• Corrosion Science and Technology
• /
• v.20 no.2
• /
• pp.77-84
• /
• 2021

This study aims to optimize the DL-EPR test solution for duplex stainless steel S31083 using the Taguchi design. The test solution parameters applied to the Taguchi design are H₂SO₄, NaCl, KSCN concentration, and temperature. In the experimental design, an orthogonal array of 4 levels 4 factor L₁₆(4⁴) was used. Output values for the orthogonal array were used for resolution (degree of sensitization) and selective etch (I_a) values. The optimal test solution conditions were selected by comparing the normalized S/N ratio for the two reaction properties. As a result, the H₂SO₄ and NaCl were identified as the main factors influencing the sensitivity measurement, but the delta statistics showed that the KSCN concentration and temperature had relatively low influence. The optimal condition was identified as 1.5 M H₂SO₄+0.03 M KSCN+1.5M NaCl at 30 ℃. The degree of sensitization presented a tendency to depend on the heat treatment temperature and time in the optimal test solution. This investigation confirmed the possibility of optimizing the experiment solution for the DL-EPR test of stainless steel using the Taguchi technique.

• Journal of Korean Society on Water Environment
• /
• v.25 no.6
• /
• pp.979-983
• /
• 2009

The mean pH of wastewater discharged from the plating process is 2, so a less amount of alkali is required to raise pH 2 to 5. In addition, if sodium sulfite is used to raise pH 5 to 9 in the secondary treatment, caustic soda or slaked lime is not necessary or only a small amount is necessary because sodium sulfite is alkali. Thus, it is considered desirable to use only $FeSO_4{\cdot}7H_2O$ in the primary treatment. At that time, the free cyanide removal rate was highest as around 99.3%, and among heavy metals, Ni showed the highest removal rate as around 92%, but zinc and chrome showed a low removal rate. In addition, the optimal amount of $FeSO_4{\cdot}7H_2O$ was 0.3g/L, at which the cyanide removal rate was highest. Besides, the free cyanide removal rate was highest when pH value was 5. Of cyanide removed in the primary treatment, the largest part was removed through the precipitation of ferric ferrocyanide: $[Fe_4(Fe(CN)_6]_3$, and the rest was precipitated and removed through the production of $Cu_2[Fe(CN)_6]$, $Ni_2[Fe(CN)_6]$, CuCN, etc. Furthermore, it appeared more effective in removing residual cyanide in wastewater to mix $Na_2SO_3$ and $Na_2S_2O_5$ at an optimal ratio and put the mixture than to put them separately, and the optimal weight ratio of $Na_2SO_3$ to $Na_2S_2O_5$ was 1:2, at which the oxidative decomposition of residual cyanide was the most active. However, further research is required on the simultaneous removal of heavy metals such as chrome and zinc.

• Journal of the Korean Ceramic Society
• /
• v.44 no.9
• /
• pp.471-476
• /
• 2007

The hydration mechanism of the $3CaO{\cdot}Al_2O_3-CaSO_4{\cdot}2H_2O$ system in the presence of alkali sulfates has been investigated. The early hydration rate of $3CaO{\cdot}Al_2O_3$ was accelerated by the addition of $Na_2SO_4$ and $K_2SO_4$. This is closely related to the formation of syngenite $(CaSO_4{\cdot}K_2SO_4{\cdot}H_2O)$, and the U-phase added $K_2SO_4$ and $Na_SO_4$ in the $3CaO{\cdot}Al_2O_3-CaSO_4{\cdot}2H_2O$ system, respectively. The formation of the rigid syngenite and U-phase structure led to rapid setting and decreases the sulfate content in the liquid phase of the hydrating cement to the extent that it cannot adequately retard the hydration of $3CaO{\cdot}Al_2O_3$. In case of the alkali sulfate not added to the $3CaO{\cdot}Al_2O_3-CaSO_4{\cdot}2H_2O$ system, the ettringite was transformed to monosulfoaluminate immediately after the consumption of gypsum. However, when the alkali sulfates were added to this system, the ettringite did not transform to monosulfoaluminate immediately even though the gypsum was completely consumed. There was a stagnation period to transform to the monosufoaluminate after the consumption of gypsum because the syngenite and U-phase remained as the sulfate source.

