• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.6
• /
• pp.113-120
• /
• 2007

Chemical vapor deposition (CVD) is one of the various synthesis methods that have been employed for carbon nanotube (CNT) growth. In particular, Ren et al reported that large areas of vertically aligned multi-wall carbon nanotubes could be grown using a direct current (dc) PECVD system. The synthesis of CNT requires a metal catalyst layer, etchant gas, and a carbon source. In this work, the substrates consists of Si wafers with Ni-deposited film. Ammonia $NH_3$) and acetylene ($C_2H_2$) were used as the etchant gases and carbon source, respectively. Pretreated conditions had an influence on vertical growth and density of CNTs. And patterned growth of CNTs could be achieved by lithographical defining the Ni catalyst prior to growth. The length of single CNT was increased as niclel dot size increased, but the growth rate was reduced when nickel dot size was more than 200 nm due to the synthesis of several CNTs on single Ni dot. The morphology of the carbon nanotubes by TEM showed that vertical CNTs were multi-wall and tip-type growth mode structure in which a Ni cap was at the end of the CNT.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.188-203
• /
• 2021

The specific benefits of the modified films formed on preliminary anodized aluminum, including the versatility of their potential applications impose the need for evaluation of the exploitation reliability of these films. In this aspect, the durability of Cu and Ni modified anodized aluminum oxide (AAO) films on the low-doped AA1050 alloy was assessed through extended exposure to a 3.5% NaCl model corrosive medium. The electrochemical measurements by means of electrochemical impedance spectroscopy (EIS) and potentiodynamic scanning (PDS) after 24 and 720 hours of exposure have revealed that the obtained films do not change their obvious barrier properties. In addition, supplemental analyses of the coatings were performed, in order to elucidate the impact of the AC-deposition of Cu and Ni inside the pores. The scanning electron microscopy (SEM) images have shown that the surface topology is not affected and resembles the typical surface of an etched metal. The subsequent energy dispersive X-ray spectroscopy (EDX) tests have revealed a predominance of Cu in the combined AAO-Cu/Ni layers, whereas additional X-ray photoelectron (XPS) analyses showed that both metals form oxides with different oxidation states due to alterations in the deposition conditions, promoted by the application of AC-polarization of the samples.

• Economic and Environmental Geology
• /
• v.30 no.1
• /
• pp.1-14
• /
• 1997

The shales from the Euiseong area are interbedded along the bedding in Cretaceous Gyeongsang Supergroup, which are composed mainly of quartz, plagioclase, K-feldspar and associated with trace amount of biotite, muscovite, chlorite, pyrite, hematite, carbonate and clay minerals. The ratio of $Al_2O_3/Na_2O$ and $K_2O/Na_2O$ in shales from the Shindong Group are ranged from 9.16 to 24.32 and from 1.70 to 5.97, and the Hayang Group ranged from 2.76 to 8.89 and from 0.42 to 2.74, which are negative correlated between $K_2O/Na_2O$ and $Al_2O_3/Na_2O$ against $SiO_2/Al_2O_3$ respectively. Those are suggested that controlled of mineral compositions in shales due to substitution and migration of elements by sedimentation and diagenesis. These shale formation were deposited in basin of terrestrial environments originated from the igneous rocks, and the REE of these rocks are not influenced with diagenesis and hydrothermal alterations on the basis of $Al_2O_3$ versus La, La against Ce, Zr versus Yb, the ratios of La/Ce (0.43 to 0.62) and Th/U (1.11 to 10.71). The narrow range in trace and REE element characteristics as Co/Th (0.63 to 1.92), La/Sc (1.98 to 5.90), Sc/Th (0.58 to 1.30), V/Ni (0.90 to 3.25), Cr/V (0.45 to 1.78), Ni/Co (1.88 to 6.67) and Zr/Hf (30.04~60.87) of these shales argues for inefficient mixing of the simple source lithologies during sedimentation. These rocks also show much variation in $La_N/Yb_N$ (6.90 to 17.02), Th/Yb (4.17 to 13.68) and La/Th (1.98 to 5.90), and their origin is explained by derivation from a mixture of intermediate to acidic igneous rocks.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.39 no.1
• /
• pp.16-22
• /
• 2006

Mineral and heavy metal contents were determined in three brown edible seaweeds (sea mustard, Undaria pinnatifida; seaweed fusiforme, Hizikia fusiforme; sea tangle, Laminaria japonica) collected from Gijang and Wando in Korea, and two green seaweeds (sea lettuce, Enteromorpha prolifera; green laver, Monostroma nitidum) collected from Gijang. Seaweeds contained high proportions of ash (13.8-24.8%) and sulfate (1.08-3.25%). In brown seaweeds, ash contents (24.5-24.8%) were higher than in green seaweeds (13.8-15.2%). The differences of mineral contents were remarkable in both Gijang and Wando and in 5 various kinds of seaweeds. Brown seaweeds contained higher amounts of both macro-minerals (657-13,947 mg/100 g; Ca, Mg, Na, K) and trace elements (0.27-12.98 mg/100 g; Fe, Al, Zn, Mn, Cr, Cu, Ni), and green seaweeds also had relatively higher amounts of both macro-minerals (233-5,279 mg/100 g) and trace elements (0.26-10.61 mg/100 g).

