• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.305-306
• /
• 2006

Ga-doped and Al-doped ZnO thin films were fabricated via a sol-gel technique and electrical and optical properties of the films were investigated. Film deposition was performed by spin coating at 4000 rpm for 30 s on $SiO_2$ glass substrate FE-SEM was used to obtain the surface morphology images and the film thickness Four-point probe and UV-VIS spectrophotometer were used to measure the sheet resistance and the optical transparency, respectively.

• Tribology and Lubricants
• /
• v.18 no.1
• /
• pp.42-48
• /
• 2002

Experiments were conducted to determine the structural dynamic characteristics of bump foil bearing. The housing of the bearing on the journal was driven by two shakers which were used to simulate dynamic forces acting on the bump foil strips. Three different bump foils(Cu-coated bump, silicon bump, viscoelastic bump) are tested and the dynamic coefficients of three bump foils compared, based on the experimental measurements for a wide range of operating conditions. From the test results, the high damping coefficients of viscoelastic bump are achieved and the possibility of the super-bending-critical operation is suggested.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.6 s.171
• /
• pp.159-167
• /
• 2005

This work focuses on the effects of crack free friction on Mode II stress intensity factors, $K_{II}$, for a vertical surface crack in a two-dimensional finite element model of TiN/steel subject to rolling contact. Results indicate that maximum $K_{II}$ values, which occur when the load is adjacent to the crack, may be significantly reduced in the presence of crack face friction. The reduction is more significant for thick coatings than for thin. Crack extension and increased layer thickness result in increased $K_{II}$ values. The effect of crack face friction on compressive $K_I$ values appears negligible. Comparative results are presented for $MoS_2/steel$ and diamond-like carbon(DLC)/Ti systems.

• Journal of Biomedical Engineering Research
• /
• v.25 no.2
• /
• pp.157-163
• /
• 2004

Nitrogen ion implantation and ion plating techniques were applied for improvement of the wear resistance of metallic implant materials. In this work, the wear dissolution behaviour of a nitrogen ion implanted super stainless steel (S.S.S, 22Cr-20Ni-6Mo-0.25N) was compared with those of S.S.S, 316L SS and TiN coated 316L SS. The amounts of Cr and Ni ions worn-out from the specimens were Investigated using an electrothermal atomic absorption spectrometry. Furthermore, the Ti(Grade 2) disks were coated with TiN, ZrN and TiCN by use of low temperature arc vapor deposition and the wear resistance of the coating layers was compared with that of titanium. The chemical compositions of the nitrogen ion implanted and nitride coated layers were examined with a scanting auger electron spectroscopy. It wat observed that the metal ions released from the nitrogen ion implanted S.S.S surface were significantly reduced. From the results obtained, it was shown that the nitrogen ion implanted zone obtained with 100 KeV ion energy was easily removed within 200,000 revolutions from a wear dissolution testing under a similar load condition when applied to artificial hip joint. The remarkable improvement in wear resistance weir confirmed by the nitrides coated Ti materials and the wear properties differ greatly according to the chemical composition of the coating layers. for specimens with the same coating thickness of about 3$\mu\textrm{m}$, TiCN coated Ti showed the highest wear resistance. However, after removing the coating layers, the wear rates of all nitrides coated Ti reverted to their normal rates of below 10,000 revolutions from Ti-disk-on-disk wear testing under the same load condition. From the results obtained, it is suggested that the insufficient depth of the 100 Kel N$\^$＋/ ion implanted zone and of the nitrides coated layers of 3$\mu\textrm{m}$ are subject to restriction when used as frictional parts of load bearing implants.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.346-349
• /
• 2007