• Journal of environmental and Sanitary engineering
• /
• v.20 no.4 s.58
• /
• pp.9-20
• /
• 2005

The purpose of the study was characteristics of secondary pollutants of $PM_{10}$ collected in pocheon between August 2002 and June 2003. The ambient concentrations of $PM_{10}$ mass, 9 water-soluble anions and cations, and 13 bulk composition trace elements were determined from filter samples collected by $PM_{10}$ high volume air sampler(UV-15H, Graseby-Anderson Co., USA). During this period average $PM_{10}$ mass concentration was $83.8{\mu}g/m^3(49.8{\mu}g/m^3\~111.6{\mu}g/m^3)$ in Pocheon. Mechanism for transformation of secondary pollutants by soluble ion components is divided into two categories; $NaNO_3$ type by the reaction of sea salt and $HNO_3$ in the atmosphere, and nitrate salt or phosphate salt type such as $(NH_4)_2SO_4,\;NH_4NaSO_4,\;and\;(NH_4)_2SO_4(2NH_4O_3)$.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.1
• /
• pp.39-46
• /
• 2011

NO oxidation is an important prerequisite step to assist the selective catalytic reduction (SCR) at low temperatures ($<200^{\circ}C$). Therefore, we conducted the lab- and bench-scales experiments appling the sodium chlorite powder ($NaClO_2(s)$) for the oxidation of NO to $NO_2$ and the carbon-based catalyst for the reduction of $NO_x$ and $SO_2$; the lab- and bench-scales experiments were conducted in laboratory and iron-ore sintering plant, respectively. In the lab-scale experiment, known concentrations of $NO_x$ (200 ppm), $SO_2$ (75 ppm), $H_2O$ (10%) and $NH_3$ (400 ppm) in 2.6 L/min were introduced into a packed-bed reactor containing $NaClO_2(s)$, then gases produced by the reaction with $NaClO_2(s)$ were fed into the carbon-based catalyst (space velocity = $2,000hr^{-1}$) at $130^{\circ}C$. In the bench-scale experiment, flue gases of $50Nm^3/hr$ containing 120 ppm NO and 150 ppm $SO_2$ were taken out from the duct of iron-ore sintering plant, then introduced into the flow reactor; $NaClO_2(s)$ were injected into the flow reactor using a screw feeder. Gases produced by the reaction with $NaClO_2(s)$ were introduced into the carbon-based catalyst (space velocity = $1,000hr^{-1}$). Results have shown that, in both lab- and bench-scales experiments, NO was oxidized to $NO_2$ by $NaClO_2(s)$. In addition, above 90% of $NO_x$ and $SO_2$ removal were obtained at the carbon-based catalyst. These results lead us to suggest that the combination of $NaClO_2(s)$ with the carbon-based catalyst has the potential to achieve the simultaneous removal of $NO_x$ and $SO_2$ at low temperature ($<200^{\circ}C$).

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.26 no.1
• /
• pp.139-148
• /
• 2000

The osmotic pressure is a one of the most important factor affecting stabilization of multiple emulsion in a law hours after experiment. To understand and decrease osmotic pressure between Wl phase and W2 phase, a kinds of humectants were introduced in outer water phase. As a result, Betaine and Glucose had an excellent effect reducing osmotic pressure and NaCl made W/O/W emulsion more stable than MgSO4 did when introduced in inner water phase.

• Korean Journal of Food Science and Technology
• /
• v.22 no.3
• /
• pp.343-349
• /
• 1990

The solubility of protein and phytate was measured at various pH's in distilled water and at various concentrations of NaCl, $CaCl_2\;and\;Na_2SO_3$ solutions, and then optimum condition for producing low phytate protein isolate from perilla flour was investigated. The protein solubility in water showed minimum at pH 4.0 and increased at pH higher or lower than 4.0, while phytate solubility was highest at pH 5.0 and decreased at pH higher or lower than 5.0. In NaCl solution, protein solubility was lowest between pH 3.0-4.0, while phytate solubility was high between pH 2.0-5.0 and abruptly decreased above PH 6.0. In $Na_2SO_3$ solution, protein solubility was lowest between pH 2.0-3.0 and phytate solubility showed maximum values between pH $5.0{\sim}6.0$, and it's solubility was low in 3% salt concentration at all pH ranges. In $CaCl_2$ solution, protein solubility in 3% salt concentration was relatively low at all pH ranges, and phytate solubility showed highest values between pH $2.0{\sim}3.0$ and abruptly decreased (1.0%) above pH 4.0. In order to make low phytate protein isolate, defatted perilla flour protein was extracted at pH9.0 and precipitated at pH 4.0 in 3% NaCl solution. The yield of low phytate protein isolate was 61.4% of total protein. This protein was found to contain 0.02% phytate by weight.

