• Journal of the Korea Convergence Society
• /
• v.12 no.9
• /
• pp.161-168
• /
• 2021

As the demand for high speed and high precision increases in the field of machine tool, interest in stiffness and vibration of machine tool is increasing. However, it takes a lot of time to develop a detailed design of machine tool based on experience, and it is difficult to design appropriately. Recently, structural optimization using FEM are increasingly used in machine tool design. But, it is difficult to optimize in consideration of the vibration state of the structure since optimization through stress distribution of a structure is mainly used, In this paper, Static structural analysis, mode analysis, and harmonic analysis using FEM were conducted to optimize the head structure that has the most influence on machining in a 5-axis machine tool. It is proposed a topology optimization analysis method that considers both static stiffness and dynamic stiffness using objective function design.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3158-3163
• /
• 2013

In this study, squeal noise test was conducted by using the lab-scaled brake dynamometer. Squeal conditions with respect to the angle of the brake pads ($34^{\circ}30^{\circ}26^{\circ}$) and negative slope, were studied. Squeal frequency of the In-plane-like mode was confirmed by hammering test and finite element analysis. This Squeal mode was difficult to control by the pad angle variation. Also the squeal sound was found to be periodic signal which has higher harmonic components. Squeal noise is independent of the negative slope. It implies that squeal noise can reach the stick-slip oscillation.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.382-384
• /
• 2011

최근 오일샌드, 극지유전, 심해저자원 등 극한지 자원개발이 활발해짐에 따라 수요가 증대되고 있는 극한지용 내마식 소재는 내마식성과 함께 저온 인성이 요구되고 있다. 철계 합금에서 관찰되는 변형유기 마르텐사이트 상변태는 입자의 충돌에 의한 충격을 흡수하고 소재의 표면을 가공경화시켜 내마식성 향상 및 저온 인성에 기여할 수 있을 것으로 기대되고 있지만 합금조성의 정교한 제어가 필요하기 때문에 오버레이 용접에 적용하기 위해서는 모재와의 희석률을 제어하는 방안이 필요하다. 용접플럭스 설계기술은 용접시 금속이행모드, 용융풀 거동 등과 같은 용접현상 제어를 통해 오버레이 용접재료의 용접성과 용접비드형상, 용접부 희석률을 최적화할 수 있는 기술이다. 본 연구에서는 내마식 고인성 오버레이 용접재료의 개발을 위해 다양한 용접플럭스를 첨가한 메탈코어드 와이어를 제조하고 일정 송급속도에서 GMA 용접시 용접전압과 용접전류 간의 관계를 분석하여 용접플럭스가 아크현상 및 희석률에 미치는 영향을 조사하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.842-846
• /
• 1997

Micro-hole drilling (holes less than 0.5 mm in diameter with aspect ratios larger than 10) is gaining increased attention in a wide spectrum of precision production industries. Alternative methods such as EDM, laser drilling, etc. can sometimes replace mechanical micro-hole drilling but are not acceptable in PCB manufacture because they yield inferior hole quality and accuracy. The major difficulties in micro-hold drilling are related to wandering motions during the inlet stage, high aspect ratios, high temperature,etc. However, of all the difficulties, the most undesirable one is the increase of drilling force as the drill penetrates deeper into hold. This is caused mainly by chip related effects. Peck-drilling is thus widely used for deep hole drilling despite the fact that it leads to low productivity. Therefore, in this paper, a method of cutting force regulation is proposed to achieve continuous drilling. A proportional plus derivative (PD) and a sliding modecontrol algorithm will be implemented for controlling the spinle rotational frequeency. Experimental results will show that sliding mode control reduces the nominal cutting force and its variation better than the PD control, resulting in a number of advantages such as an increase in drill life, fast stabilization of the wandering motion, and precise positioning of the hole.

• Composites Research
• /
• v.33 no.5
• /
• pp.262-267
• /
• 2020

With increasing demands for high-speed machining and lightweight design of machine tools, increasing likeliness of generation of machine tool spindle vibrations has become an important issue. Spindle vibration has a significant impact on the surface finish of the workpiece in ultra-precision machining. It is necessary to resolve the machine tool spindle vibration in various machining processes to improve machining accuracy. In this paper, a TiC-SKH51 metal-matrix composite was used to suppress the vibration of the machine tool spindle. To confirm the dynamic characteristic of the TiC-SKH51 composite, impact hammer tests were conducted. After verifying the reliability of a finite element analysis (FEA) by comparing the results of the impact hammer test with the modal analysis using FEA, the analysis of the machine tool spindle model was performed. The FEA results show that the TiC-SKH51 composite applied machine tool spindle can be utilized to suppress the vibration generation.

