• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.85-89
• /
• 2022

We reported on annealing effect on Ga₂O₃/Al₂O₃/SiC devices grown by radio frequency sputtering method. Post-deposition annealing at 900 ℃ was performed, which results in crystallization in the Ga₂O₃ films. The major peaks (-401) and (403) of Ga₂O₃ which was thermally treated at 900 ℃ appears in the x-ray diffraction (XRD) results. Auger electron spectroscopy (AES) shows that Ga and Al atoms seems to be diffused into the opposite direction Al₂O₃ and Ga₂O₃ after annealing. Transfer and output characteristics of back-gate transistor were analyzed where SiC substrate is used as gate material. On-state current and on/off ratio increased almost 10⁹ and 10⁶ times higher in the 900 ℃ annealed sample.

• Journal of the Korean Ceramic Society
• /
• v.48 no.6
• /
• pp.604-609
• /
• 2011

Additives for low temperature sintering of mullite ceramics were investigated for matching Mo-Cu conducting paste with that ceramics at 1,400$^{\circ}C$. $SiO_2$, MgO and $Y_2O_3$ were chosen as the additives for low temperature sintering, and the amounts of those additives were varied with sintering temperature of 1,400$^{\circ}C$ to 1,500$^{\circ}C$. With additives of 1.0 wt% of $SiO_2$, 1.0 wt% of MgO, and 1.5 wt% of $Y_2O_3$, the densest sintered body of 3.12 g/$cm^3$ was obtained at 1,400$^{\circ}C$ in reducing atmosphere. The flexural strength of that was 325 MPa and the CTE (Coefficient of thermal expansion) was 4.33 ppm/$^{\circ}C$.

• The Korean Journal of Ceramics
• /
• v.5 no.2
• /
• pp.115-118
• /
• 1999

Carbon composites with $MoSi_2$ dispersion were prepared by hot-pressing at $1700^{\circ}C$ under 30 MPa for 1 h using polysilazance as binding material. The composites consisted of C, $Mo_{4.8}Si_3C_{0.6}$ and SiC. Bulk density and porosity of the carbon composites with 10 vol% $MoSi_2$ was 1.8g.$\textrm{cm}^{-3}$ and 34%, respectively. This composite was oxidized about 0.05mm from the surface of the carbon composite after oxidation test at $1500^{\circ}C$ for 10h in air. Formation of the $SiO_2$ glass layer was observed by SEM. When this composite suffered damage in the coating layer, it had hardly farther oxidation because of its self-repairing property. The composite prepared in this study indicated good oxidation resistance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.1
• /
• pp.86-92
• /
• 2022

Despite otherwise advantageous properties, the performance and reliability of devices manufactured in β-Ga₂O₃ on semi-insulating Ga₂O₃ substrates may degrade because of poorly mitigated self-heating, which results from the low thermal conductivity of Ga₂O₃ substrates. In this work, we investigate and compare self-heating and device performance of β-Ga₂O₃ MESFETs on substrates of semi-insulating Ga₂O₃ and 4H-SiC. Electron mobility in β-Ga₂O₃ is negatively affected by increasing lattice temperature, which consequently also negatively influences device conductance. The superior thermal conductivity of 4H-SiC substrates resulted in reduced β-Ga₂O₃ lattice temperatures and, thus, mitigates MESFET drain current degradation. This, in turn, allows practically reduced device dimensions without deteriorating the performance and improved device reliability.

• Analytical Science and Technology
• /
• v.14 no.4
• /
• pp.317-323
• /
• 2001

Dissolution procedures of Monsanto catalyst which has been used to produce acrylronitrile by ammoxidation of propylene have been studied. Optimum dissolution condition of the catalyst supported on silica was obtained by microwave digestion system with mixed of HCl, HF and $H_2O_2$. When a safety device was activated by increased pressure in microwave vessel, Bi, Fe, Mo, Sb and U were not volatilized even though silica was volatilized as $SiF_4$. Quantification results by this method were $SiO_2$ $50.5{\pm}0.4%$, $Sb_2O_3$ $29.6{\pm}0.6%$, $UO_2$ $10.2{\pm}0.1%$, $Fe_2O_3$ $6.1{\pm}0.1%$, $MoO_3$ $0.73{\pm}0.01%$ and $Bi_2O_3$ $0.49{\pm}0.01%$ by ICP-AES and the relative error was within ${\pm}10%$ except bismuth.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.2-2
• /
• 2011

