• The Korean Journal of Ceramics
• /
• v.4 no.2
• /
• pp.72-77
• /
• 1998

A defect model for UO$_2$ fuel containing soluble fission products was devised based on the defect structure of pure and doped uranias. Using the equilibrium between fuel solid-solution and fission-products and the material balance within the fuel, a tracing method to get the stoichiometry change of urania fuel with burnup was made. This tracing method was applied to high burnup urania fuel and DUPIC fuel. The oxygen potential of urania fuel turned out to increase slightly with burnup. The stoichiometry change was calculated to be negligible due to the buffering role f Mo. The oxygen potential of DUPIC fuel out to be sensitive to the initial chemical state of Mo in the fuel.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.10a
• /
• pp.895-896
• /
• 2004

• Nuclear Engineering and Technology
• /
• v.48 no.3
• /
• pp.751-757
• /
• 2016

The present work discusses two different models of boiling water reactor (BWR) bundle to compare the neutronic characteristics of uranium dioxide ($UO_2$) and uranium zirconium hydride ($UZrH_{1.6}$) fuel. Each bundle consists of four assemblies. The BWR assembly fueled with $UO_2$ contains $8{\times}8$ fuel rods while that fueled with $UZrH_{1.6}$ contains $9{\times}9$ fuel rods. The Monte Carlo N-Particle Transport code, based on the Mont Carlo method, is used to design three dimensional models for BWR fuel bundles at typical operating temperatures and pressure conditions. These models are used to determine the multiplication factor, pin-by-pin power distribution, axial power distribution, thermal neutron flux distribution, and axial thermal neutron flux. The moderator and coolant (water) are permitted to boil within the BWR core forming steam bubbles, so it is important to calculate the reactivity effect of voiding at different values. It is found that the hydride fuel bundle design can be simplified by eliminating water rods and replacing the control blade with control rods. $UZrH_{1.6}$ fuel improves the performance of the BWR in different ways such as increasing the energy extracted per fuel assembly, reducing the uranium ore, and reducing the plutonium accumulated in the BWR through burnup.

• Nuclear Engineering and Technology
• /
• v.40 no.3
• /
• pp.191-198
• /
• 2008

The influence of fission products' contents on the DUPIC fuel powder and pellet properties was experimentally evaluated using SIMFUEL as a surrogate for actual spent PWR fuel due to the high radioactivity of spent fuel. Pure $UO_2$ and SIMFUEL pellets with fission products equivalent to a burn-up of 35,000 MWd/tU and 60,000 MWd/tU were used as impurities in this study. The specific surface area of the powder milled after the OREOX treatment increased and resulted in sintered pellets with a theoretical density (TD) higher than 95%, regardless of the impurity contents. However, the grain size of the sintered pellets decreased with the increasing impurity contents. As a result of the dissolved oxides in $UO_2$ from the impurity groups, the specific surface area of the OREOX powder increased with an increase of the impurities. The grain size of the sintered pellets was significantly decreased by the metallic and oxide precipitates.

• Nuclear Engineering and Technology
• /
• v.30 no.6
• /
• pp.541-554
• /
• 1998

A computer code COSMOS has been developed based on the CARO-D5 for the thermal analysis of LWR UO$_2$ and MOX fuel rod under steady-state and transient operating conditions. The main purpose of the COSMOS, which considers high turnup characteristics such as thermal conductivity degradation with turnup and rim formation at the outer part of fuel pellet, is to calculate temperature profile across fuel pellet and fission gas release up to high burnup. A new mechanistic fission gas release model developed based on physical processes has been incorporated into the code. In addition, the features of MOX fuel such as change in themo-mechanical properties and the effect of microscopic heterogeneity on fission gas release have been also taken into account so that it can be applied to MOX fuel. Another important feature of the COSMOS is that it can analyze fuel segment refabricated from base irradiated fuel rods in commercial reactors. This feature makes it possible to analyze database obtained from international projects such as the MALDEN and RISO, many of which were collected from refabricated fuel segments. The capacity of the COSMOS has been tested with some number of experimental results obtained from the HALDEN, RISO and FIGARO programs. Comparison with the measured data indicates that, although the COSMOS gives reasonable agreement, the current models need to be improved. This work is being performed using database available from the OECD/NEA.