• Journal of the Korean Magnetics Society
• /
• v.13 no.3
• /
• pp.115-120
• /
• 2003

We have developed laser micro-machining technology for fabrication of the micro thin-film inductors. After the thin layers of FM/M/FM films were coated to the silicon substrate by using the conventional sputtering method, the new laser machining was applied to the patterning process that used to be carried out by the semiconductor lithography procedure. A CW Nd:YAG laser operating in TEM$\sub$00/ mode was actively Q-switched to obtain the very short pulse of 200 ns. The laser micro-machining process with pulse energy and repetition rate have been optimized as 5 mJ/pulse and 5 kHz, respectively, to obtain the line resolution as fine as 20 $\mu\textrm{m}$.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.97-97
• /
• 2010

최근 자동차에서 경량화의 방안으로써 높은 강성을 요구하는 고장력강 사용이 증대 되고 있다. 그러나 고장력강은 저항 점용접 시 일반 강에 비해 높은 전류를 요구하며 계면파단 및 expulsion 발생이 용이하기 때문에 가용 전류 구간이 좁은 특성을 가진다. 많은 연구자들이 hold time, tempering 등의 process를 이용하여 고장력강의 저항 점용접성을 개선하고자 하였으나 생산 공정라인에 적용하기는 어려운 실정이다. 본 연구에서는 용접 공정 변수의 변화에 따른 용접성과 전극 형상 변화을 통한 고장력강 점 용접성 향상에 대한 연구를 실시 하였다. 고장력강의 점 용접성 비교하기 위해 표준 전극(S1)과 인위적으로 가공한 전극(M1)을 사용하였으며, 실험에 사용된 판재는 두께 1.4mm의 DP590이며, 그 결과 표준전극(S1) 보다 가공 전극(M1)의 가용 전류 구간이 0.5kA 정도 넓은 것으로 확인 되었다. 두 전극을 사용한 점용접 시험편들의 인장전단강도를 비교 해보면 표준전극(S1)을 적용한 점용접 시 인장전단강도는 KS B 0850 기준에 만족하나 계면 파단이 발생 하였다. 가공 전극(M1)을 적용한 점용접 시 인장전단강도는 규격 기준에 만족하나 버튼 파단이 발생 하였다. 두 전극을 적용한 점용접부 형상 및 용접부 온도 분포에대해 저항점용접 시뮬레이션 프로그램(SORPAS)을 이용하여 실험 결과 값과 비교 분석하였고 파단모드의 변화에 대한 원인 분석을 도출 하였다.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.1-6
• /
• 1999

European spruce and maple were to be estimated as raw material of violin family instruments with linear modal analysis to provide the information data for the design of their bodies. Wood specimens cut in different direction were excited by impact hammer to measure the resonant frequency with typical vibrational modes. In spite of lower density than maple, European spruce showed the excellent acoustical properties with higher resonant frequency. And edge-grained spruce had more even frequencies than flat-grained ones to be more acceptable as front plate of violin. Resonant frequency was positively correlated with wood density of each specimen and the coefficients of edge-grained specimens were higher than those of flat-grained specimens of both wood species.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.306-306
• /
• 2007

최근, LED 구동 인버터, DC-DC 컨버터, AC-DC 컨버터 및 형광등 ballaster 등의 고전압전원장치등에 압전변압기를 적용하고자 하는 연구가 활발히 진행되고 있다. 순수한 $PbTiO_3$는 큐리온도($490^{\circ}C$)가 높고, 기계적강도가 크며, 비유전율(약 200 정도)이 작다. 또한, 두께방향 진동의 전기기계 결합계수 ($K_t$)가 윤곽진동의 전기기계 결합계수($K_p$)보다 크므로 두께방향의 진동모드를 이용한 벌크파 진동자의 경우 윤곽진동방향으로 불요신호(spurious signal)가 적고, 작은 grain size($1\;{\mu}m$정도)로 미세가공이 가능하여 고주파 재료로 이용되고 있다. 압전변압기의 출력 전력을 향상시키기 위해서는 적층으로 제작하여야 하는데 적층 압전변압기 제작시 층간의 내부 전극이 도포된 상태에서 소결하여야 한다. 이때 소걸 온도가 높으면 Pd 함랑이 높은 전극을 사용하여야 하는데 Pd 전극의 가격이 비싸 소자의 경제성이 떨어지게 된다. 따라서 순수한 Ag 전극을 내부전극으로 사용하기 위해서는 $900^{\circ}C$ 이하에서 소결이 가능하여야 한다. 따라서 본 연구에서는 $(Pb,Ca,Sr)Ti(Mn,Sb)O_3$ 조성을 이용하여 $900^{\circ}C$ 이하의 저온소결이 가능한 두께방향진동모드 적층 압전변암기를 제작하여 그에 대한 전기적 특성을 조사하였다.

• Journal of Korean Ophthalmic Optics Society
• /
• v.16 no.2
• /
• pp.107-115
• /
• 2011

Purpose: To design and fabricate the distributed auto edging machine for the development. Methods: We got the necessary data needed in design by using CAD. Based on the these data, we fabricated the trial product for the development of the distributed auto edging machine. Results: The patternless mode could be operated by receiving the eyesize data from the auto lay-outer with the RS232C transmission system and the pattern mode could be operated by setting the pattern on the left side of the machine. The distributed auto edging machine were composed with combinations of many elements; head, auto arm, pattern clamp and grinding wheels. The head part controlled the grinding of ophthalmic lens by operating the vertical and horizontal motors. The wheels part was comprised of glass mode, plastic mode, V-bevel mode and polish mode. The slide in the auto arm was equipped on the below of the patten and the slide could hold up the pattern which was rotated by fixed shaft. The pattern clamp could move the head part to the up and down or right or left way by the manual operation of optometrists. Conclusions: We could succeed in making the trial product by applying it to the development of the distributed auto edging machine which could be used as the patternless mode and pattern mode, selectively. Therefore, it was confidently expected that this product was very helpful for the optometrists to dispense the ophthalmic lens because of its cost-efficiency and convenience.