Single-walled carbon nanotubes (SWNTs) have been considered as a promising candidate for nextgeneration electronics due to its extraordinary electrical properties associated with one-dimensional structure. Since diversity in electronic structure depends on geometrical features, the major concern has been focused on obtaining the diameter, chirality, and density controlled SWNTs. Despite huge efforts, the controlled synthesis of SWNTs has not been achieved. There have been various approaches to synthesize controlled SWNTs by preparation of homogeneously sized catalyst because the SWNTs diameter highly depends on catalyst nanoparticles size. In this study, geometrically controlled SWNTs were synthesized using designed catalytic layers: (a) morphologically modified Al2O3 supporting layer (Fe/Al2O3/Si), (b) Mo capping layer (Mo/Fe/Al/Si), and (c) heat-driven diffusion and subsequent evaporation process of Fe catalytic nanoparticles (Al2O3/Fe/Al2O3/Si). These results clearly revealed that (a) the grain diameter and RMS roughness of Al2O3 supporting layer play a key role as a diffusion barrier for obtaining Fe nanoparticles with a uniform and small size, (b) a density and diameter of SWNTs can be simultaneously controlled by adjusting a thickness of Mo capping layer on Fe catalytic layer, and (c) SWNTs diameter was successfully controlled within a few A scale even with its fine distribution. This precise control results in bandgap manipulation of the semiconducting SWNTs, determined by direct comparison of Raman spectra and theory of extended tight binding Kataura plot. We suggest that these results provide a simple and possible way for the direct growth of diameter, density, and bandgap controlled SWNTs by precise controlling the formation of catalytic films, which will be in demand for future electronic applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.341-345
• /
• 2001

In this study, nano-sized powders of SiO$_2$-0∼15mo1%B$_2$O$_3$ composition were prepared by sol-gel processing method using TEOS(Tetra ethyl ortho silicate) and H$_3$BO$_3$ solution. The powders were tape-cast on High silicate glass sheet(HSG) substrate and sintered to form a layer of undercladding for the planar light wave module. During the sol-gel processing, H$_2$O/Si mole ratio were varied to modify the size of the powders in a range from 600 to 75nm. The dispersion of the powder was modified by changing the pH of the slurry. Sintering temperature of the tape was observed to decrease with the size of the powder and the B$_2$O$_3$ content in the powder. When the silica powders of 75∼125nm in diameter containing 15mo1% B$_2$O$_3$ were used, 98 TD% was obtained at 1250$^{\circ}C$, which is approximately 300$^{\circ}C$ reduction in sintering temperature compared with micrometer-sized powders.

• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.671-676
• /
• 2014

It is known that bones get damaged by accidents and aging. Since the discovery of Bioglass, various kinds of ceramics have been also found to bond to living bone; some of these ceramics are already being clinically used as bone-repairing materials. In the present study, antibacterial calcium silicate gel ($Ag-30CaO{\cdot}70SiO_2$ gel) was prepared by sol-gel method in order to control the microstructure, which is related to the dissolution rate and induction period of apatite formation in body environment. In addition, biological $Ag-30CaO{\cdot}70SiO_2$ is tested. This was done to impart antimicrobial activity to the $30CaO{\cdot}70SiO_2$. Ag ion was added during sol-gel synthesis to replace the $H_2O$ added during the making of the $30CaO{\cdot}70SiO_2$ gel, which has silver solutions of various concentration. After the sol-gel process, 1N-$HNO_3$ solution was used to wash the gel when synthesizing the gel, in order to maintain the porous structure and remove PEG, water soluble polymers. Then, the apatite forming ability of the sol-gel derived CaO-$SiO_2$ gels was investigated using simulated body fluid (SBF), which had almost the same ion concentration as that of human blood plasma. The gels were analyzed by FT-IR spectroscopy, SEM observation, XRD, and fluorescent microscopy. The apatite was successfully created even after washing the gel; apatite is present in an amorphous state, and was found to affect the concentration of the Ag ion in cells in MC3T3 live & dead assay results. From these results, it is suggested that a good material that can be used to repair defects of nature bone is $Ag-30CaO{\cdot}70SiO_2$ gel.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.5
• /
• pp.386-391
• /
• 2017

