• Korean Journal of Materials Research
• /
• v.23 no.2
• /
• pp.128-134
• /
• 2013

A study on the corrosion behavior of Inconel alloys and Incoloy 800H in molten salt of LiCl-$Li_2O$ was investigated at $650^{\circ}C$ for 24-312 hours in an oxidation atmosphere. The order of the corrosion rate was Inconel 600 < Inconel 601 < Incoloy 800H < Inconel 690. Inconel 600 showed the best performance suggesting that the content of Fe, Cr and Ni are the important factor for corrosion resistance in hot molten salt oxidation conditions. The corrosion products of Inconel 600 and Inconel 601 were $Cr_2O_3$ and $NiFe_2O_4$, In case of Inconel 690, a single layer of $Cr_2O_3$ was formed in the early stage of corrosion and an outer layer of $NiFe_2O_4$ and inner layer of $Cr_2O_3$ were formed with an increase of corrosion time. In the case of Incoloy 800H, $Cr_2O_3$ and $FeCr_2O_4$ were observed. Most of the outer scale of the alloys was observed to be spalled from the results of the SEM analysis and the unspalled scale which adhered to the substrate was composed of three layers. The outer layer, the middle one, and the inner one were Fe, Cr, and Ni-rich, respectively. Inconel 600 showed localized corrosion behavior and Inconel 601, 690 and Incoloy 800H showed uniform corrosion behavior. Ni improves the corrosion resistance and too much Cr and/or Fe content deteriorates the corrosion resistance.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.11
• /
• pp.880-886
• /
• 1991

Multi-layered chip inductors were prepared with good magnetic properties by sintering Ni-Zn-Cu ferrites at a lower temperature. A slurry with 49.5mol%Fe$_{2}O_{3}$, 20.5mol% ZnO, 20mol% NiO and 10nol% CuO was cast into tapes with 60-100\ulcorner of thickness with a doctor blade techniques. The tapes were screen-pronted with 100% silver electrodes, layered and pressed at 250kg/cm$^{2}$ and then sintered ant 900$^{\circ}C$ for 2h. Inductance with internal electrodes printed 5, 10, and 15 turns showed 4.9, 15 and 24$\mu$, respectively, at 1MHz.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.6
• /
• pp.361-365
• /
• 2017

In this paper, we investigated the effect of Co content on the microstructural and electrical properties of $Ni_{0.79}Mn_{2.21-x}Co_xO_4$ (x=0 to 0.25) specimens. Solid-state reaction was used to prepare the bulk specimens. XRD (X-ray diffraction) patterns showed that all compositions had a cubic spinel phase. As a result of the microstructural properties, FE-SEM(field-emission scanning electron microscopy) analysis showed a dense structure, and the mean grain size increased from $5.24{\mu}m$ to $7.33{\mu}m$ with an increase of Co content from x=0 to 0.25. All specimens exhibited the typical NTC thermistor characteristics as the electrical resistance exponentially decreased with increasing temperature. The resistivity and the B-value of $Ni_{0.79}Mn_{1.96}Co_{0.25}O_4$ were $2959{\Omega}{\cdot}cm$ and 3719, respectively.

• Journal of Environmental Health Sciences
• /
• v.24 no.1
• /
• pp.32-37
• /
• 1998

The Carbon Dioxide is the gas, which causes green house effects, unusual changes in the weather, destruction of the life. Almost every nation in the world is trying to search the countermeasure to this poisonous gas. I synthesized $Fe_3O_4$ and NaOH, in order to decompose the Carbon Dioxide. Among the particles synthesizing $Fe_3O_4$, I chose the equivalent ratio 1.00 which can decompose the Carbon Dioxide best, and fixed that equivalent ratio and added the 0.005-3.00 mole percentage of NiCl$_2$ and synthesized $Fe_3O_4$. I studied the decomposition of the Carbon Dioxide and methanized reaction, by measuring its crystal structure, thermochemistrical character and specific surface area. In decomposing the Carbon Dioxide, I used oxygen-deficit Magnetite which I produced by injecting the hydrogen gas into the synthesized sample. I observed the methanization reaction by raising the temperature of sample up to 650$\circ$C and having it reacted with the hydrogen gas. The decomposition of the Carbon Dioxide was added 0.005, 0.03, 0.05 mole percentage of NiCl$_2$ was more effective than pure $Fe_3O_4$. All sample in which the decomposition of the Carbon Dioxide took place produced the methane gas.