치밀한 $CuInSe_{2}$ (CIS) 태양전지용 광흡수층을 제조하기 위해 상용되는 출발물질을 이용하여 비진공방식인 paste coating 법으로 CIS 막을 제조하였다. 먼저 치밀한 CIS 막 제조를 위해 $Cu_{2}Se$의 액상 거동을 관찰하였다. 이러한 $Cu_{2}Se_{2}$의 액상거동을 위해 Se 분위기에서 Se 증발온도, 기판온도, 열처리시간 등을 다양하게 변화 시켰으며, Se 증발온도 $450^{\circ}C$, 기판온도 $550^{\circ}C$, 열처리시간 30분 그리고 수송가스 ($N_{2}$)를 20 sccm으로 최적조건을 형성하였다. 이러한 최적조건을 바탕으로 치밀한 CIS막을 위해 two-zone RIP (rapid temperature process) 방법으로 Se 분위기 안에서 셀렌화를 위한 열처리를 행하였다. 셀렌화를 위해 다양한 열처리시간에 따라 형성된 CIS 막은 CIS 광흡수층과 Mo 박막 사이에서 $MoSe_{2}$ 층이 형성되었지만, 균일한 CIS 막을 얻었으며 업자성장과 치밀화 거동을 관찰 하였다. 또한, CIS 막의 치밀화를 위해 Se 증발온도와 열처리시간을 고정하고 기판온도를 $600^{\circ}C$로 증가시켜 $Cu_{2}Se$의 액상거동을 관찰하였다. $600^{\circ}C$에서 형성된 CIS 막은 기판온도 $500^{\circ}C$의 시편보다 입자성장과 치밀화가 되었으나 기판으로 사용하는 soda-lime glass의 휨 현상이 발생하였다.

• Membrane Journal
• /
• v.19 no.4
• /
• pp.261-267
• /
• 2009

Polyimide which is the glassy polymer has high chemical resistance, thermal stability and high mechanical property. In this study, the polyimide hollow fiber membranes were prepared by the dry-jet wet phase inversion in order to investigate the permeation porperties of the $H_2S$ and $CH_4$. The morphology of prepared hollow fiber membranes and their permeation behaviors of $H_2S$ and $CH_4$ before and after silicon coating were evaluated. The permeance of $H_2S$ and $H_2S/CH_4$ selectivity increased due to plasticization with increasing the feed pressure. The permeance of KSM03b and selectivity of KSM03d were highest among the three type membranes used this experiments. The permeance decreased but the $H_2S/CH_4$ selectivity increased with increasing the air gap. The permeance reduced after silicon coating. However, the selectivity increased and the selectivity of KSM03d was 275 at 7 atm.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.382-382
• /
• 2009

염료감응형 태양전지의 구성체 중 전극으로 연구 되어 지고 있는 $TiO_2$는 기존에 대량 생산이 가능한 spin coating법, screen printing법, spray법의 연구가 이루어져 왔으나 고 효율 태양전지에 쓰이는 전극 시스템에 비해 고 분산성을 지닌 $TiO_2$페이스트를 제조 하는데 어려움이 있다. 그리고 플렉시블 디스플레이 소자의 응용을 위해서는 소자 공정 온도인 $250^{\circ}C$ 이하의 공정 온도가 요구 되어 지므로 고온공정인 CVD법은 이에 적합하지 않다. 이에 본 연구는 진공 증착 방법인 광원자층증착법을 이용하여 $150^{\circ}C$이하의 저온공정온도에서도 적용이 가능한 $TiO_2$ 박막을 185nm의 UV light를 조사하여 glass 기판위에 제조 하고 그에 따른 박막의 물성 분석을 하였다. Mo source로는 titanium tetraisopropoxide(TTIP)와 reactant gas 로는 $H_2O$를 사용하였으며 불활성 기체인 Ar 가스는 purge 가스로 각각 사용하였다. $100^{\circ}C{\sim}250^{\circ}C$ 공정온도를 변수로 $TiO_2$ 박막을 제조 하였으며 제조된 $TiO_2$ 박막의 물성 분석을 위해 FESEM, TEM을 이용하여 표면 및 두께를 분석하였다. 또한 $100^{\circ}C$ 400 cycles에서 약 12nm 막 두께를 관찰 할 수 있었으며 그 결과 박막의 성장률이 $0.3{\AA}$/cycle 임을 확인 할 수 있었다. 그리고 UV-VIS을 이용하여 박막의 좌외선에 대한 흡수도 및 투과도 분석을 하였다. 또한 XPS 성분 분석을 통하여 $100^{\circ}C$의 저온 공정에서 형성된 박막이 $TiO_2$임을 확인 하였다. 이러한 결과에서 185nm의 UV light에 의한 광원자층 증착법으로 $100^{\circ}C$의 저온에서도 $TiO_2$ 박막이 증착 되는 것을 확인 할 수 있었다.