• Transactions of the Korean hydrogen and new energy society
• /
• v.1 no.1
• /
• pp.24-30
• /
• 1989

Prototype metal hydride chemical heat pump was constructed using $LaNi_{4.7}Al_{0.3}$ for high temperature hydride and $MmNi_{4.15}Fe_{0.65}Al_{0.2}$ for low temperature hydride, and the effects of operating conditions on the performace of heat pump were investigaed to find out the optimum operating condition. Operating variables considered in this work were cycling time, temperature of hot air blown to the high temperature reactor, the amount of hydrogen gas with which the system was charged initially, and the flow rate of air at both reactors. Power of heat pump increases monotonically as $T_h$ increases, and shows maxima at 4.8H/M and 15-25 min in $H_2$ charged and cycling time respectively. Power of heat pump increases as air flow rate increases at low flow rate, but saturates to some value confined by heat flow rate through the hydride bed, These all phenomena can be explained by the modified power equation.

• Journal of Environmental Health Sciences
• /
• v.24 no.3
• /
• pp.1-5
• /
• 1998

A spectrophotometric method was developed for the acidic solution stripped after an extraction of 0.5 to 2.5 ppm of Lead(II) from 50 mL of $Na_2S_2O_3$ solution into chloroform as the ion-pairs formed between their thiosulfate complexes and alkylamine, Aliquat336. Pb(II) in the stripped solution forms an complex with DDTC in pH 7.3 buffer solution, and was developed in yellow by copper replacement. The ydlow-colored solution have the maximum absorbance at 435 nm in the measurement of absorbance by UV-Visible spectrophotometer. The interference ions such as Fe(III), Hg (II), Al(III), Co, Cu, Ni, Zn, Ca, Sn, have great effects on the extraction, but they were overcomed by the usage of adequate masking agents before an extraction. At last, a good result was obtained in applying this method to synthetic water.

• Journal of Environmental Health Sciences
• /
• v.38 no.3
• /
• pp.233-240
• /
• 2012

Objectives: The changes in atmospheric $PM_{2.5}$ concentrations were extensively studied in one metropolitan city (Incheon), two small and medium sized cities (Gunsan, Cheonan), and a rural area (Gosan in Jeju). The concentrations of heavy metals (Cr, Mn, Fe, Ni, Cu, Zn, Al, Pb) and the component features of $PM_{2.5}$ were determined for these areas. Methods: This study sampled $PM_{2.5}$ at the designated locations in the metropolitan (Incheon), small and medium sized cities (Gunsan in Jeonbuk and Cheonan in Chungnam), and rural area (Gosan in Jeju) to investigate concentrations with a sampling device (Sequential sampler, APM Eng., Korea). Sampling was undertaken over months, from June 26 to November 26, 2009. Sampling was conducted a total of 44 times, with routine sampling at intervals of six days (24 total times) and intensive sampling (20 total times) during the summer and fall. Mass concentration of $PM_{2.5}$ was evaluated and the concentrations of heavy metals (Cr, Mn, Fe, Ni, Cu, Zn, Al, Pb) were analyzed. Results: The geometric average of concentrations of $PM_{2.5}$ per district was $35.289{\mu}g/m^3$ for Cheonan, $29.955{\mu}g/m^3$ for Incheon, $24.119{\mu}g/m^3$ for Gunsan, and $18.773{\mu}g/m^3$ for Jeju, respectively. The average concentration of $PM_{2.5}$ in Cheonan was the highest. The seasonal concentration distributions per district showed Cheonan $33.387{\mu}g/m^3$, Incheon at $31.550{\mu}g/m^3$, Gunsan $22.900{\mu}g/m^3$, and Jeju $18.900{\mu}g/m^3$ in the summer. For the autumn, the concentrations were $36.873{\mu}g/m^3$ in Cheonan, $28.625{\mu}g/m^3$ in Incheon, $25.227{\mu}g/m^3$ in Gunsan, and $18.667{\mu}g/m^3$ in Jeju. According to the collected data, the concentration showed a tendency to rise during the autumn in all of these regions with the exception of Incheon. For heavy metal distribution per district, Fe showed an elevated concentration during the summer while high concentrations of Pb and Zn occurred during the autumn. Conclusion: These results demonstrated that atmospheric factors affected the concentrations of heavy metals. The results of this study could be used as foundational data for setting environmental air standards focusing on a $PM_{2.5}$ receptor.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.259-261
• /
• 2009