• Journal of the Mineralogical Society of Korea
• /
• v.19 no.3 s.49
• /
• pp.163-169
• /
• 2006

Mineralogy and geochemistry of the sediment core from the seamount (2710 m below the sea level) just south of the Antarctic Polar Front were examined to draw paleoceanographic information in glacial-interglacial cycles. Smectite was most abundant clay mineral associated with illite and chlorite. Its content was slightly higher below 170 cm, suggesting a boundary between isotope stage 4 and 5. Si, Zr, Cs, Th, REE, $K_{2}O$, and $Al_{2}O_{3}$ show complete antithetical distribution with respect to $CaCO_{3}$ through the core. $SiO_{2}$ maxima and $CaCO_{3}$ minima at depths of 24, 136, and 176 cm are probably correlated with massive influx of ice-rafted debris during the advance of Antarctic ice shelves. Ni, Cu, and Ba show rather little correlation with $SiO_{2}$, suggesting their relation to biogenic debris, precipitation from seawater, or hydrothermal input. Particularly, Ba maxima tend to lag $10{\sim}20cm$ after $SiO_{2}$ maxima, probably due to rapid increase of productivity following deglaciation.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.689-695
• /
• 2012

We have examined the co-doping effects of 1/2 mol% NiO and 1/4 mol% $Cr_2O_3$ (Ni:Cr = 1:1) on the reaction, microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-$Bi_2O_3-Sb_2O_3$ (ZBS; Sb/Bi = 0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Ni,Cr-doped ZBS, ZBS(NiCr) varistors were controlled using the Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$), ${\alpha}$-spinel ($Zn_7Sb_2O_{12}$), and ${\delta}-Bi_2O_3$ were detected for all of compositions. For the sample with Sb/Bi = 1.0, the Pyrochlore was decomposed and promoted densification at lower temperature by Ni rather than by Cr. A homogeneous microstructure was obtained for all of the samples affected by ${\alpha}$-spinel. The varistor characteristics were not dramatically improved (non-linear coefficient, ${\alpha}$ = 5~24), and seemed to form ${Zn_i}^{{\cdot}{\cdot}}$(0.17 eV) and ${V_o}^{\cdot}$(0.33 eV) as dominant defects. From impedance and modulus spectroscopy, the grain boundaries were found to have been divided into two types, i.e., one is tentatively assigned to ZnO/$Bi_2O_3$ (Ni,Cr)/ZnO (0.98 eV) and the other is assigned to a ZnO/ZnO (~1.5 eV) homojunction.

• Carbon letters
• /
• v.25
• /
• pp.14-24
• /
• 2018

Electrochemical properties and performance of composites performed by incorporating metal oxide or metal hydroxide on carbon materials based on graphene and carbon nanotube (CNT) were analyzed. From the surface analysis by field emission scanning electron microscopy and field emission transmission electron microscopy, it was confirmed that graphene, CNT and metal materials are well dispersed in the ternary composites. In addition, structural and elemental analyses of the composite were conducted. The electrochemical characteristics of the ternary composites were analyzed by cyclic voltammetry, galvanostatic charge-discharge tests, and electrochemical impedance spectroscopy in 6 M KOH, or $1M\;Na_2SO_4$ electrolyte solution. The highest specific capacitance was $1622F\;g^{-1}$ obtained for NiCo-containing graphene with NiCo ratio of 2 to 1 (GNiCo 2:1) and the GNS/single-walled carbon $nanotubes/Ni(OH)_2$ (20 wt%) composite had the maximum specific capacitance of $1149F\;g^{-1}$. The specific capacitance and rate-capability of the $CNT/MnO_2/reduced$ graphene oxide (RGO) composites were improved as compared to the $MnO_2/RGO$ composites without CNTs. The $MnO_2/RGO$ composite containing 20 wt% CNT with reference to RGO exhibited the best specific capacitance of $208.9F\;g^{-1}$ at a current density of $0.5A\;g^{-1}$ and 77.2% capacitance retention at a current density of $10A\;g^{-1}$.

