• Journal of Korea Foundry Society
• /
• v.20 no.4
• /
• pp.254-259
• /
• 2000

Metal matrix composites(MMCs) reinforced with hard particles have many potential application in aerospace structures, auto parts, semiconductor package, heat resistant panels, wear resistant materials and so on. In this work, the effect of SiC partioel sizes(50 and 100 ${\mu}m$) and additional elements such as Si, Cu and Ti on the microstructure and the wear property of $Al-5Mg-X(Si,Cu,Ti)/SiC_p$ composites produced by pressureless infiltration method have been investigated using optical microscopy, scanning eletron microcopy(SEM) with EDS(energy dispersive spectrometry), hardness test, X-ray diffractometer(XRD) and wear test. In present study, the sound $Al-5Mg-X(Si,Cu,Ti)/SiC_p$(50 and 100 ${\mu}m$) composites were fabricated by pressureless infiltration method. The $Al-5Mg-0.3Si-O.1Cu-O.1Ti/SiC_p$ composite with $50 {\mu}m$ size of SiC particle has higher hardness and better wear property than any other composite with $100{\mu}m$ size of SiC particle produced by pressureless infiltration method. The hardness and wear property of $Al-5Mg/SiC_p$(50 and 100 ${\mu}m$) composites were enhanced by the addition of Si, Cu and Ti in Al-5%Mg matrix alloy.

• Journal of the Korean Ceramic Society
• /
• v.32 no.10
• /
• pp.1194-1202
• /
• 1995

The influences of TiC additions to the α-SiC on microstructural, mechanical, and electrical properties were investigated. Electrical discharge machinability of SiC-TiC composites was also studied. Samples were prepared by adding 30, 45, 60 wt.% TiC particles as a second phase to a SiC matrix. Sintering of SiC-TiC composites was done by hot pressing under a vacuum atmospehre from 1000 to 2000℃ with a pressure of 32 MPa and held for 90 minutes at 2000℃. Samples obtained by hot pressing were fully dense with the relative densities over 99% except 60wt.% TiC samples. Flexural strength and fracture toughness of the samples were increased with the TiC content. In case of SiC samples containing 45 wt.% TiC, the fracture toughness showed 90% increase compared to that of monolithic SiC sample. The crack propagation and crack deflection were observed with a SEM for etched samples after Vicker's indentation. The electrical resistivities of SiC-TiC composites were measured utilizing the four-point probe. The electrical dischage machining of composites was also conducted to evaluate the machinability.

• Korean Journal of Materials Research
• /
• v.12 no.11
• /
• pp.883-888
• /
• 2002

We investigated the void formation in composite-titanium silicide($TiSi_2$) process. We varied the process conditions of polycrystalline/amorphous silicon substrate, composite $TiSi_2$ deposition temperature, and silicidation annealing temperature. We report that the main reason for void formation is the mass transport flux discrepancy of amorphous silicon substrate and titanium in composite layer. Sheet resistance in composite $TiSi_2$ without patterns is mainly affected by silicidation rapid thermal annealing (RTA) temperature. In addition, sheet resistance does not depend on the void defect density. Sheet resistance with sub-0.5 $\mu\textrm{m}$ patterns increase abnormally above $850^{\circ}C$ due to agglomeration. Our results imply that $sub-750^{\circ}C$ annealing is appropriate for sub 0.5 $\mu\textrm{m}$ composite X$sub-750_2$ process.

• Tribology and Lubricants
• /
• v.4 no.2
• /
• pp.36-43
• /
• 1988

Titanium carbide(TiC) and titanium nitride(TiN) flims were deposited on $Si_3N_4$-TiC composite cutting tools by chemical vapor deposition(CVD) using $TiCl_4-CH_4-H_2$ and $TiCl_4-H_2-N_2$ gas mixtures, respectively. The nonmetal to metal ratio of deposit increases with increasing $m_{C/Ti}$(mole ratio of CH$_4$ to TiCl$_4$ in the input) for TiC coatings and $m_{N/Ti}$(mole ratio of N$_2$ to TiCl$_4$ in the input) for TiN coatings. The nearly stoiahiometric films could be obtained under the deposition condition of $m_{C/Ti}$ between 1.15 and 1.61 for TiC, and that of $m_{N/Ti}$ between 25 and 28 for TiN. Also maximum microhardness of the coatings can be obtained in these ranges. The interfacial region of TiC coatings on $Si_3N_4$-TiC ceramics is wider than that of TiN coatings according to Auger depth profile analysis, which indicates good interfacial bonding for TiC. Experimental results show that TiC coatings have an randomly equiaxed structure and Columnar structure with(220) preferred orientation can be obtained for TiN coatings. And, multilayer coatings have a dense and equiaxed structure.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.6
• /
• pp.245-249
• /
• 2006

