• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.3
• /
• pp.263-267
• /
• 2007

We investigate the influence of the ambient gas during thermal annealing on the photoluminescence (PL) properties of europium-silicate thin films. The films were fabricated on substrates by using a radio-frequency magnetron sputtering method and subsequent rapid thermal annealing (RTA). The mechanism for the formation of the europium silicates during the annealing process was investigated by using X-ray diffraction (XRD) spectroscopy, Auger electron spectroscopy (AES) and transmission electron microscopy (TEM). A series of narrow PL spectra from $Eu^{3+}$ ions was observed from the film annealed in $O_2$ ambient. Broad PL spectra associated with $Eu^{2+}$ ions, with a maximum intensity at 600 nm and a FWHM of 110 nm, were observed from the thin film annealed at $1000^{\circ}C$ in $N_2$ ambient.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.3
• /
• pp.119-122
• /
• 2011

A series of mesoporous silicalites was synthesized using different compositions of tetraethylorthosilicate and methyltriethoxysilane (MTES) as the silica source. Cetyltrimethylammonium bromide was used as the organic template. Their detailed pore structures were investigated by transmission electron microscopy, X-ray diffraction, and N2 adsorption method. The thermal properties of these silicalites were studied by thermogravimetric analysis. The increased amount of MTES destroyed mesoporous channels and reduced pore sizes from 3.4 nm to 2.8 nm in calcined silicalites. The calcined silicalite transformed completely into an amorphous state at 30% MTES loading. Methyl pending groups of MTES hindered the structural ordering of ≡Si-O- frameworks, resulting in an amorphous structure. This was caused by the insufficient formation of supramolecular assembly with the organic template. No capillary condensation step was found in MS 7/3 silicalite. The other capillary condensation steps shifted toward the lower relative pressure with increasing MTES content, indicating the reduction of pore sizes.

• Journal of Surface Science and Engineering
• /
• v.29 no.6
• /
• pp.788-796
• /
• 1996

$TiO_2$ films prepared by RF magnetron sputtering, electron beam evaporation, ion assisted deposition (IAD) and sol-gel method are prepared on c-Si substrate and vitreous silica substrate respectively. From the transmission spectra of $TiO_2$ films on vitreous silica substrate in the spectral region from 190 nm to 900 nm, k($\lambda$) of $TiO_2$ is obtained. Using k($\lambda$) in the interband transition region the coefficients of the quantum mechanical dispersion relation of an amorphous $TiO_2$ and hence n($\lambda$) including the optically opaque region of above fundamental transition energy are obtained. The spectroscopic ellipsometry spectra of $TiO_2$ films in the spectral region of 1.5-5.0eV are model analyzed to get the film packing density variation versus i) substrate material, ii) film thickness and iii) film growth technique. The complex refractive index change of these $TiO_2$ films versus water condensation is also studied. Film micro-structures by SE modelling results are compared with those by atomic force microscopy images and X-ray diffraction data.

• Asian Journal of Atmospheric Environment
• /
• v.11 no.1
• /
• pp.54-60
• /
• 2017

Quantifying the trace elements in infinitesimal ambient liquid samples (e.g., single raindrop, cloud/fog water, and the soluble fraction extracted from the particles collected for a short time) is an important task for understanding formation processes, heating/cooling rates, and their health hazards. The purpose of this study is to employ an in-air micro PIXE system for quantitative analysis of the trace elements in a thimbleful of reference liquid sample. The bag type liquid sample holder originally designed with $10{\mu}m$ thick $Mylar^{(R)}$ film retained the original shape without any film perforation and apparent peaks of film blank by the end of the analysis. As one of tasks to be solved, the homogeneity of the elemental distribution in liquid reference species was verified by the X-ray line profiles for several references. It was possible to resolve the significant peaks for whole target elements corresponding to the channel number of micro-PIXE spectrum. The calibration curves for the six target elements (Si, S, Cl, Fe, Ni, and Zn) in standard solutions were successfully plotted by concentration (ppm) and ROI of interest net counts/dose (nC).

