• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.2
• /
• pp.88-94
• /
• 2009

The effect of high temperature gas nitrding (HTGN) on the surface microstructure in pure Ti was investigated. Two phases of TiN and $Ti_2N$ appeared at the outmost surface, and the wide ${\alpha}$-Ti layer was formed at the next layer. On the other hand, the interior region, where the nitrogen was not permeated, exhibited ${\alpha}$'phase. The outmost surface of TiN and $Ti_2N$ showed the maximum hardness of 1000Hv, while the interior ${\alpha}$'phase was ${\sim}350$ Hv. The permeation depth of nitrogen increased with increasing the gas nitriding temperature and time. The nitrogen concentration of the surface layer seems to be over 12.7% at $1100^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1713-1715
• /
• 1996

The $NO_2$ GAS Sensitivity characteristic of CuTBP(Copper-tetra-tert-butylphthalocyanine) LB films were investigated through a study of current-voltage (I-V) characteristics with a variation of number of electrode finger pairs N ($1{\sim}25$). A concentration of 200ppm $NO_2$ gas was used. It was found that a conductance G increases monotonically as the number of interdigital electrode increases, and a Sensitivity, Reproducibility is stable. As far as a current is concerned, the current when N=25 is greater than that when N=1 by 70 or so. It indicates that the number of interdigital electrodes affects the current, sensitivity and stability. We knew that the $NO_2$ gas detector application possibility using a current of N=25.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.471-474
• /
• 2000

A flat type microgas sensor was fabricated on the p-type silicon wafer with low stress S $i_3$ $N_4$, whose thickness is 2${\mu}{\textrm}{m}$ using MEMS technology and its characteristics were investigated. W $O_3$thin film as a sensing material for detection of N $O_2$gas was deposited using a tungsten target by sputtering method, followed by thermal oxidation at several temperatures (40$0^{\circ}C$~$600^{\circ}C$) for one hour. N $O_2$gas sensitivities were investigated for the W $O_3$thin films with different annealing temperatures. The highest sensitivity when operating at 20$0^{\circ}C$ was obtained for the samples annealed at $600^{\circ}C$. As the results of XRD analysis, the annealed samples had polycrystalline phase mixed with triclinic and orthorhombic structures. The sample exhibit higher sensitivity when the system has less triclinic structure. The sensitivities, $R_{gas}$ $R_{air}$ operating at 20$0^{\circ}C$ to 5 ppm N $O_2$of the sample annealed at $600^{\circ}C$ were approximately 90. 90.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.5
• /
• pp.96-100
• /
• 2009

With the improvement of industrial society, the high quality electrical energy, simplification of operation and maintenance, ensuring reliability and safety are being required. This paper compares breakdown characteristics in $SF_6$ gas with $N_2/O_2$ Mixture gas($N_2:O_2=100$ : 0, 79 : 21, 60 : 40, 40 : 60) as using widely in High Voltage insulation equipment with the characteristics in different media which are focused on environmentally friendly gases. As an append result of research the results are fundamental data for electric insulation design of Distribution Power Facilities which will be studied and developed in the future. And we could make an environment friendly gas insulation material with mataining dielectric strength by $N_2/O_2$ Mixture gas which generates a lower lever of the global warming effect.

• Journal of the Korean Ceramic Society
• /
• v.37 no.1
• /
• pp.1-5
• /
• 2000

Cathodoluminescence(CL) properties of ZnO:Zn green phosphor were investigated. ZnO:Zn phosphor was synthesized by varying reducing agents and firing temperatures. ZnS, charcoal and 5% H2 gas mixed with 95% N2 gas(5H2-95N2) were used as the reducing agent and atmosphere. The highest CL intensity of ZnO:Zn phosphor was observed under the condition of 5H2-95N2 atmosphere and firing temperature of 90$0^{\circ}C$ for 1h. Charocal and ZnO as reducing agents in the syntehsis of ZnO:Zn phosphor exhibited about 60% and 40%, respectively, of the CL intensity obtained with 5H2-95N2 atmosphere.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.1
• /
• pp.32-43
• /
• 1995