• The Journal of Engineering Geology
• /
• v.28 no.4
• /
• pp.565-582
• /
• 2018

We investigated the hydrochemical properties of ChusanYongchulso Spring located in Buk-myeon, Ulleung Island, focusing on the formation and characteristics of aquifers in and around the Nari caldera. Abundant pumice with high permeability and numerous fractures (including faults and joints) that formed as a result of caldera subsidence are widely distributed in the subsurface, favoring the formation of aquifers. Because of the presence of porous pyroclastic rocks with a high internal surface area, the water type of the springs is characterized by $NaHCO_3$, with upper stream waters and the upper spring being characterized by $NaHCO_3$ and NaCl, respectively. Components with a high coefficient of determination with EC are $HCO_3$, Na, F, Ca, Mg, Cl, $SiO_2$, and $SO_4$. The high concentrations of Na and Cl might be attributable to the main lithologies in the area, given that alkaline volcanic rocks are distributed extensively across Ulleung Island. Eh and pH, which are considered to be important indicators of water-rock interaction, are unrelated to most components. According to the results obtained from factor analysis, the variance explained by factor 1 is 54% and by factor 2 is 25.8%. Components with a high loading on factor 1 are F, Na, EC, Cl, $HCO_3$, $SO_4$, $SiO_2$, Ca, $NO_3$, and Mg, whereas components with a high loading on factor 2 are Mg and Ca, along with K, $NO_3$, and DO with negative loadings. It is suggested that the high concentrations of Na, Cl, F, and $SO_4$ are closely related to the presence of fine-grained alkaline pyroclastic rocks with high permeability and porosity, which favorintensewater-rock interaction. However, a wide-ranging investigation that encompasses methods such as geophysical prospecting and geochemical analysis (including isotope, trace-element, and tracer techniques) will be necessary to gain a better understanding of the groundwater chemistry, aquifer distribution, and water cycling of Ulleung Island.

• Journal of Animal Science and Technology
• /
• v.56 no.1
• /
• pp.4.1-4.7
• /
• 2014

The effect of sodium and sodium salts on carcass and body organ characteristics of broilers under a four phase feeding program were investigated. A basal diet (0.08% dNa with NaCl) was formulated and one of two sources of dNa ($NaHCO_3$ and $Na_2SO_4$) were supplemented to obtain four different percentages of dNa (0.17, 0.26, 0.35, and 0.44%) for each treatment. There was a linear decrease in dressing percentage (DP) with source ${\times}$ level interaction ($p{\leq}0.001$), while there was a linear increase in breast yield and thigh yield with increasing dNa supplementation ($p{\leq}0.001$). Chicks fed 0.35% $NaHCO_3$ and 0.44% dNa $Na_2SO_4$ supplemental salts had lower abdominal fat ($p{\leq}0.04$). Chicks that received increasing levels of dNa (from 0.17 to 0.44%) showed increasing gizzard weight ($p{\leq}0.02$) and decreasing spleen weight ($p{\leq}0.02$). When both salts were supplemented at 0.26% dNa, the chicks showed their lowest bursa weight ($p{\leq}0.001$). Consequently, chicks at higher dNa showed an increase in breast and thigh meat yield, and increasing capacity of their digestive organ. The higher levels of dNa should be tested with other cations and anions to fully understand acid base homoeostasis.

• The Korean Journal of Physiology
• /
• v.20 no.2
• /
• pp.225-235
• /
• 1986

Effects of anions on p-Aminohippurate (PAH) transport across the basolateral membrane (BLM) were studied. Basolateral membrane vesicles were isolated from rabbit renal cortex by using a self-orienting Percoll-gradient centrifugation and $Mg^{2+}-precipitation$. The characteristics of the membrane vesicles was examined by marker enzyme activity, membrane orientation and transport studies. The Na-K-ATPase activity in the fraction containing BLM vesicles was enriched 9·fold, and the alkaline phosphatase activity in the fraction containing BBM vesicles was increased 9-fold, compared with those of the homogenate. The transport properties of the two membrane preparations were studied by a rapid filtration technique. The uptake of PAH by BLM was sensitive to changes in medium osmolarity and inhibited by probenecid. When the uptake of $50{\mu}M$ PAH in voltage-clamped BLM vesicles was determined in the presence of various anions in the incubation medium, cis inhibitions by $SO_4\;and\;SSO_3$ were observed in the presence of sodium gradient (out>in). Sodium-dependent PAH uptake was inhibited competitively by external $SO_4$ PAH uptake in BLM vesicles loaded with 20 mM acetate and $SO_4\;or\;200\;{\mu}M$ PAH was significantly stimulated as compared with unloaded vesicles. The extent of trans-stmulation of PAH uptake by $SO_4$. was increased with the inside concentration of $SO_4$. This trans-stimulatory effect by $SO_4$, was observed to be additive in the presence of Na gradient and completely inhibited by 2 mM probenecid and 1 mM SITS. These results demonstrate that PAH/anion exchange is present in BLM of renal cortex and in this exchange mechanism inorganic as well as organic anions are involved as substrates.