• Progress in Superconductivity
• /
• v.9 no.2
• /
• pp.162-166
• /
• 2008

We are developing a sensitive gamma ray spectrometer based on superconducting transition edge sensors. The detector consists of a small piece of high purity Sn as an absorber and a Ti/Au bilayer as a temperature sensor. It is designed to measure the thermal signal caused by absorption of gamma rays. The mechanical support and the thermal contact between the absorber and the thermometer were made with Stycast epoxy. The bilayer was formed by e-beam evaporation and patterned by wet etching on top of a $SiN_X$ membrane. A sharp superconducting transition of the film was measured near 100 mK. When the film was biased to the edge of the transition, signals were observed due to single photon absorption emitted from an $^{241}Am$ source. The measured spectrum showed several characteristic peaks of the source including 59.5 keV gamma line. The full with at half maximum was about 900 eV for the 59.5 keV gamma line. The background was low enough to resolve low energy lines. Considerations to improve the energy resolution of the gamma ray spectrometer are also discussed.

• Journal of Powder Materials
• /
• v.22 no.6
• /
• pp.391-395
• /
• 2015

We report on the successful fabrication of ZnO nanorod (NR)/polystyrene (PS) nanosphere hybrid nanostructure by combining drop coating and hydrothermal methods. Especially, by adopting an atomic layer deposition method for seed layer formation, very uniform ZnO NR structure is grown on the complicated PS surfaces. By using zinc nitrate hexahydrate $[Zn(NO_3)_2{\cdot}6H_2O]$ and hexamine $[(CH_2)_6N_4]$ as sources for Zn and O in hydrothermal process, hexagonal shaped single crystal ZnO NRs are synthesized without dissolution of PS in hydrothermal solution. X-ray diffraction results show that the ZnO NRs are grown along c-axis with single crystalline structure and there is no trace of impurities or unintentionally formed intermetallic compounds. Photoluminescence spectrum measured at room temperature for the ZnO NRs on flat Si and PS show typical two emission bands, which are corresponding to the band-edge and deep level emissions in ZnO crystal. Based on these structural and optical investigations, we confirm that the ZnO NRs can be grown well even on the complicated PS surface morphology to form the chestnut-shaped hybrid nanostructures for the energy generation and storage applications.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.9
• /
• pp.1409-1418
• /
• 1990

Characteristics of NMOS transistors with phosphorus source/drain junctions formed by two-step rapid thermal diffusion (RTD) process using a solid diffusion source have been investigated. Phosphorus profiles after RTD were measured by SIMS analysis. In the case of 1100\ulcorner, 10sec RTD of, P, the specific contact resistance of n+ Si-Al was 2.4x10**-7 \ulcorner-cm\ulcorner which is 1/5 of the As junction The comparison fo P junction devices formed by RTD and conventional As junction devices shows that both short channel effect and hot carrier effect of P junction devices are smaller than those of As junction devices when the devices have same junction depths. P junction device had maximum of 0.4 times lower Isub/Id than As junction device. Characteristics of P junction formed by several different RTD conditions have been compared and 1000\ulcorner RTD sample had the smaller hot carrier generation. Also, it has been shown that the hot carrier generation can be futher reduced by forming the P junctions by 3-step RTD which has RTO-driven-in process additionally.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.581-581
• /
• 2013

