• Resources Recycling
• /
• v.10 no.5
• /
• pp.29-35
• /
• 2001

This study was carried out to recover gold, silver and valuable metals from the printed circuit boards (PCBs) of waste computers. PCBs samples were crushed under 1 mm by a shredder and separated into 30% conducting and loft nonconducting materials by an electrostatic separator. The conducting materials contained valuable metals which were then used as feed materials for magnetic separation. 42% of magnetic materials from the conducting materials was removed by magnetic separation as nonvaluable materials and the others, 58% of non magnetic materials, was used as leaching samples containing 0.227 mg/g Au and 0.697 mg/g Ag. Using the materials of leaching from magnetic separation, more than 95% of copper, iron, zinc, nickel and aluminium was dissolved in 2.0M sulfuric acid solution, added with 0.2M hydrogen peroxide at $85^{\circ}C$. Au and Ag were not extracted in this solution. On the other hand, more than 95% of gold and 100% of silver were leached by the selective leaching with a mixed solvent (0.2M($NH_4$)$_2$$S_2$$O_3$,0.02M $CuSO_4$,0.4M $NH_4$OH). Finally, the residues were reacted with a NaCl solution to leach Pb whereas sulfuric acid was used to leach Sn. Recoveries reached 95% and 98% in solution, respectively.

• Korean Journal of Materials Research
• /
• v.7 no.7
• /
• pp.564-570
• /
• 1997

용융산화에 의한 AI$_{2}$O$_{3}$복합재료의 형성에 미치는 합금원소의 영향을 연구하였다. AI-Mg-3Si 합금이 가장 우수한 산화거동을 보였다. 우수한 3원계로 선정된 AI-1Mg-3Si합금에 제 4원소 Sn, Cu, Ni, Zn을 양을 달리하여 각각 첨가하여 산화거동을 살펴보았다. 1273K, 1373K, 1473K, 에서 20시간 각각 산화실험을 한 결과, 1473K에서는 모든 합금계가 우수했으나 1373K, 1273K에서는 산화가 거의 일어나지 않았다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.2
• /
• pp.394-400
• /
• 2014

In this study, we fabricated ITZO thin films on glass substrates with various RF power from 30 to 60W and investigated the electrical, optical and structural properties. ITZO thin film deposited at 50W exhibited the largest figure of merit ($10.52{\times}10^{-3}{\Omega}^{-1}$) and then its resistivity and sheet resistance were $3.08{\times}10^{-4}{\Omega}-cm$ and $11.41{\Omega}/sq.$, respectively. As results of optical characterization, average transmittance of all ITZO thin films were over 80%. ITZO thin films had amorphous structure regardless of the RF power. The FESEM and AFM results showed that all ITZO thin films have a very smooth surface having no cracks and defects and the film deposited at 50W exhibit the smallest surface roughness of 0.254nm. We found that a amorphous ITZO thin film is a very promising material for replacing ITO in the next display device such as OLED.

• Clean Technology
• /
• v.19 no.4
• /
• pp.416-422
• /
• 2013

In environmental friendly aspects, the synthesis of glycerol carbonate from glycerol using carbon monoxide and oxygen gases which were produced in petrochemical plants was studied. The oxidative carbonylation of glycerol under batch reaction system was performed on parameter conditions such as effect of various metals (Cu, Pd, Fe, Sn, Zn, Cr), oxidizing agents, mole ratio of carbon monoxide to oxygen, catalyst amount, solvent types, reaction temperature and time and dehydrating agents. In particular copper chloride catalysts showed the excellent activities, and the glycerol carbonate yields over CuCl and $CuCl_2$ catalysts were the maximum of 44% and 64%, respectively at the following reaction conditions: solvent as nitrobenzene, mole ratio of 1:3:0.15 (glycerol:carbon monoxide:catalyst), mole ratio of 2:1 (carbon monoxide:oxygen), the total pressure of 30 bar at 413 K for 4 hr. It was found that reactivity were significantly different depending on the oxidation number of Cu catalysts, and oxygen plays an important role as oxidizing agents in producing H2O during oxidation reaction after carbonylation of glycerol.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.4
• /
• pp.734-740
• /
• 2016

