• Journal of the Korean Ceramic Society
• /
• v.27 no.2
• /
• pp.187-194
• /
• 1990

Effects of MnO2 addition ranged from 0.0wt% to 5.0wt% on the microstructure and dielectric and piezoelectric properties of the Pb(Zr0.52 Ti0.48)O3 Ceramics have been investigated. The solubility limit of MnO2 in Pb(Zr0.52 Ti0.48)O3 is about 0.5wt%, and MnO2 as a valence state of Mn3+ is substituted for (Zr, Ti) lattice site in PZT solid-solution. The addition of MnO2 up to 0.5wt% in Pb(Zr0.52 Ti0.48)O3 brings increase of density, but decreased of grain size and tetragonality. Dielectric constant slightly decreases, but both coupling factor(Kp) and mechanical quality factor(Qm) increase with the addition of MnO2. However, excess amount of MnO2 addition more than 0.75wt% results in rapid decrease of resistance. Dielectric constant and tan $\delta$ increase due to the second phase and inhomogeneous Mn distribution.

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.640-646
• /
• 1998

Nucleation and crystallzation of a quaternary glass system for lead titanate glass-ceramics were in-vestigated using DTA(differential thermal analysis ) with variation of nucleation temperature and crystal growth time. Glass samples containing 60mol% of PbO-{{{{ { TiO}_{2 } }} were prepared from melts by the conventional normal cooling method in a cylindrical brass mould. The glass sample was nucleated between 40$0^{\circ}C$ and 50$0^{\circ}C$ for a given time and showed the maximum nucleation rate at 46$0^{\circ}C$ The DTA crystallization peak temperature decreased with increasing nucleating time and decreasing heating rate during DTA runs which indicated an increase of the number of nuclei produced in the system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.608-613
• /
• 2017

We proposed a pyrometallurgical process to achieve gold alloy with an Au content of more than 80wt% from low grade (<35wt%) gold alloys. We performed the heat treatment at a temperature of $1200^{\circ}C$ for 5 hrs using Au35wt%-Ag5wt%-Cu60wt% gold alloys mixed with 1/2 weighed PbO and CaO flux by varying the ratio of PbO/(PbO+CaO) from 0 to 1. We investigated the change in content of the samples with energy dispersive X-ray spectroscopy (EDS) and time of flight secondary ion mass spectrometry (ToF-SIMS). The EDS results showed that the Au content increased from 35.0wt% in the PbO-only sample to 86.7wt% (in the PbO/(PbO+CaO) 1:1 sample), while the other samples achieved more that 84wt%. In addition, the 2/3 flux ratio sample showed the lowest Ag loss into the flux. In the ToF-SIMS results, the PbO only and CaO only fluxes had Au+ peak intensities of 349 and 37, respectively. Although the CaO-only flux might be more favorable considering the loss of Au into the flux, we concluded that the amount of Au lost into the flux could be ignored. Our results imply that that the pyrometallurgical process using a mixed flux is an effective hydrometallurgical process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.05a
• /
• pp.82-83
• /
• 1988

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.10
• /
• pp.873-877
• /
• 2007

In order to apply a complex multilayer chip LC filter, this study has estimated the interfacial reaction and coupling properties of dielectric materials $Pb(Fe_{1/2}Nb_{1/2})O_3$ and Ni-Zn-Cu ferrite materials through low-temperature co-sintering (LTCS). PFN powders were fabricated using double calcinated at $700^{\circ}C$ and then $850^{\circ}C$. While the perovskite phase rate was found to be 91 %, after heat treatment at $900^{\circ}C$ for 6h, the perovskite phase rate and density exhibited a value of 100 % and 7.46$g/cm^3$, respectively. The PFN/Ni-Zn-Cu ferrite, PFN/CUO (or $Pb_2Fe_2O_5$) and ferrite/CuO (or $Pb_2Fe_2O_5$) were mechanically coupled through interfacial reactions after the specimen was co-sintered at $900^{\circ}C$ for 6 h. No intermediate layer exists for the mutual coupling reaction. This result indicates the possibility of low-temperature co-sintering without any interfacial reaction layer for a multilayer chip LC filter.

