• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.8
• /
• pp.950-958
• /
• 1988

We have implemented a RTA system using W-halogen lamps and tried to recrystallize the phosphorus ion implanted amorphous silicon on insultor (SOI) taking advantages of seeding window. The purpose of this study is to investigate the possibility of a typical crystalline orientation occurred during the solidifying process of molten amorphous silicon layer. Experimental results show that several twin boundaries are found on the seeding window region after annealing for 15 sec at 1040\ulcorner. These twin boundaries represent that the recrystallization is partialy possible and when the annealing is done at 1150\ulcorner, (100) etch pits with <110> facets are found on the solidified amorphous silicon layer. Consequently, Hall mobility of recrystallized silicon film is measured and the thermal behavior of grain boundary is also observed by SEM.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.77-80
• /
• 2006

Structural phase transformations of silicon during nanoindentation were investigated in detail at the atomic level. The molecular dynamics simulations of nanoindentation on the (100), (110) and (111) surface of single crystalline silicon were simulated, and this supported the theoretical prediction of the anisotropic behavior of structural phase transformations. Simulations showed that microscopic aspects of phase transformation varied according to the crystallographic orientation of the contact surface and were directly linked to the slip system.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.107-110
• /
• 1999

본 연구에서는 진공압추출법에 의해 제조되는 알루미나(AI$_2$O$_3$) 단섬유예비성형체의 제조공정시 발생하는 섬유들의 배향분포의 특징을 2차원 수치모사를 통해 밝혔다. 수치해석은 섬유의 배향분포를 2차원으로 가정한 후 제조공정시 섬유들이 적층되는 현상을 섬유의 낙하, 회전, 미끄러짐, 이동의 단계의 나누어 모델링하였다. 해석결과 섬유의 배향과 부피분율은 섬유의 종횡비(길이/지름)에 의해 크게 영향을 받으며, 배향 분포는 정규분포와 유사한 것으로 밝혀졌다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.3
• /
• pp.110-117
• /
• 1998

A continuum-based configuration design sensitivity analysis method is developed for kinematically driven mechanical systems. The configuration design variable for mechanical systems is defined. The 3-1-3 Euler angle is employed as the orientation design variable. Kinematic admissibility conditions of configuration design change. Direct differentiation method is used to derive the governing equations of the design sensitivity. Numerical examples are presented to demonstrate the validity and effectiveness of the proposed method.

• 한국정보컨버전스학회:학술대회논문집
• /
• 2008.06a
• /
• pp.103-110
• /
• 2008

In this thesis, we describe a statistical method for 3D object detection. In this method, we decompose the 3D geometry of each object into a small number of viewpoints. For each viewpoint, we construct a decision rule that determines if the object is present at that specific orientation. Each decision rule uses the statistics of both object appearance and "non-object" visual appearance. We represent each set of statistics using a product of histograms. Each histogram represents the joint statistics of a subset of wavelet coefficients and their position on the object. Our approach is to use many such histograms representing a wide variety of visual attributes. Using this method, we have developed the first algorithm that can reliably detect faces that vary from frontal view to full profile view and the first algorithm that can reliably detect cars over a wide range of viewpoints.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.505-508
• /
• 1987

The structure of vacuum evaporated PbO films is investigated. Also, the Photosensitivity and dark resistivity are measured. The dominant structure and orientation of these films were red (tetragonal) form, and <110> and <101> direction under- the suitable deposition conditions. And the crystallite size of them was about $2um{\times}0.2um$. These PbO films have good photosensitivity(r=0.9) and high dark resistivity. (${\rho}=10^{14}{\Omega}{\cdot}cm$)

• Electrical & Electronic Materials
• /
• v.10 no.7
• /
• pp.668-673
• /
• 1997

A Single-crystalline Mn-Zn Ferrite (110 orientation) was masklessly etched by focused Ar laser irradiation in an H$_3$PO$_4$ solution. The depth of the etched grooves increases with increasing a laser power, decreasing a scan speed, and increasing the H$_3$PO$_4$concentration. The width of the etched grooves increases with a increasing laser power, but was relatively insensitive to the scan speed and H$_3$PO$_4$concentration. High etching rate of up to 714 ${\mu}{\textrm}{m}$/s and an aspect ratio of 6 for vertical slab structure have been obtained by the light-guiding effect of the laser bean in the H$_3$PO$_4$ solution.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.106-110
• /
• 2002

4S-Van is being developed in order to provide the spatial data rapidly and accurately. 4S-Van technique is a system for spatial data construction that is heart of 4S technique. Architecture of 4S-Van system consists of hardware integration part and post-processing part. Hardware part has GPS, INS, color CCD, camera, B/W CCD camera, infrared rays camera, and laser. Software part has GPS/INS integration algorithm, coordinate conversion, lens correction, camera orientation correction, and three dimension position production. In this paper, we suggest that adequate 4S-Van design is needed according to application environment from various test results.

• Journal of Korean Society for Quality Management
• /
• v.27 no.1
• /
• pp.101-110
• /
• 1999

Products are often evaluated on rating scales to measure and quantify their attributes of interest. In case that one wishes to compare multiple rating datasets simultaneously, there must be a standardized scale with which one can discriminate relative differences among corresponding scale means. In this regard, the concept of Thurstonian modeling applied to various discrimination tests including the triangular method has been recently being reconsidered. In this paper we extend previous researches on the triangular method and evaluate the effect of unequal variances and correlated variables upon the probability of correct response using Monte-Carlo simulation. We observed that the probability of correct response depends on dimensionality, variances, and correlation structure of stimulus sets. But it does not depend on the relative orientation in a multidimensional space.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.3
• /
• pp.195-202
• /
• 1996

The composition, the microstructure and the magnetic properties(HC and Hk) of Fe-Co-Ni alloy electrodeposits were investigated according to the electrolysis conditions using sulfate bath paddle agitated. The current efficiency of the alloys electrodeposition was considerably low in the range of 16∼50%. The Fe content(wt.%) of the alloy increased from 20% to 57% with current density, while Ni content of them decreased in the range of 70∼24% respectively, and Co content was nearly constant. As a result, Fe/Ni ratio of the alloy increased from 0.3 to 2.0 showing the anomalous codeposition. The structure of the alloy changed from fcc to the mixed one of fcc+bcc with the increase of Fe/Ni ratio. The preferred orientation of the alloy with fcc and bcc structure were (220) and (110) respectively. The alloy with Fe/Ni ratio(0.3∼l.2) had the lowest coercivity of 0.4∼0.8 Oe.