitrile butadiene rubber (NBR) were prepared by mechanical mixing method. Mooney viscosity, cure behaviors, compression set and dynamic mechanical properties were subsequently examined. Dynamic characteristics of the entire blends determined from a Rheovibron generally showed two glass transitions (T'$_{g}$s), -43$^{\circ}C$ and -4$^{\circ}C$ for NBR and EPDM, respectively. The tan $\delta$ peak monotonically shifted toward the higher temperature with increasing NBR content. It was also found that the optimum cure time was significantly decreased with loading of NBR.

• Journal of Adhesion and Interface
• /
• v.11 no.2
• /
• pp.63-69
• /
• 2010

In this study, acryl resin PSA containing hydroxyl group based on 2-EHA (2-ethyl hexyl acrylate), 2-EHMA (2-ethyl hexyl methacrylate), 2-HEA (2-Hydroxy ethyl acrylate), acrylic acid was synthesized and then, isocyanate modified acryl resin PSA prepared with adduct reaction according to the amount of MOI (Methacryloyloxyethyl isocyanate) or 2-isocyanatoethyl methacrylate that can improve the curing property. This research shows that the initial PSA and peel adhesion are decreased according to the increase of the amount of the MOI and isocyanate curing agent. After UV irradiating, the peel adhesion is decreased with increasing the amount of the MOI (Methacryloyloxyethyl isocyanate) and isocyanate curing agent, because of the high curing property.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.4
• /
• pp.26-33
• /
• 1993

The acoustic emission automatic detection system is developed to observe tree deterioration phenomena. Applying an alternating voltage of 15(kVnns) toXLPE tree specimens, many pulses of small amplitude are detected when the bush type tree developes branch type and a few pulses of high amplitude prcxluced as branch type propagated to bush type tree. Therefore, it is known that pulses having small amplitude operates as a destructive factor. It is observed that the skewness of the amplitude and the number of average pulses as distribution tendency of three dimension are characteristic quantity of AE pulses. As the trajectory of skewness is farther from the origin on the S-plane, it is more likely to breakdown.

• Polymer(Korea)
• /
• v.36 no.2
• /
• pp.235-244
• /
• 2012

A thiazole type accelerator MBT (2-mercapto benzothiazole) was added into silica filled natural rubber (NR) compound with various concentrations (0, 1, 2, 3, 4 phr). The effects of MBT on the cure rate, mechanical property, degree of rubber-filler interaction (${\alpha}_F$), crosslinking density, and viscoelastic property ($tan{\delta}$) were investigated. As accelerator concentration increased, the $t_{s2}$ and $t_{90}$ decreased and the crosslinking density and modulus at 300% elongation increased. The tensile strength and elongation increased up to 3 phr and no further increased at 4 phr. The $tan{\delta}$ value measured at room temperature was higher than that of the $70^{\circ}C$. The ${\alpha}_F$ value was not affected by the addition of MBT. The mechanisms for the vulcanization rate were reviewed.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.287-298
• /
• 2000

In preparing micron-sized monodisperse polystyrene beads by dispersion polymerization, the conversion, and the particle size and its distribution were affected by the reaction temperature, concentration of the monomer, solvent and initiator, molecular weight and concentration of the steric stabilizer, amount of oxygen existing in the reactor, and an appropriate combination of these starting materials. Ethanol as a dispersing agent, styrene as a monomer, PVP as a steric stabilizer, AIBN as an initiator, DVB as a cross-linking agent and toluene as a co-solvent were the basic materials for the synthesis. The reaction rate and the conversion were increased with the reaction temperature and the amount of DVB from 1 to 4%, and the conversion was saturated after 10 hours of the reaction time. The optimum reaction recipe for the preparation of the monodisperse PS beads was 25% styrene monomer, 0.5% DVB, 25% toluene, 10-15% PVP, and 2 and 4% AIBN, thereby, 3.9~4 ${\mu}{\textrm}{m}$ and 3.4~9.3 ${\mu}{\textrm}{m}$ of polystyrene beads, respectively, were successfully synthesized.