Ti-6Al-4V alloy are widely used in chemical and aircraft industries for their good corrosion resistance and high strength to weight ratio. Surface alloying of Ti alloy by $CO_2$ laser is able to produce few hundred micrometers thick TiN surface-alloyed layer with high hardness on the substrate very simplely by injecting reaction gas($N_2$) into a laser-generated melt pool and adjust the hardness to the specific requirements of the individual application by changing of laser processing parameters. This research has been investigated the effect of such parameters on TiN surface-alloying of Ti-6Al-4V alloy by $CO_2$ laser. The maximum hardness of TiN surface-alloyed zone waw obtained by injecting 100% $N_2$ gas and it was decreased as the amount of $N_2$ gas in Ar and $N_2$ gas mixture was decreased. As scanning speed was increased, the hardness and depth of TiN surface-alloyed zone was decreased at constant laser power. The surface hardness after double scanning laser treatment is higher than that of single scanning. At constant laser power, the surface roughness is increased after the surface alloying if laser scanning speed is decreased.

• Membrane Journal
• /
• v.23 no.6
• /
• pp.450-459
• /
• 2013

2,3,5,6-Tetramethyl-1,4-phenylenediamine (TMPD) based polyimide (PI) were crosslinked with 1,2-Diaminoethane (DAE) and 1,6-Diaminohexane (DAH) to enhance gas transport properties. Fourier transform infrared (FT-IR) studies show that imide groups were converted into amide groups during crosslinking process. Thermogravimetric analysis (TGA) results indicate that the degradation temperature of crosslinked PI membranes decreased after crosslinking. This is due to degradation of alkyl group in crosslinking agent. The d-space of crosslinked PI membranes decreased with increasing crosslinking time. The ideal permeability for $CH_4$, $N_2$, $O_2$, and $CO_2$ decreased after crosslinking and the ideal permeability of crosslinked PI membranes induced by DAH is larger than that by DAE. In contrast, the permselectivity of $CO_2/CH_4$, $CO_2/N_2$ and $O_2/N_2$ increased during crosslinking. For the gas pair of $CO_2/CH_4$, the maximum increment is about 39.5% after 6 minutes of DAE crosslinking. Also, that of $O_2/N_2$ gas pair is about 20.5% after 6 minutes of DAE crosslinking. According to these result, DAE is more suitable for enhanced permselectivity than DAH. On the contrary, DAE is not useful for $CO_2/N_2$ separation due to reduction in $CO_2/N_2$ permselectivity after 3 minutes DAE crosslinking.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.2
• /
• pp.22-25
• /
• 2020

Deep red EuSi₂O₂N₂ phosphors were synthesized under various sintering gas pressures (1 atm, 2 atm, and 3 atm). They were in good agreement with the standard EuSi₂O₂N₂ ICSD card # 41-6046 (a monoclinic crystal system with space group of P2₁/a). Their photoluminescence intensities were significantly increased with increasing the gas pressures. They showed a broad band emission peaking at 680 nm due to 4f⁶5d¹ - 4f⁷ of Eu²⁺ ion, which can be efficiently excited in the visible range up to 550 nm. The best one at 3 atm was applied for red LED based on blue chip, which showed the strong deep red emission.

• Journal of the Korean Institute of Gas
• /
• v.19 no.2
• /
• pp.37-44
• /
• 2015

We proposed the improved Langmuir adsorption relations considering volume change effect of coal matrix during primary production of CBM and Enhanced-CBM with injection of carbon dioxide or CCS in coalseam but also volumetric strain. To verify this model, experimental data of pure gas adsorption such as $CO_2$, $CH_4$, and $N_2$ on coals were used to compare conventional Langmuir model with this model. From the results, we obtained that the larger adsorption capacity of coal and the higher adsorption affinity of gas, the larger error occur with Langmuir model. Using this model, however, we found not only substantially better fit in all condition but also reasonable volumetric strain of the coal matrix. We also applied this volume modified pure gas adsorption model to the IAS model to describe gas adsorption and volumetric strain for mixed gas. This modified-IAS model fitting experimental data by Hall et al(1994) improved accuracy of mixed gas adsorption calculation compared with conventional model.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.9
• /
• pp.816-820
• /
• 2007

We measured the electron drift velocity, W, in 0.5% $SF_6-Ar$ mixture over the E/N range from 30 Td to 300 Td and gas pressure range from 0.1 to 0.5 Torr by the double shutter drift tube with a variable drift distance, and calculated over the same E/N and gas pressure range by using the two-term approximation of the Boltzmann equation. The measured and calculated values at different gas pressure at each E/N was appreciable dependence in the results on the gas pressure.