• Proceedings of the KAIS Fall Conference
• /
• 2000.10a
• /
• pp.30-33
• /
• 2000

최근 국내에서도 관 동맥 질환 환자의 수가 급증하고 있으며, 관 동맥 질환의 치료 방법인 관 동맥 성형 술은 관 동맥 stent의 도입에 의하여 보편화되어 국내에서 년간 5000개 이상의 stent가 시술되고 있다. 그러나 stent는 고가(1,200천원/개)로 전량 수입에 의존하고 있으며, 시술 후 사망까지 이를 수 있는 혈전에 의한 급성 페쇠와 재 협착이 문제점이다. 이를 위한 한가지 방법이 생체 적합성이 뛰어난 복합 stent의 개발인데 SiC나 Carbon을 coating한 stent는 시술 후 혈전 형성을 억제하는 것으로 알려져 있다. 특히 가장 순수한 Pyrolytic carbon은 hemocompatibility가 탁월하고 기밀 성이기 때문에 본 연구에서 그의 CVB-Kinetics를 연구코저 하는 것이다. methane으로부터 pyrolytic carbon의 CVD는 온도에 따라서 다양한 구조를 가지며 따라서 그의 mechanism도 다양하다는 것은 잘 알려져 있다. 더구나 광간(균질)반응과 표면(불균질)반응의 정량적 관계에 따라서도 다르다는 것도 확인되었다. 그러나 stainless steel 316L로 만든 stent는 12 - 15 %의 Ni과 2%의 Mo을 함유해서 금속성을 잃지 않는 저온(600℃)에서도 pyrolytic carbon의 속매적 CVD가 가능함을 그리고 SiC의 코팅에 적합한 buffer layer 역할을 함을 확인하였다. 그리하여 본 연구는 반응기 설계에 필요한 저온 촉매적 pyrolytic carbon의 CVD-kinetics의 연구결로 그의 mechanism과 함께 rate law 식을 유도, 확인하였으며 600℃, 90kPa에서 P/sub ch4//P/sub H2/=5:1과 체류시간 1.8 sec가 최적임을 발견하였다. 이때 석출속도 11.2 g-mol/g-cat.h 혹은 두께속도로 73 nm/sec를 나타내었다.메타놀-물 (1 : 1) 유출액에서 $(0.80\;{\mu}g)$ 검출되었다. 하면 morey eel내장에서 얻은 독물질도 DEAE-셀루로즈에서 ST-1 과 ST-2로 나누어지며, 이 ST-1의 TLC, HPLC 및 알루미나 컬럼상의 거동이 파랑비늘돔에서 얻은 ST-1의 그것과 같으므로 scaritoxin으로 보고한 ST-1은 ciguatoxin의 형태인 less polar cigutoxin (LPCTX) 으로 생각된다.에서 각각 대조구의 57, 413 및 315% 증진되었다. 거품의 열안정성은 15분 whipping시, pH 4.0(대조구, 30.2%) 및 5.0(대조구, 23.7%)에서 각각 $0{\sim}38.0$ 및 $0{\sim}57.0%$이었고 pH 7.0(대조구, 39.6%) 및 8.0(대조구, 43.6%)에서 각각 $0{\sim}59.4$ 및 $36.6{\sim}58.4%$이었으며 sodium alginate 첨가시가 가장 양호하였다. 전체적으로 보아 거품안정성이 높은 것은 열안정성도 높은 경향이며, 표면장력이 낮으면 거품형성능이 높아지고, 비점도가 높으면 거품안정성 및 열안정성이 높아지는 경향이 있었다.protocol.eractions between application agents that are developed using different languages. Dynamic agent invocation is accomplished by Java Native Interface(JNI) that links two heterogeneous methods, and by KQML language interface that facilitates the communications between heterogeneous agents. This scheme of dyna