The micron-sized indium zinc tin oxide (IZTO) particles were prepared by spray pyrolysis from aqueous precursor solution for indium, zinc, and tin and organic additives such as citric acid (CA) and ethylene glycol (EG) were added to aqueous precursor solution for indium, zinc, and tin. The obtained IZTO particles prepared by spray pyrolysis from the aqueous solution without organic additives had spherical and filled morphologies, whereas the IZTO particles obtained with organic additives had more hollow and porous morphologies. The micron-sized IZTO particles with organic additives were changed fully to nano-sized IZTO particles, whereas the micron-sized IZTO particles without organic additives were not changed fully to nano-sized IZTO particle after post-treatment at $700^{\circ}C$ for 2 hours and wet-ball milling for 24 hours. Surface resistances of micron-sized IZTO's before post-heat treatment and wet-ball milling were much higher than those of nano-sized IZTO's after post-heat treatment and wet-ball milling. From IZTO with composition of 80 wt. % $In_2O_3$, 10 wt. % ZnO, and 10 wt. % $SnO_2$ which showed a smallest surface resistance IZTO after post-heat treatment and wet-ball milling, thin films were deposited on glass substrates by pulsed DC magnetron sputtering, and the electrical and optical properties were investigated.

• Electrical & Electronic Materials
• /
• v.7 no.3
• /
• pp.243-251
• /
• 1994

ITO(Indium Tin Oxide) film with thickness of 1500.angs. was prepared by an e-beam evaporator onto a glass and a p-type InP wafer (100) LEC grown Zn-doped p=2.3*10$\^$16/cm$\^$-3/), in which the components of ITO used for evaporation source were hot pressed pellets 1 mole% ln$\_$2/O$\_$3/+9 mole% SnO$\_$2/, and evaporated in O$\_$2/ ambient. The optimum conditions to preparation of ITO thin film were the substrate temperature of 350.deg. C, the injected oxygen pressure of 2*10$\^$-4/ torr, and the evaporation speed of 0.2-0.3.angs./sec, respectively. In these optimum conditions, the resistivity and the carrier concentration were 5.3*10$\^$-3/ .ohm.-cm, 6.5*10$\^$20/cm$\^$-3/, and the transmittance was over 80%. From the results of J-V measurements in ITO/p-InP structure solar cells, the higher pressure of injected oxygen, the more open circuit voltage. The efficiency of ITO/p-InP solar cell without the grid line contact, prepared by the optimum evaporation conditions, was 7.19%. By using the grid line contact, the efficiency, the open circuit voltage, the short circuit current density, the fill factor, the series resistance, and the shunt resistance were 8.5%, 0.47V, 29.48 mAcm$\^$-2/ , 61.35%, 3.ohm., and 26.6k.ohm., respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.245-245
• /
• 2012

