• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.10
• /
• pp.1117-1123
• /
• 2014

This study sintered $Si_3N_4$ with different amounts of $SiO_2$ nano-colloid. The surface of a mirror-polished specimen was coated with $SiO_2$ nano-colloid, and cracks were healed when the specimen was treated at a temperature of 1273 K for 1 h in air. Wear specimen experiments were conducted after heat treatments for 10 min at 1073, 1273, and 1573 K. The heat-treated surface that was coated with the $SiO_2$ nano-colloid was slightly rougher than the noncoated surface. The oxidation state of the surface according to the heat treatment temperature showed no correlation with the surface roughness. Moreover, the friction coefficient, wear loss, and bending strength were not related to the surface roughness. $Si_3N_4$ exhibited an abrasive wear behavior when SKD11 was used as an opponent material. The friction coefficient was proportional to the wear loss, and the bending strength was inversely proportional to the friction coefficient and wear loss. The friction coefficient and wear loss increased with increasing amounts of the $SiO_2$ nanocolloid. In addition, the friction coefficient was slightly increased by increasing the heat treatment temperature.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.3
• /
• pp.267-272
• /
• 2011

We analyzed the wear characterization of $Si_3N_4$ ceramics according to the amount of added $SiO_2$ nanocolloid. The test specimen was prepared by hot-press sintering at 35 MPa and 2123 K in an $N_2$ gas atmosphere for 1 h. A wear test was performed with a block-on-ring tester, and the test conditions were as follows: (1) the ring with a diameter of 35 mm had a rotational speed of 50 rpm; (2) the load was 9.8 N; and (3) the temperature was $25^{\circ}C$. The test results show that $Si_3N_4$ ceramics have a friction coefficient of about 1.0 and a wear loss of about 0.02 mm. Of the specimens used this study, the test specimen with 1.3 wt% of added $SiO_2$ nanocolloid has the best wear resistance because it has the lowest friction coefficient and the smallest wear loss. This specimen also has the highest Vickers hardness and bending strength. In this study, the friction coefficient is inversely proportional to the hardness and bending strength.

• Journal of the Korean Ceramic Society
• /
• v.41 no.4
• /
• pp.297-301
• /
• 2004

Nano-sized mullite (3Al$_2$O$_3$$.$2SiO$_2$) colloids were prepared by use of the spray combustion method. For combustion reaction, Al(NO$_3$)$_3$$.$9$H_2O$, and CH$_{6}$N$_4$O were used as an oxidizer and a fuel respectively, and then colloidal silica was also added as 2SiO$_2$source for mullite. The temperature of the reaction chamber was kept at 80$0^{\circ}C$ to initiate the ignition of droplets of the mixed precursors. For preventing droplet coagulation, the droplet number concentration was reduced using the metal screen filter, and the residence time of aerosol was kept at 2.5 seconds for laminar flow. The synthesized colloidal particles had an uniform spherical shape with 130 nanometer size and the crystalline phase showed the mullite with stoichiometry in the observations of XRD and TEM.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.241-241
• /
• 2003

실리카 나노 분말의 제조공정과 얻어진 나노분말의 자기조립 현상에 대하여 연구하였다. 나노분말은 TEOS(Tetraethylorthosilicate)를 이용하여 Stober process로 단분산 콜로이드 SiO2를 제조하였다. 다양한 응용을 위해서 좁은 입도분포를 가지면서도 다양한 크기를 가지는 분말을 제조하고자 TEOS, NH4OH, 에탄올, 증류수 등의 절대량과 몰비를 변화시키면서 나노분말을 제조하였다. 실험조건에 대한 입도분포와 평균 입자크기의 변화는 핵생성 이론으로 설명될 수 있었다. 얻어진 나노분말을 이용하여 dipcoating과 electron plating방법으로 단층 혹은 여러층의 박막을 형성하였다. 자기배열에 기초한 두 가지 증착방법에서 박막층에 미치는 변수들의 영향을 주로 electorn plating 방법에 대하여 고찰하였다.