• Journal of the Korean Society of Safety
• /
• v.24 no.4
• /
• pp.22-27
• /
• 2009

In this paper, the minuteness structure, piezoelectric, and dielectric characteristics of $0.95{Pb(Sb_{1/2}Nb_{1/2})_{0.02})_{0.02}(Ni_{1/3}Nb_{2/3})_{0.13}(Zr_{0.48}Ti_{0.52})_{0.85}}O_3+0.05Pb(CO_{1/2}W_{1/2})O_3+0.3%$ $MnO_2+0.3wt%$ CuO ceramics has been systematically investigated as a function of the sintering temperature after manufacturing the specimens with a general method. This study will be very helpful as basic data for developing ceramic materials, More study in a soon time for improving stability of temperature, effect of adds and stability and reality of frequency with improved production condition for specimens will give a powerful potentiality as a applied material of dielectric ceramics.

• Economic and Environmental Geology
• /
• v.30 no.1
• /
• pp.1-14
• /
• 1997

The shales from the Euiseong area are interbedded along the bedding in Cretaceous Gyeongsang Supergroup, which are composed mainly of quartz, plagioclase, K-feldspar and associated with trace amount of biotite, muscovite, chlorite, pyrite, hematite, carbonate and clay minerals. The ratio of $Al_2O_3/Na_2O$ and $K_2O/Na_2O$ in shales from the Shindong Group are ranged from 9.16 to 24.32 and from 1.70 to 5.97, and the Hayang Group ranged from 2.76 to 8.89 and from 0.42 to 2.74, which are negative correlated between $K_2O/Na_2O$ and $Al_2O_3/Na_2O$ against $SiO_2/Al_2O_3$ respectively. Those are suggested that controlled of mineral compositions in shales due to substitution and migration of elements by sedimentation and diagenesis. These shale formation were deposited in basin of terrestrial environments originated from the igneous rocks, and the REE of these rocks are not influenced with diagenesis and hydrothermal alterations on the basis of $Al_2O_3$ versus La, La against Ce, Zr versus Yb, the ratios of La/Ce (0.43 to 0.62) and Th/U (1.11 to 10.71). The narrow range in trace and REE element characteristics as Co/Th (0.63 to 1.92), La/Sc (1.98 to 5.90), Sc/Th (0.58 to 1.30), V/Ni (0.90 to 3.25), Cr/V (0.45 to 1.78), Ni/Co (1.88 to 6.67) and Zr/Hf (30.04~60.87) of these shales argues for inefficient mixing of the simple source lithologies during sedimentation. These rocks also show much variation in $La_N/Yb_N$ (6.90 to 17.02), Th/Yb (4.17 to 13.68) and La/Th (1.98 to 5.90), and their origin is explained by derivation from a mixture of intermediate to acidic igneous rocks.

• Journal of the Korean Society of Tobacco Science
• /
• v.2 no.2
• /
• pp.20-37
• /
• 1980

Among the 34 strains of Nicotinophiles selected in the previous experiments, strain NCT27 identified with Pseudomonas putida and strain NCT30 identified with Arthrobacter oxydans biotype nan thus were Investigated for optimization of growth conditions for nicotine degradation and other cultural characteristics. The compositions of optimized medium were to be following: $KH_2PO_4$ 2.Ogr, KCI 5.Ogr, $MgSO_4$.$7H_2O$ 20mg, $MnSO_4$.$6H_2O$ 0.2mg, $FeSO_4$.$7H_2O$ 1.Omg, Col$^{++}$ (Cobalt Acetate),2.O$\gamma$, N1$^{++}$ (NiSO4,6H2O) 0.5$\gamma$, and yeast extract 80mg per liter. The optimum initial concentrations of nicotine for growth were 0.4% for Pseudomonas and 0.1% for Arthrobacter, respectively. The optimum temperature and pH were 3$0^{\circ}C$ and 7.0 for both of strains. The pH of culture medium of Pseudomonas was changed from acidic condition to basic one in going from the logarithmic growth phase to the stationary growth phase. In contrast with Pseudomonas, it remained constant in case of Arthrobacter. The growth of Arthrobacter was completely inhibited in the nicotine concentration of 0.7&. However, Pseudomonas could grow even in the nicotine concentration of 1.0%. Moreover, it could grow successfully in the tobacco extract media as well as media containing carbon and nitrogen sources other than nicotine. The maximum rates of nicotine degradation were to be 1.22 gr./hr./liter for Pseudomonas and 0.186 gr./hr./liter for Arthrobacter, respectively.