ITO (Indium Tin oxide)는 비화학 양론적 조성을 띄는 n-type 반도체 특성이 있으며 가시광 영역(380~780 nm)의 파장에 대한 높은 광 투과도(>85%)를 가지며 비교적 높은 전도도(${\sim}10^4/{\Omega}-cm$)를 갖고 화학적 안정성이 우수하여 투명전극 박막으로 많이 사용되어왔다. 또한, PET film은 전기절연성, 내후성이 우수하고, 85%의 투과율을 보이는 특성에 의하여 Flexible display의 기판으로 많은 연구가 진행되고 있다. 이와 같은 PET film에 ITO를 증착하여 광 투과도와 전기전도도가 우수한 Flexible display의 투명전극으로 많은 연구 개발이 이루어지고 있다. Flexible ITO 박막의 특성을 향상하기 위해서는 $200^{\circ}C$ 이상의 열처리 공정이 필요하지만, PET는 약 $200^{\circ}C$ 이상에서 열 변형이 일어나므로 열처리 공정이 어렵고 이러한 문제점을 해결하기 위해 ITO/PET film에서 PET film의 변형 없이 ITO 박막의 표면에 전자빔 형태로 조사하여 박막의 물성을 개선하는 연구가 진행되고 있다 [1]. 본 연구에서는 ITO/$SiO_2$가 증착된 PET film에 전자빔을 조사하여 ITO 박막의 물성 변화를 관찰하였고, 전자빔 에너지 변화 및 전자빔 조사 시간에 따라 ITO film의 전기적, 광학적 특성 변화를 분석하였다. 구조적 특성은 XRD (X-ray diffraction), 전기적 특성은 4-point probe, Hall measurement를 이용하였으며, 가시광영역의 광 투과도는 UV-Vis spectrometer로 측정하였다. 전기 광학적 특성 변화는 Figure of Merit (FOM) 수치로 분석하였다. 이 실험으로 PET film에 직접적인 열을 가하지 않으면서 ITO 박막의 표면에 전자빔을 조사 하여, 박막의 전기전도도 및 광 투과율, 결정성 향상 등을 관찰할 수 있었다.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.3
• /
• pp.144-148
• /
• 2012

In this work, we investigated to the etching characteristics of $TiO_2$ thin film and the selectivity using the inductively coupled plasma system. The etch rate and the selectivity were obtained with various gas mixing ratios. The maximum etch rate of $TiO_2$ thin film was 61.6 nm/min. The selectivity of $TiO_2$ to TiN, and $TiO_2$ to $SiO_2$ were obtained as 2.13 and 1.39, respectively. The etching process conditions are 400 W for RF power, -150 V for DC-bias voltage, 2 Pa for the process pressure, and $40^{\circ}C$ for substrate temperature. The chemical states of the etched surfaces were investigated with X-ray photoelectron spectroscopy (XPS). Its analysis showed that the etching mechanism was based on the physical and chemical pathways in the ion-assisted physical reaction.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.191.1-191.1
• /
• 2013

현재 산업계 전반적으로 사용되고 있는 박막형 태양전지 투명 전도막의 재료로는 ITO 와 Al, In, Ga, B, Si, F 등으로 도핑된 ZnO 박막이 사용되고 있으며, 그 중에서도 Al 이 도핑된 ZnO 박막은 넓은 밴드갭을 가진 n-type 반도체로서, 적외선 및 가시광 영역에서의 높은 투과성과 우수한 전도성을 가지며, 고온에서 안정된 전기적 특성, 낮은 원가 등의 장점을 지녀 그 응용 연구가 활발히 이루어지고 있다 [1]. 본 연구에서는 RF magnetron Sputter 법을 이용하여 Flexible 기판 위에 AZO 박막을 증착하였다. 실험변수로는 RF power, Pressure등을 이용하였고, 최적조건에서의 박막의 투과도는 90%이상, 면저항은 30 ${\Omega}/{\square}$ 이하를 나타내었다. 그리고 (주)인포비온에서 원천기술을 갖고있는 EBA technology를 이용하여 후처리 하여 전기적, 광학적, 구조적인 특성의 변화를 관찰하였다. AZO 박막의 두께를 측정하기 위해 ${\alpha}-step$과 SEM을 이용하였고, 투과도는 UV-Vis spectrometer를 사용하여 박막의 투과도 변화를 관찰 하였다. 전기적인 특성은 4-Point probe를 이용하여 측정하였다. 또한, 박막의 결정성과 거칠기의 변화는 XRD(X-ray Diffraction)와 원자간력현미경(Atomic Force Microscope; AFM) 을 이용하여 측정하였으며, 전기 광학적 특성 변화는 Figure Of Merit(FOM) 수치로 분석하였다. 본 연구에서 AZO 박막의 특성은 EBA 조사 후 특성의 향상이 이루어지는 것을 관찰할 수 있었다.