• Nuclear Engineering and Technology
• /
• v.50 no.2
• /
• pp.268-279
• /
• 2018

The ALCYONE multidimensional fuel performance code codeveloped by the CEA, EDF, and AREVA NP within the PLEIADES software environment models the behavior of fuel rods during irradiation in commercial pressurized water reactors (PWRs), power ramps in experimental reactors, or accidental conditions such as loss of coolant accidents or reactivity-initiated accidents (RIAs). As regards the latter case of transient in particular, ALCYONE is intended to predictively simulate the response of a fuel rod by taking account of mechanisms in a way that models the physics as closely as possible, encompassing all possible stages of the transient as well as various fuel/cladding material types and irradiation conditions of interest. On the way to complying with these objectives, ALCYONE development and validation shall include tests on $PWR-UO_2$ fuel rods with advanced claddings such as M5(R) under "low pressure-low temperature" or "high pressure-high temperature" water coolant conditions. This article first presents ALCYONE V1.4 RIA-related features and modeling. It especially focuses on recent developments dedicated on the one hand to nonsteady water heat and mass transport and on the other hand to the modeling of grain boundary cracking-induced fission gas release and swelling. This article then compares some simulations of RIA transients performed on $UO_2$-M5(R) fuel rods in flowing sodium or stagnant water coolant conditions to the relevant experimental results gained from tests performed in either the French CABRI or the Japanese NSRR nuclear transient reactor facilities. It shows in particular to what extent ALCYONE-starting from base irradiation conditions it itself computes-is currently able to handle both the first stage of the transient, namely the pellet-cladding mechanical interaction phase, and the second stage of the transient, should a boiling crisis occur. Areas of improvement are finally discussed with a view to simulating and analyzing further tests to be performed under prototypical PWR conditions within the CABRI International Program. M5(R) is a trademark or a registered trademark of AREVA NP in the USA or other countries.

• Nuclear Engineering and Technology
• /
• v.48 no.1
• /
• pp.1-15
• /
• 2016

For a long time, a top priority in the nuclear industry was the safe, reliable, and economic operation of light water reactors. However, the development of accident-tolerant fuel (ATF) became a hot topic in the nuclear research field after the March 2011 events at Fukushima, Japan. In Korea, innovative concepts of ATF have been developing to increase fuel safety and reliability during normal operations, operational transients, and also accident events. The microcell $UO_2$ and high-density composite pellet concepts are being developed as ATF pellets. A microcell $UO_2$ pellet is envisaged to have the enhanced retention capabilities of highly radioactive and corrosive fission products. High-density pellets are expected to be used in combination with the particular ATF cladding concepts. Two concepts-surface-modified Zr-based alloy and SiC composite material-are being developed as ATF cladding, as these innovative concepts can effectively suppress hydrogen explosions and the release of radionuclides into the environment.

• Nuclear Engineering and Technology
• /
• v.52 no.4
• /
• pp.674-680
• /
• 2020

We used MCNP6 computer code to model HTR-10 core reactor. We used two types of fuel; UO₂ and (Th+Pu)O₂ mixture. We determined the critical height at which the reactor approached criticality in both two cases. The neutronic and burnup parameters were investigated. The results indicated that the core fueled with mixed (Th+Pu)O₂, achieved about 24% higher fuel cycle length than the UO₂ case. It also enhanced safeguard security by burning Pu isotopes. The results were compared with previously published papers and good agreements were found.

• Nuclear Engineering and Technology
• /
• v.50 no.2
• /
• pp.259-267
• /
• 2018

Focused ion beam-scanning electron microscope and electron backscattered diffraction examinations were conducted in the center of a $73\;GWd/t_U\;UO_2$ fuel. They showed the formation of subdomains within the initial grains. The local crystal orientations in these domains were close to that of the original grain. Most of the fission gas bubbles were located on the boundaries. Their shapes were far from spherical and far from lenticular. No interlinked bubble network was found. These observations shed light on previous unexplained observations. They plead for a revision of the classical description of fission gas release mechanisms for the center of high burn-up $UO_2$. Yet, complementary detailed observations are needed to better understand the mechanisms involved.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.05a
• /
• pp.401-402
• /
• 2005