• Progress in Superconductivity
• /
• 제5권1호
• /
• pp.75-79
• /
• 2003

YBCO films were deposited with various thicknesses from 100nm to 1.6$\mu\textrm{m}$ on single crystal $SrTiO_3$ substrates by pulsed laser deposition (PLD). The effects of different deposition conditions, especially different deposition rates by means of changing the pulsed laser frequency up to 200Hz, on the J$_{c}$ value were studied. For YBCO film with the thickness of 200nm, the $J_{c}$ value of $2.1MA/\textrm{cm}^2$ has been achieved under the high deposition rate of 3.2nm/s (190nm/min). The $J_{c}$ can be maintained greater than $1M/\textrm{cm}^2$ with the thickness less than 1$\mu\textrm{m}$. The X-ray analysis was used to examine the texture, crystallization and surface quality. The SEM was employed to analyze the surface of YBCO, and it was shown the surface of YBCO film became rougher with increasing the thickness. There were many large singular outgrowths and networks of outgrowths on the surface of YBCO films which lowered the density of thick YBCO film. The outgrowth network was probably the a-axis YBCO corresponding to XRD $\theta$-2$\theta$scan and $\chi$-scan which were used to characterize a-axis orientation of YBCO film. The reason for J$_{c}$ declining with increasing the thickness was studied and discussed.sed.

• 한국전기전자재료학회논문지
• /
• 제13권4호
• /
• pp.312-317
• /
• 2000

Ferroelectric S $r_{0.9}$/B $i_{2.1}$/T $a_{2}$/ $O_{9}$ solutions were synthesized using sol-gel process in which strontinum ethoxide bismuth ethoxide trantalum ethoxide were used a s startring materials. SBT thin films were coated on Pt/Ti/ $SiO_2$/Si substrates by spin-coating. rapid thermal annealing (RTA) was used to promote crystallization. Thin films were annealed at $700^{\circ}C$ for 1 hr in an oxygen atmosphere. This temperature is about 10$0^{\circ}C$ lower than the usual annealing temperature for SBT thin films. Pt top-electrode was deposited by sputtering and thin films were post-annealed at $700^{\circ}C$ for 30 min. to enhance electrical properties. As the RTA temperature increased the higher 2 $P_{r}$ values were obtained. At RTA temperature being 78$0^{\circ}C$ remanent polarization of S $r_{0.9}$/B $i_{2.1}$/T $a_{2}$/ $O_{9}$ thin film was 7.73 $\mu$C/cm $_2$ and the leakage current density was 1.14$\times$10$^{-7}$ A/c $m^2$ at 3 V. As RTA temperature increased the breakdown voltage was decreased. It is considered that the low-field breadown is caused by the rough surface of SBT films and forming bismuth metal in SBT thin films.films.lms.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.566-569
• /
• 2002

The $(Sr_{0.9}Ca_{0.1})TiO_3$(SCT) thin films are deposited on Pt-coated electrode (Pt/TiN/$SiO_2$/Si) using RF sputtering method. The maximum dielectric constant of SCT thin film is obtained by annealing at $600[^{\circ}C]$. The temperature properties of the dielectric loss have a value within 0.02 in temperature ranges of $-80{\sim}+90[^{\circ}C]$. The capacitance characteristics had a stable value within ${\pm}4[%]$. The drastic decrease of dielectric constant and increase of dielectric loss in SCT thin films is observed above 200[kHz].

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.623-626
• /
• 2004

[ $Ba_{0.6}Sr_{0.4}TiO_3$ ] (BST) dielectric thin films doped by Cr were prepared using an alkoxide-based sol-gel method on the Pt/Ti/SiO2/Si substrate. Atomic force microscopy and x-ray diffraction analysis showed that increasing the Cr doping ratio causes increased grain size while the surface remains smooth and crack-free. It was also found that compared with undoped films the increase of Cr content in BST improves the dielectric constant and the leakage-current characteristics. The figure of merit reached the maximum value of 72.3 at the 5 mol % of Cr doping. This composition showed the dielectric constant of 426, the loss factor of 0.0065, tenability of 47.7%, and leakage-current density (at the electric field of 100 kV/cm) of $5.31{\times}10^{-8}A/cm^2$. The results show that the Cr-doped BST thin films are prospective candidates for applications in tunable devices.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.171-172
• /
• 2008

$(Ba_{0.57}Sr_{0.33}Ca_{0.10})TiO_3$ (BSCT) thick films doped with 0.1 mol% $MnCO_3$ and $Yb_2O_3$ ($0.1{\sim}0.7$ mol%) were fabricated by the screen printing method on the alumina substrate. And the structural and electrical properties as a function of $Yb_2O_3$ amount were investigated. The lattice constants of the BSCT thick film doped with 0.1 mol% is 0.3955 nm. The specimen doped with 0.7 mol% $Yb_2O_3$ showed dense and uniform grains with diameters of about 6.3 mm. The thickness of all BSCT thick films was approximately 60 mm. The Curie temperature of the BSCT specimen doped with 0.1 mol% $Yb_2O_3$ was $18^{\circ}C$, and the dielectric constantand dielectric loss at this temperature was 4637 and 4.2%, respectively. The BSCT specimen doped with 0.1 mol% $Yb_2O_3$ showed the maximum value of $349{\times}10^{-9}C/cm^2K$ at Curie temperature. The figure of merit $F_D$ for specific detectivity of the specimens doped with 0.1 mol% $Yb_2O_3$ showed the highest value of $10.9{\times}10^{-9}Ccm/J$.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권10호
• /
• pp.559-563
• /
• 2000