Solar simulator를 이용한 프로판의 수증기 개질은 집광된 태양에너지를 이용하기 위한 목적으로 수행되었다. 본 연구에서는 이와 같은 태양열에너지의 화학적 축열을 실시하기 위해 Solar Simulator를 이용한 메탄의 수증기 개질을 연구하였다. 태양열 모사 램프로 1.24kW급 Xenon-arc lamp를 사용하였다. 반응기는 앞면의 Quartz window와 Absorber로 구성되어 있다. 램프의 빛은 Quartz window를 통하여 촉매층에 직접적으로 방사된다. 프로판의 수증기개질 반응은 고온에서 일어나기 때문에 열에 강한 SiC로 만들어진 Ceramic foam을 Absorber로 사용하였다. 촉매는 Absorber에 Wash-coat하여 사용하였으며, 담지된 촉매는 Ni을 활성성분으로 하는 ICI 46-6와 귀금속 촉매인 Ru/$Al_2O_3$를 사용하였다. 반응기는 SUS 재질로 제작되었으며, 반응기 외부는 Insulation을 하여 열손실을 감소시켰다. Propane과 Steam의 비율은 S/C ratio를 3으로 하여 실험하였다. 실험은 온도와 촉매에 따른 Solar Steam reforming의 반응특성을 분석하였다.

• Economic and Environmental Geology
• /
• v.30 no.5
• /
• pp.417-431
• /
• 1997

Characteristics of sedimentary rocks and enrichment of toxic elements in shale and coal from the Chungnam coal field were investigated based upon geochemistry of major, trace and rare earth elements. Shale and coal of the area are interbedded along the Traissic to the Jurassic Daedong Supergroup, which can be subdivided into grey shale, black shale and coal. The coal had been mined, however all the mines are abandonded due to the economic problems. The shale and coal are characterized by relatively low contents of $SiO_2$, and $Al_2O_3$ and high levels of loss-on-ignition (LOI), CaO and $Na_2O$ in comparison with the North American Shale Composite (NASC). Light rare earth elements (La, Ce, Yb and Lu) are highly enriched with the coal. Ratios of $Al_2O_3/Na_2O$ and $K_2O/Na_2O$ in shale and coal range from 30.0 to 351.8 and from 4.2 to 106.8, which have partly negative correlations against $SiO_2/Al_2O_3$ (1.24 to 6.06), respectively. Those are suggested that controls of mineral compositions in shale and coal can be due to substitution and migration of those elements by diagenesis and metamorphism. Shale and coal of the area may be deposited in terrestrial basin deduced from high C/S (39 to 895) and variable composition of organic carbon (0.39 to 18.40 wt.%) and low contents of reduced sulfur (0.01 to 0.05 wt.%). These shale and coal were originated from the high grade metamorphic and/or igneous rocks, and the rare earth elements of those rocks are slightly influenced with diagenesis and metamorphism on the basis of $Al_2O_3$ versus La, La against Ce, Zr versus Yb, the ratios of La/Ce (0.38 to 0.85) and Th/U (3.6 to 14.6). Characteristics of trace and rare earth elements as Co/Th (0.07 to 0.86), La/Sc (0.31 to 11.05), Se/Th (0.28 to 1.06), V/Ni (1.14 to 3.97), Cr/V (1.4 to 28.3), Ni/Co (2.12 to 8.00) and Zr/Hf (22.6~45.1) in the shale and coal argue for inefficient mixing of the simple source lithologies during sedimentation. These rocks also show much variation in $La_N/Yb_N$ (1.36 to 21.68), Th/Yb (3.5 to 20.0) and La/Th (0.31 to 7.89), and their origin is explained by derivation from a mixture of mainly acidic igneous and metamorphic rocks. Average concentrations in the shale and coal are As=7.2 and 7.5, Ba=913 and 974, Cr=500 and 145, Cu=20 and 26, Ni=38 and 35, Pb=30 and 36, and Zn=77 and 92 ppm, respectively, which are similar to those in the NASC. Average enrichment indices for major elements in the shale (0.79) and coal (0.77) are lower than those in the NASC. In addition, average enrichment index for rare earth elements in coal (2.39) is enriched rather than the shale (1.55). On the basis of the NASC, concentrations of minor and/or environmental toxic elements in the shale and coal were depleted of all the elements examined, excepting Cr, Pb, Rb and Th. Average enrichment indices of trace and/or potentially toxic elements (As, Cr, Cu, Ni, Pb, U and Zn) are 1.23 to 1.24 for shale and 1.06 to 1.22 for coal, respectively.

• Journal of Power System Engineering
• /
• v.6 no.3
• /
• pp.24-30
• /
• 2002

The deformation and fracture behaviors of both Al2O3 and Ni 4.5wt.%Al plasma thermal spray coating were investigated by an acoustic emission method. Plasma thermal spray coating is formed by a process in which melted particles flying with high speed towards substrate, then crash and spread on the substrate surface cooled and solidified in a very short time, stacking of the particles makes coating. A tensile test is conducted on notch specimens in a stress range below the elastic limit of substrate. A bendind test is done on smooth specimens. The waveforms of AE generated from the both test coating specimens can be classified by FFT analysis into two types which low frequency(type I) and high frequency(type II). The type I waveform is considered to corresponds exfoliation of coating layers and type II waveform corresponds the plastic deformation of notch tip. The fracture of the coating layers can estimate by AE event and amplitude, because AE features increase when the deformation generates.