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.388-388
• /
• 2016

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated with cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature $T_s$, and substrate dc bias $V_s$ as variables for efficient PEDOT:PSS/crystalline (c-)Si heterojunction solar cells (Fig. 1). The high-speed camera and differential mobility analysis characterizations revealed that average size and flux of PEDOT:PSS mist depend on f, solvent, and $V_s$. The size distribution of mist particles including EG/DI water cosolvent is also shown at three different $V_s$ of 0, 1.5, and 5 kV for a f of 3 MHz (Fig. 2). The size distribution of EG/DI water mist without PEDOT:PSS is also shown at the bottom. A peak maximum shifted from 300-350 to 20-30 nm with a narrow band width of ~150 nm for PEDOT:PSS solution, whose maximum number density increased significantly up to 8000/cc with increasing $V_s$. On the other hand, for EG/water cosolvent mist alone, the peak maximum was observed at a 72.3 nm with a number density of ~700/cc and a band width of ~160 nm and it decreased markedly with increasing $V_s$. These findings were not observed for PEDOT:PSS/EG/DI water mist. In addition, the Mie scattering image of PEDOT:PSS mist under white bias light was not observed at $V_s$ above 5 kV, because the average size of mist became smaller. These results imply that most of solvent is solvated in PEDOT:PSS molecule and/or solvent is vaporized. Thus, higher f and $V_s$ generate preferentially fine mist particle with a narrower band width. Film deposition occurred when $V_s$ was impressed on positive to a c-Si substrate at a Ts of $30-40^{\circ}C$, whereas no deposition of films occurred on negative, implying that negatively charged mist mainly provide the film deposition. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrate by adjusting $T_s$ and $V_s$. The adhesion of CMD PEDOT:PSS to c-Si enhanced by $V_s$ conspicuously compared to that of spin-coated film. The CMD PEDOT:PSS/c-Si solar cell devices on textured c-Si(100) exhibited a ${\eta}$ of 11.0% with the better uniformity of the solar cell parameters. Furthermore, ${\eta}$ increased to 12.5% with a $J_{sc}$ of $35.6mA/cm^2$, a $V_{oc}$ of 0.53 V, and a FF of 0.67 with an antireflection (AR) coating layer of 20-nm-thick CMD molybdenum oxide $MoO_x$ (n= 2.1) using negatively charged mist of 0.1 wt% 12 Molybdo (VI) phosphoric acid n-Hydrate) $H_3(PMo_{12}O_40){\cdot}nH_2O$ in methanol. CMD. These findings suggest that the CMD with negatively charged mist has a great potential for the uniform deposition of organic and inorganic on textured c-Si substrate by adjusting $T_s$ and $V_s$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.34 no.2
• /
• pp.266-276
• /
• 1996

Numerous factors are known to affect the accuracy of elastomeric impression materials. Factor often overlooked is the quality of the bond between putty and wash during corrective reline impression technique. The putty-wash bond strength must be strong enough to over-come the local stress at putty-wash interface. It is not always possible to avoid saliva contamination in making corrective wash impres-sion. And putty preliminary impression material con be used as a template for provisional restoration. Human saliva and the residual monomer of autopolymerizing acrylic resin are thought to affect the bond strength and the failure type. This study examined the effect of contaminants like human saliva, and residual resin monomer on the putty-wash bond strength and the effectiveness of treatment. 1. Of the tested three brands of Vinyl Polysiloxane impession meterial, Express Exhibited the greatest bond strength followed by Eamix and Perfect showed the lowest putty-wah bond strength. 2. Coating the putty substrates with human saliva did not produce decreased failure load in all the breands of Vinyl Polysiloxane impression meterail. 3. Of the three brands of VPS impression material that were exposed to methhylmethacry-late resin(Jet), only the putty-wash bond strength of the Perfect group diminished signifi-cantly. Moreover, all the specimens from group C of Perfect exhibited adhesive failure. 4. Exposing the substrates to ethylmethacrylate resin(SNAP. diminished the putty-wash bond strength significantly. With Perfect and Examix, failure occurred cohesively through the light-body, whereas with Express, failure occurred adhesive-cohesively. 5. Removing approximately 1mm thickness of the contaminated putty interface was the most effective treatment in countering the undesirable effect caused by residual resin monomer. The putty-wash bond strength of the groups that were treated with 1mm even putty reduction was not significantly different from those of control groups. With Perfect and Examix, cleaning the specimens with gauze soaked in 70% isopropyl alcohol increased the putty-wash bond strength, but was not as effective as 1mm even reduction of contaminated putty substrates. With Express, 70% isoproryl alcohol treatment exhibi0ted comparable putty-wash bond strength to that of control group.