The $(Sr_{1-x}Ca_x)TiO_3(SCT)$ thin films are deposited on Pt-coated(Pt/TiN/$SiO_2$/Si) using RF sputtering method with substitutional contents of Ca. The maximum grain of thin films is obtained by substitution of Ca at 15[mol%]. Also the composition of SCT thin films were closed to stoichiometry(1.081∼1.117 in A/B/ ratio). The dielectric constant was increased with increasing the substitutional contents of Ca, while it was decreased if the substitutional contents of Ca exceeded over 15[mol%]. The dielectric constant changes almost linearly in temperature ranges of -80∼+90[^${\circ}C$]. The temperature properties of the dielectric loss have a stable value within 0.02 independent of the substitutional contents of Ca. All SCT thin films used in this study show the phenomena of dielectric relaxation with the increase of frequency, and the relaxation frequency is observed above 2000[kHz]. The current-voltage characteristics of SCT15 thin films showed the increasing leakage current as the measuring temperature increase.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2012년도 임시총회 및 하계학술연구발표회
• /
• pp.121-122
• /
• 2012

Iron-excess gallium ferrite, $Ga_{0.6}Fe_{1.4}O_3$ (GFO), is known to have room-temperature ferromagnetic phases and potentially exhibit ferroelectricity as well [1]. But, leaky polarization-electric field (PE) hysteresis curves of the GFO thin film are hurdle to prove its spontaneous polarization, in other words, ferroelecticity. One of the reasons that the GFO films have leaky PE hysteresis loop is carrier hopping between $Fe^{2+}$ and $Fe^{3+}$ sites due to oxygen deficiency. We focus on reducing conducting current by substituting divalent cations at $Fe^{2+}$ sites. GFO thin films were grown epitaxially along b-axis normal to $SrRuO_3/SrTiO_3$ (111) substrates by pulsed laser deposition. Current density of the ion-substituted GFO thin films was reduced by $10^3$ or more. Ferroelectric properties of the ion-substituted GFO thin films were measured using macroscopic and microscopic schemes. In particular, local ferroelectric properties of the GFO thin films were exhibited and their remnant polarization and piezoelectric d33 coefficient were obtained.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1279_1280
• /
• 2009

Vanadium dioxide(VO2) has been reported to be the most attractive material for thermochromic windows due to its semiconductor-metal phase transition at around $68^{\circ}C$. However, our previous experiment showed it is difficult to grow VO2 thin films directly on glass substrate, whereas thermochromic VO2 thin films were successfully grown on R-cut sapphire substrate. Properties of VO2 thin films on different orientations of sapphire substrates were already reported. Furthermore, VO2 thin films were successfully grown heteroepitaxially on (001) preferred oriented ZnO coated glass. We deposited VO2 thin films using V2O5 targets on substrates with various lattice parameters with same orientation(SrTiO3, MgO, and Sapphire substrate of (001) orientation) by pulsed laser deposition. In this work, we will discuss the effects of lattice misfit, substrate-induced stress and grain size on the properties of VO2 thin films deposited on various substrate materials.

• 한국초전도ㆍ저온공학회논문지
• /
• 제19권3호
• /
• pp.13-17
• /
• 2017

We investigated the effect of self-assembled BSO nano-defects as pinning centers in BSO-added GdBCO films when the thicknesses of films were varied. 3.5 vol. % BSO-added GdBCO films with varying thicknesses from 200 nm to 1000 nm were deposited on $SrTiO_3$ (STO) substrate by using pulsed laser deposition (PLD) process. For the films with thicknesses of 400 nm and 600 nm, 'anomaly shoulders' in $J_c-H$ characteristic curves were observed near the matching field. The anomaly shoulders appeared in the field dependence of $J_c$ may be attributed to the existence of double pinning mechanisms in thin films. The fit to the pinning force density as a function of reduced field h ($H/H_{irr}$) using the Dew-Hughes' scaling law shows that both the 400 nm- and the 600 nm-thick films have double pinning mechanisms while the other films have a single pinning mechanism. These results indicate that the self-assembled property of BSO result in different role as pinning centers with different thickness.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.213-214
• /
• 2008

The $Sr_{0.7}Bi_{2.3}Nb_2O_9$(SBN) thin films are deposited on Pt-coated electrode(Pt/Ti/SiO2/Si) using RF sputtering method at various substrate temperature. The optimum conditions of RF power and Ar/O2 ratio were 60[W] and 70/30, respectively. The crystallinity of SBN thin films were increased with increase of substrate temperature in the temperature range of 100~400[$^{\circ}C$]. The capacitance of SBN thin films were increased with the increase of substrate temperature.