• Composites Research
• /
• v.30 no.3
• /
• pp.193-201
• /
• 2017

Molecular dynamics simulation and the Mori-Tanaka micromechanics study are performed to investigate the effect of the covalent grafting between CNT and polyester on the mechanical behavior and load transfer of nanocomposites. The transversely isotropic stress-strain curves are determined through the tension and shear simulations according to the covalent grafting. Also, isotropic properties of randomly dispersed nanocomposites are obtained by orientation averaging the transversely isotropic stiffness matrix. By addressing the grafting, the transverse Young's modulus and shear moduli of the nanocomposites are improved, while the longitudinal Young's modulus decreases due to the degradation of the grafted CNT.

• Journal of Adhesion and Interface
• /
• v.16 no.2
• /
• pp.63-68
• /
• 2015

We synthesized thermoplastic polyurethane elastomer containing carboxylic acid group and TPV (thermoplastic vulcanizate). We measured the mechanical, grip, debris, contact angle and adhesion properties according to introducing acid group in elastomer structure. Mechanical and wet slip properties were improved because of the hydrogen bonding by introduction of acid group. Also adhesion strength was increased as increasing of surface polarity by carboxylic acid group. The debris property of TPV made from TPU containing carboxylic acid group was improved.

• Journal of the Korean Electrochemical Society
• /
• v.1 no.1
• /
• pp.55-59
• /
• 1998

The water absorption in protective coatings, which may greatly influence the durability of these coatings, was studied using quartz crystal microbalance and electrochemical impedance technique. The water absorption in protective coatings and the change of coating capacitance with concentration of electrolyte were measured. The water absorption in coatings seems to be driven by osmotic pressure, and larger amount of water was absorbed in thinner coatings at initial stage of absorption. The amount of water absorbed in coatings changed with the type and crosslinking density of resin used in coating formulation. When water absorption and desorption of coating occured by exposing the coatings to electrolyte solutions of different concentration, increase in impedance caused by desorption of water was found to be higher in the case of thinner film.

• Elastomers and Composites
• /
• v.36 no.2
• /
• pp.79-85
• /
• 2001

It goes to be serious with environmental pollution cause waste rubber. That is why there are lot of studies for efficient recycle. The purpose of this study is to improve the physical properties of EPDM powder by using De-link system. We changed on the size of waste rubber powder and De-link contents. we examined the physical, rheological, mechanical properties. And also examined cross-link state at various De-link. Also we carried out morphological studies after making the weather strip's feature by optical microscope.

• Journal of Adhesion and Interface
• /
• v.22 no.2
• /
• pp.47-56
• /
• 2021

Steel plates coated by self-healable polymer still can be rusted since it takes time to be healed. In this study, dual self-healing coating material is developed using corrosion inhibitor (DTBEDA) which can form hindered urea (HUB) as reversible cross-linking bond at the same time. Developed dual self-healing polymer is coated on steel plate, and scratch healing property was investigated by surgical blades and nano/micro indentation tester. The anticorrosion effect of DTBEDA was investigated by electrochemical impedance spectroscopy (EIS).

• Composites Research
• /
• v.32 no.3
• /
• pp.127-133
• /
• 2019

Although carbon nanotubes(CNTs) have outstanding theoretical mechanical and electrical properties, CNT fibers(CNTFs) have not yet reached that level. Particularly, tensile strength is only about 10% or less, so studies for making up for it are being actively conducted. As a way for improving mechanical strength, methods such as synthesizing long CNT, orientation, chemical cross-linking, hydrogen bonding and polymer infiltration are being studied. In this review paper, we report preparation methods for highly conductive and strong CNTF/Carbon composites through coating and infiltration followed by carbonization of carbon precursor polymers such as polyacrylonitrile (PAN) and polydopamine (PDA) on CNTFs.