In this study, ternary Ti-Mo-N and new quaternary Ti-Mo-Si-N coatings were synthesized on steel substrates(AISI D2) and Si wafers by a hybrid coating system of arc ion plating (AIP) using Ti target and d.c. magnetron sputtering technique using Mo and Si targets in $N_2/Ar$ gaseous mixture. Ternary Ti-Mo-N coatings were substitutional solid-solution of (Ti, Mo)N and showed maximum hardness of approximately 30 GPa at the Mo content of ${\sim}10$. %. The Ti-Mo-Si-N coating with the Si content of 8.8 at. % was a composite consisting of fine (Ti, Mo)N crystallites and amorphous $Si_3N_4$ phase. The hardness of the Ti-Mo-Si(8.8 at. %)-N coatings exhibited largely increased hardness value of ${\sim}48$ GPa due to the microstructural evolution to the fine composite microstructure and the refinement of (Ti, Mo)N crystallites. The average friction coefficient of the Ti-Mo-Si-N coatings largely decreased with increase of Si content. The microstructures of Ti-Mo-Si-N coatings were investigated with instrumental analyses of XRD, XPS, and HRTEM in this work.

• Korean Journal of Materials Research
• /
• v.1 no.1
• /
• pp.9-17
• /
• 1991

TiC coating formed on $Si_3N_4-TiC$ composite ceramic by chemical vapor deposition (CVD) has an improved microstructures, better thermal shock resistance and interfacial bonding than TiN coating does. TiN coating formed by CVD, however, has lower friction coefficients against steels and better chemical stability. The experimental results indicate that the coated insert is superior to the uncoated one in flank and crater wear resistance. And the multilayer coating shows an improved wear resistance than the monolayer coating.

• The Korean Journal of Ceramics
• /
• v.6 no.2
• /
• pp.91-95
• /
• 2000

Powder mixtures of $\beta$-SiC-TiC in a weight ratio of 2:1 containing 5-20 wt% additives ($Al_2O_3$-$Y_2O_3$) were liquid-phase sintered at $1830^{\circ}C$ for 1h by hot-pressing and subsequently annealed at $1950^{\circ}C$ for 6h to enhance grain growth. The annealed specimens revealed a microstructure of \"in situ-toughened composite\" as a result of the $\beta$longrightarrow$\alpha$ phase transformation of SiC during annealing. The increase of the content of additives accelerated the growth of elongated $\alpha$-SiC grains with higher aspect ratio and improved fracture toughness. The fracture toughness of SiC-TiC composite containing 20 wt% additive was 6.2 MPa.$m^{1/2}$.2}$.

• Journal of the Korean Ceramic Society
• /
• v.35 no.10
• /
• pp.1020-1029
• /
• 1998

The reaction-bonded TiC-Ni/Si/Co composites were prepared by the melt infiltration of Co, Si, and Ni me-tal into the TiC preforms. The miocrostructure reaction composition and mechanical properties were in-vestigated. In the case of the melt infiltrated with Co and Ni TiC grain shape was changed from angular to spherical shape with the average grain size of ∼5$\mu\textrm{m}$. In the case of the melt infiltrated with Co/Si or Ni/Si, Si was reacted with TiC particles and formed SiC particles. The bending strength of both specimens which have atomic ratio of 3 were 710 MPa and 515 MPa respectively. In the case of the melt infiltrated with Ni/Si/Co,. nonstoichiometric TiC was formed and its bending strength decreased to 420 MPa.

• Journal of the Korean Ceramic Society
• /
• v.53 no.1
• /
• pp.87-92
• /
• 2016

Due to its stability at high temperature and its layered structure, $Ti_3SiC_2$ MAX phase was considered to the interphase of $SiC_f/SiC$ composite. In this study, $Ti_3SiC_2$ MAX phase powder was deposited on SiC fiber via the electrophoretic deposition (EPD) method. The Zeta potential of the $Ti_3SiC_2$ suspension with and without polyethyleneimine as a dispersant was measured to determine the conditions of the EPD experiments. Using a suspension with 0.03 wt.% ball milled $Ti_3SiC_2$ powder and 0.3 wt.% PEI, $Ti_3SiC_2$ MAX phase was successfully coated on SiC fiber with an EPD voltage of 10 V for 2 h. Most of the coated $Ti_3SiC_2$ powders are composed of spherical particles. Part of the $Ti_3SiC_2$ powders that are platelet shaped are oriented parallel to the SiC fiber surface. From these results we expect that $Ti_3SiC_2$ can be applied to the interphase of $SiC_f/SiC$ composites.

• Journal of Korea Foundry Society
• /
• v.15 no.4
• /
• pp.368-376
• /
• 1995

An Al-composite material was fabricated with using the rheocompocasting process and the microstructure of the Al-Cu/SiCp composite material was investigated depending on the stirring times and the amount of Ti additions. The distribution of SiC dispersion shows the good result at the stirring time of 30 min. The degree of microdistribution of the $Al_2Cu$ and SiCp is improved when the amount of Ti addition is increased. At the compositon of 0.3%Ti, the primary solid is the compound of $Al_3Ti$ and no exist of the SiCp and $Al_2Cu$ phase around the primary $Al_3Ti$. In the process of compositization, SiCp is found at the primary and final solid parts and is found at the final solid part after remelting. $Al_2Cu$ and SiCp are distributed around and outside of dendrite or independently after remelting, which is different from the process of compositization.