• Journal of the Korean Ceramic Society
• /
• v.34 no.5
• /
• pp.461-466
• /
• 1997

Dielectric and piezoelectric properties of (Pb1-1.5xLnx)(Ti0.98Mn0.02)O3 ceramics with x=0~0.2 have been investigated. Pb(Ti0.98Mn0.02)O3 showed poor sinterability and cracking on cooling, but the substitution of Nd3+ ions into Pb2+ sites resulted in dense microstructures without cracking through reducing crystallographic anisotropy. The Nd3+ substitution, however, deteriorated the temperature stability of the piezoelectric properties because of lowering the Curie point. Electromechanical anisotropy(Kt/Kp) indicated a maximum value of 10 when x=0.1. This result might be attributed to the counteracting effects that with increasing x, the lattice anisotropy decreases while the poling becomes easier due to the increase in O2- vacancy concentration. Thickness-shear mode resonators with (Pb0.85Nd0.1)(Ti0.98Mn0.02)O3 composition showed good resonant characteristics around 4.5 MHz.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.2
• /
• pp.463-466
• /
• 2011

In this work, we investigate anodization of Pb in ethylene glycol containing small amount of $NH_4F$, demonstrating that ${\beta}-PbF_2$ particles with octahedral morphology can be prepared by adjusting the applied potential and anodizing time. FE-SEM images and XRD measurements of anodic nanostructures as a function of anodizing time clearly show that PbO is first formed on Pb. Subsequently, a local dissolution of PbO leads to formation of skeleton structure of PbO, releasing $Pb^{2+}$ ions in the electrolyte. The lead ions can be precipitated on the walls or intersection of the skeleton walls when the concentration of lead ions is saturated. The method described in this article shows the feasibility of formation of metal fluoride crystal by anodization of metal in a fluoride containing solution.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.5
• /
• pp.417-421
• /
• 2006

In this study, in order to develop low temperature sintering piezoelectric ceramics for LTCC (Low-Temperature Cofired Ceramic) multilayer piezoelectric actuator, PMW-PMN-PZT ceramics using $0.2wt%\; Li_2CO_3$ and $0.25wt%\;CaCO_3$ as sintering aids were investigated according to the varation of PMW substution. Composition ceramics could be sintered at $900^{\circ}C$ by adding sintering aids. As the amount of PMW substitution increased, the crystal structure of PMW-PMN-PZT ceramics moved from tetragonal phase to rhombohedral phase gradually, and MPB(Morphotrophic Phase Boundary) region appeared at 2 mol% PMW substitution. At the sintering temperature of $900^{\circ}C$, the density, electromechanical coupling factor(kp), mechanical quality factor(Qm), dielectric constant(${\epsilon}r$), piezoelectric constant(d33) and Curie temperature(Tc) of 2 mol% PMW substituted PMW-PMN-PZT ceramics showed the optimal values of $7.88g/cm^3$, 0.58, 1002, 1264, 352 pC/N and $336^{\circ}C$, respectively, for LTCC multilayer piezoelectric actuator application.

• Journal of the Korean Ceramic Society
• /
• v.29 no.1
• /
• pp.60-64
• /
• 1992

In the ceramics of PFN-PFW system modified with MnO2 dielectric properties and the relation of its microstructure have been investigated. The amount of MnO2 variations was 0, 0.05, 0.1, 0.15, 0.2, 0.25 and 0.3 mol%, respectively. In the result of the microstructure and electrical properties, the solid solution range of MnO2 was 0.15 mol%.

• Korean Journal of Crystallography
• /
• v.8 no.2
• /
• pp.97-104
• /
• 1997

Hydrothermal synthesis of PbZ1-xTixO3 has been investigated. Syntheses were performed using lead acetate triphdrate as Pb source, Ti/Zr gel by hydrolizing Ti-isopropoxide as Tiand Zr source and Zr-propoxide and KOH (0.5m, 1m, 2m) as mineralizer. The hydrothermal synthesis has been examined at 140℃, 150℃ and 160℃. Synthesized PZT powders showed a rectangular shape and were agglomerate. At 1m and 2m KOH concentrations PZT powders were synthesized the respective time of 8 hrs and 1hr but at 0.5m KOH concentration phase pure PZT powders were not synthesized for 5days reaction. At the conditions of low temperature and low KOH concentration unreacted Ti/Zr gel remained although synthesized powders were almost PZT. The size of PZT powders increased with KOH concentrations. PbO solid solutions were formed as intermediate phases and these were classified to PbO-10%TiO2 solid solution and PbO-3% TiO-3% TiO2 solid solution.