차세대 디스플레이로 각광받고 있는 AMOLED에 대한 관심이 높아짐에 따라 구동 소자의 연구가 활발히 이루어지고 있다. 산화물 반도체 박막 트랜지스터는 비정질 실리콘 박막 트랜지스터에 비해 100 $cm^2$/Vs 이하의 높은 이동도와 우수한 전기적 특성으로 AMOLED 구동 소자로서 학계에서 입증되어왔고, 현재 여러 기업에서 산화물 반도체를 이용한 박막 트랜지스터 제작 연구가 활발히 이루어지고 있다. 본 연구는 열처리 조건을 가변하여 제작한 산화물 반도체 박막 트랜지스터의 전기적 특성 분석을 목적으로 한다. 실리콘 기판에 oxidation 공정을 이용하여 SiO2 100 nm, DC스퍼터링을 이용하여 ITZO (Indium-Tin-Zinc Oxide) 산화물 반도체 박막 50 nm, 증착된 산화물 반도체 박막의 열처리 후, evaporation을 이용하여 source/drain 전극 Ag 150 nm 증착하여 박막 트랜지스터를 제작하였다. 12 sccm의 산소유량, 1시간의 열처리 시간에서 열처리 온도 $400^{\circ}C$, $200^{\circ}C$의 샘플은 각각 이동도 $29.52cm^2/V{\cdot}s$, $16.15cm^2/V{\cdot}s$, 문턱전압 2.61 V, 6.14 V, $S{\cdot}S$ 0.37 V/decade, 0.85 V/decade, on-off ratio 5.21 E+07, 1.10 E+07이었다. 30 sccm의 산소유량, 열처리 온도 $200^{\circ}C$에서 열처리 시간 1시간, 1시간 30분 샘플은 각각 이동도 $12.27cm^2/V{\cdot}s$, $10.15cm^2/V{\cdot}s$, 문턱전압 8.07 V, 4.21 V, $S{\cdot}S$ 0.89 V/decade, 0.71 V/decade, on-off ratio 4.31 E+06, 1.05 E+07이었다. 산화물 반도체의 열처리 효과 분석을 통하여 높은 열처리 온도, 적은 산소의 유량, 열처리 시간이 길수록 이동도, 문턱전압, $S{\cdot}S$의 산화물 박막 트랜지스터 소자의 전기적 특성이 개선되었다.

• Applied Microscopy
• /
• v.45 no.2
• /
• pp.95-100
• /
• 2015

The in-situ heating transmission electron microscopy experiment allows us to observe the time- and temperature-dependent dynamic processes in nanoscale materials by examining the same specimen. The temperature, which is a major experimental parameter, must be measured accurately during in-situ heating experiments. Therefore, calibrating the thermocouple readout of the heating holder prior to the experiment is essential. The calibration can be performed using reference materials whose phase-transformation (melting, oxidation, reduction, etc.) temperatures are well-established. In this study, the calibration experiment was performed with four reference materials, i.e., pure Sn, Al-95 wt%Zn eutectic alloy, NiO/carbon nanotube composite, and pure Al, and the calibration curve and formula were obtained. The thermocouple readout of the holder used in this study provided a reliable temperature value with a relative error of <4%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.2
• /
• pp.99-104
• /
• 2021

Ion-beam sputtering (IBS) was used to deposit semiconducting IZTO (indium zinc tin oxide) thin films onto heavily-doped Si substrates using a sintered ceramic target with the nominal composition In0.4Zn0.5Sn0.1O1.5, which could work as a channel layer for oxide TFT (oxide thin film transistor) devices. The crystallization behavior and electrical properties were examined for the films in terms of deposition parameters, i.e. target tilt angle and substrate temperature during deposition. The thickness uniformity of the films were examined using a stylus profilometer. The observed difference in electrical properties was not related to the degree of crystallization but to the deposition temperature which affected charge carrier concentration (n), electrical resistivity (ρ), sheet resistance (Rs), and Hall mobility (μH) values of the films.

• Analytical Science and Technology
• /
• v.13 no.3
• /
• pp.297-303
• /
• 2000

Isotope-dilution inductively coupled plasma mass spectrometry was used to determine trace amounts of Cd, Cu, Pb, Ni and Zn in sediment. Sediment samples were dissolved by microwave digestion with addition of mixed acid ($HNO_3$, HF and $HClO_4$). Lead was determined after separation of alkaline and alkaline earth metals by an ammonium pyrrolidenedithiocarbarmate (APDC) solvent extraction. The other elements were determined after separation of iron, tin and titanium by hydroxide precipitation. Recovery efficiency of the analyte elements was not satisfactory, but most of matrix elements causing the isobaric interference could be effectively eliminated by the separation. Good agreement was achieved with the certified values in the analysis of the two sediment reference materials.