• Journal of the Mineralogical Society of Korea
• /
• v.19 no.4 s.50
• /
• pp.231-238
• /
• 2006

Transports of heterogeneously charged particles were investigated based on column experiments. Synthesized mono-dispersed ferrihydrite (${\sim}100nm$) and amorphous $SiO_2\;({\sim}40nm\;and\;{\sim}80nm)$ particles, of which surfaces are oppositely charged under pH < 9.0 (ferrihydrite, positive; amorphous silica, negative), were used. $177{\sim}250{\mu}m$ quartz sand was used as a stationary matrix. The results show that even favorable particles (i.e., ferrihydrite) can show a conservative transport through the oppositely charged media (i.e., quartz) when they coexist with humic acid or with much greater number of oppositely charged particles. These results imply that transports of both negatively and positively charged contaminants may be possible at the same time under a condition of heterogeneous colloidal system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.1-11
• /
• 2016

The effect of the migration of nanoparticles near the wall of a channel on the convective heat transfer in a laminar flow of $SiO_2$ nanoparticle suspensions (nanofluids) under constant wall heat flux boundary conditions was numerically and experimentally investigated in this study. The dynamic thermal conductivity of the aqueous $SiO_2$ nanofluids was measured using T-type thermocouples attached to the outer surface of a stainless steel circular tube (with a length of 1 m and diameter of 1.75 mm). The nanofluids used in this study were synthesized by dispersing $SiO_2$ spherical nanoparticles with a diameter of 24 nm in de-ionized water (DIW). The enhancement of the thermal conductivity of the nanofluids (e.g., an increase of up to 7.9 %) was demonstrated by comparing the temperature profiles in the flow of the nanofluids with that in the flow of the basefluids (i.e., DIW). However, this trend was not demonstrated in the computational analysis, because the numerical models were based on continuum assumptions and flow features involving nanoparticles in a stable colloidal solution. Thus, to explore the non-continuum effects, such as the modification of the morphology caused by nanoparticle-wall interactions on the heat exchanging surfaces (e.g., the isolated and dispersed precipitation of the nanoparticles), additional experiments were performed using DIW right after the measurements using the nanofluids.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1715-1720
• /
• 2010

In this study, we analyzed the crack-healing characteristics of specimens; different crack lengths and coating methods of $Si_3N_4$ ceramic structures with long cracks were analyzed. Cracks with lengths of about $100-500\;{\mu}m$ were obtained using a Vickers indenter for a load of 24.5-98 N. In the case of a crack obtained by applying a load of 24.5 N, the crack-healed specimen with $SiO_2$ nanocolloid coating exhibited the highest bending strength, which was higher than that of a smooth specimen by 140%, but the bending strength of a crack-healed specimen that had a $SiO_2$ nanocolloid coating and originally had multiple cracks was lower than that of a smooth specimen. However, when compared to the cracked specimens, the bending strength of most specimens with multiple cracks increased slightly. On the basis of these results, the crack-healing characteristics of $Si_3N_4$ ceramic structures with multiple indentations were studied for different coating methods. The most effective coating method for long-crack specimens was hydrostatic pressure coating.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.30 no.3
• /
• pp.5-12
• /
• 2022

This study suggests the effective recycling method of sludge waste from various industrial fields to synthesize uniform colloidal silica nanoparticles. In detail, polymers are removed from the sludge waste to attain sludge-extracted silica (s-SiO₂) micron-sized particles, and ammonia assisted sonication is applied to s-SiO₂, which has effectively extracted the silanol precursor. The nano-sized silica (n-SiO₂) particles are successfully synthesized by a typical sol-gel method using silanol precursor. Also, the yield amounts of n-SiO₂ are determined by the function of s-SiO₂ etching time. Finally, n-SiO₂-based slurry is synthesized for the practical CMP application. As a result, rough-surfaced semiconductor chip is successfully polished by the n-SiO₂-based slurry to exhibit the mirror-like clean surface. In this regard, sludge wastes are successfully prepared as valuable semicondutor grade materials.

• Journal of ILASS-Korea
• /
• v.8 no.1
• /
• pp.16-22
• /
• 2003

Zeta potential measurements of colloid particles suspended in a liquid are performed by a Zeta Meter developed. There are many applications of colloid stability in spray technology, paints, wastewater treatment, and pharmaceuticalse. Zeta potentials of charged particles are obtained by measuring the electrophoretic velocities of the particles using video enhanced microscopy and image analysis program. The values of zeta potential of polystyrene latex(PSL), $silica(SiO_2)$M, polyvinylidence difluoride(PVDF), silicon nitride, and alumina particles in deionized (DI) water were measured to be -40.5, -31.9, -25.2, -15.1 and -10.1mV, respectively. The particles having high zeta potential less than -20 mV are stable in DI water, because the double layers of them have strong repulsive forces mutually, and the particles having low zeta potential over -20mV are unstable due to Van Der Waals forces. Silica(>20nm), PSL, aluminum and PVDF particles were found to be stable that would remain separate and well disperse, while silicon nitride and alumina particles were found to be unstable that would gradually agglomerate in DI water.