Two kinds of steels whose compositions were Fe-34.4Cr-14.5Ni-2.5Mo-0.4W-0.4Mn-0.5Si-(0.009 or 0.35)S (wt.%) were centrifugally cast, and oxidized at $900^{\circ}C$ for 50-350 h in order to find the effect of sulfur on the high-temperature oxidation of Fe-34.4Cr-14.5Ni-2.5Mo-0.4W-0.4Mn-0.5Si-(0.009 or 0.35)S (wt.%) alloys. These alloys formed oxide scales that consisted primarily of $Cr_2O_3$ as the major oxide and $Cr_2MnO_4$ as the minor one through preferential oxidation of Cr and Mn. They additionally formed $SiO_2$ particles around the scale/alloy interface as well as inside the matrices. The high affinity of Mn with S led to the formation of scattered MnS inclusions particularly in the 0.35S-containing cast alloy. Sulfur was harmful to the oxidation resistance, because it deteriorated the scale/alloy adherence so as to accerelate the adherence and compactness of the formed scales.

• Journal of the Mineralogical Society of Korea
• /
• v.32 no.3
• /
• pp.223-234
• /
• 2019

The geology of the Samdeok Mo deposit consists of Paleozoic Hwajeonri formation, Kowoonri formation, Suchangri formation, Iwonri formation, Hwanggangri formation, Cretaceous, leucocratic porphyritic granite and granitic porphyry. This deposit consists of three quartz veins that filled NS oriented fractured zones in Suchangri formation. Quartz veins vary from 0.05 m to 0.3 m in thickness and extend to about 400 m in strike length. Quartz veins occur as massive, breccia, and cavity textures. Wallrock alteration has silicification, sericitization, argillitization and chloritization. The mineralogy of the quartz veins consists of quartz, fluorite, white mica, biotite, apatite, monazite, rutile, ilmenite, molybdenite, chalcopyrite, Fe-Mg-Mn oxide and Fe oxide. White mica from Samdeok Mo deposit occurs as fine or coarse grains in quartz vein and hostrock and has four mineral assemblages (I type: quartz, molybdenite, Fe oxide and Fe-Mg-Mn oxide, II type: quartz, Fe oxide and Fe-Mg-Mn oxide, III type: quartz and biotite, and IV type: quartz). The structural formular of white mica from quartz vein is $(K_{0.89-0.60}Na_{0.05-0.00}Ca_{0.01-0.00}Sr_{0.02-0.00})_{0.94-0.62}(Al_{1.54-1.12}Mg_{0.36-0.18}Fe_{0.26-0.09}Mn_{0.04-0.00}Ti_{0.02-0.00}Cr_{0.02-0.00}Zn_{0.01-0.00})_{1.91-1.72}(Si_{3.40-3.11}Al_{0.92-0.60})_{4.00}O_{10}(OH_{1.68-1.42}F_{0.58-0.32})_{2.00}$, but white mica of I type has higher FeO content, and lower $SiO_2$ and MgO contents than white micas of other types. Also, compositional variations in white mica from the Samdeok Mo deposit are caused by phengitic or Tschermark substitution ($(Al^{3+})^{VI}+(Al^{3+})^{IV}{\leftrightarrow}(Fe^{2+}{\text{ or }}Mg^{2+})^{VI}+(Si^{4+})^{IV}$) and direct $(Fe^{3+})^{VI}{\leftrightarrow}(Al^{3+})^{VI}$ substitution.