• Membrane Journal
• /
• v.28 no.2
• /
• pp.113-120
• /
• 2018

Global warming due to indiscriminate carbon dioxide emissions has a profound impact on human life by causing abnormal climate change and ecosystem destruction. As a way to reduce carbon dioxide emissions, in this study, we presented a polymeric membrane prepared by blending a self-crosslinkable P(GMA-g-PPG)-co-POEM (SP) copolymer and commercial polymer polyvinylpyrrolidone (PVP). As the content of PVP increased, it was observed that the gas permeance decreased and $CO_2/N_2$ selectivity increased. At 30 wt% PVP content, the $CO_2$ permeance of the membrane decreased from 72.9 GPU of pure SP polymer to 12.6 GPU, while $CO_2/N_2$ selectivity improved by 79% from 28.1 to 50.4. It results from the hydrogen bonding between the SP copolymer and PVP, leading to more compact structure of the polymer chains, which was confirmed by FT-IR, TGA, XRD and SEM analysis. Therefore, we suggest that the permeance and selectivity of the membranes can be easily adjusted as desired by controlling the PVP content in the SP/PVP polymer blend.

• Journal of Conservation Science
• /
• v.32 no.2
• /
• pp.223-234
• /
• 2016

Two-component epoxy resin is widely used in the cultural heritage restoration field. However according to mixing ratio of resin and hardener, curing property, mechanical strength and chemical structure differ which have possibility to effect the stability of cultural heritage. Result of questionnaire survey shows hands-on workers in the conservation field tend to mix the epoxy resin with his or her eye measurement when the using amount is small or mix additional hardener to shorten the pot life of epoxy resin. This research aims to analyze the curing property, mechanical strength and chemical structure of rapid curing type epoxy resin and medium curing type one depending on relative ratio of 0.25~4 of hardener to resin. When the amount of hardener was 0.5~2 times more than the resin, exothermic heat and curing speed were both increased. In case of included hardener to resin was lower than official ratio, mechanical strength (tensile shear strength, tensile strength and compressive strength) became higher along with active cross-linking bonding of the epoxy resin. Medium curing type epoxy relatively had lower exothermic heat and slower reaction during curing process. It was observed to be put to definite point of mechanical strength under lower content of hardener than official ratio. While, hardener ratio more than twice the resin slowed down the curing greatly and lowered the adhesion strength also. In conclusion, under the lower mixing rate of hardener than official ratio would show relatively fast reaction with similar mechanical strength. Over the official ratio on the other hand, material property drops rapidly. Accordingly, mixing ratio of epoxy resin is expected to be influential to the stability of cultural heritage.

• Journal of Conservation Science
• /
• v.34 no.3
• /
• pp.157-166
• /
• 2018

In this study, gelatin binding ability was increased by adding cross linking agent to improve adhesive characteristic of animal glue. Animal glue added genipin measured gel strength and viscosity, the structural analysis, the color retention degree, elution degree, and rupture strength. And the water resistance and ultraviolet light resistance with the addition of genipin were compared. As a result of the study, the gel strength and viscosity increased with the amount of genipin. As a result of the structural analysis, in gelatin, the absorption peak of the triple structure of collagen structurally stabilized was observed. As a result of the color retention degree, the film was observed because of the lowered brightness. The amount of elution glue was increased with addition of genipin at $50^{\circ}C$ distilled water condition and rupture strength has increased with the amount of genipin. In the water resistance and light fastness, there was no appearance before and after deterioration due to the addition of genipin. Based on the results of this study, it confirmed the adhesive characteristics of animal glue added genipin and examined the experimental method applicable for animal glue. After the addition of genipin, flexibility, re-solving, adhesive force, and curing speed, which are unique characteristics of glue, can be improved without disappearing, so it is expected that it will be applicable to production of animal glue and conservation of cultural heritage when homogeneous glue is secured.

• Elastomers and Composites
• /
• v.49 no.1
• /
• pp.24-30
• /
• 2014

3-Amino-1,2,4-triazole (ATA) (2.5 and 5.0 phr) was incorporated into a immiscible maleated ethylene propylene diene rubber(mEPDM)/maleated high density polyethylene(mHDPE) (50 wt%/50 wt%) blend by melt mixing. Effects of the ATA on structure, mechanical and rheological properties of the blend was investigated. FT-IR and DMA results revealed that supramolecular hydrogen bonding interactions between the polymer chains occur by reaction of ATA with maleic anhydride grafted onto the component polymers in the blend, which induces the physical crosslinks in the blend. FE-SEM analysis showed that mEPDM forms a dispersed phase in continuous mHDPE matrix, and the blend with the ATA has finer phase morphology as compared to the blend without the ATA. By the addition of ATA in the blend, there were significant increases in tensile strength, modulus and elongation-at-break as well as elastic recoverability. Melt rheology studies revealed that ATA induced substantial increase in storage modulus and complex viscosity of the blend at the melt state.