• 한국광물학회지
• /
• 제3권2호
• /
• pp.72-78
• /
• 1990

Polycrystalline MaF2(rutile structure) has been studied up to∼15 GPa under truly hydrostatic pressures in a diamond anvil cell(DAC) at room temperature. Its bulk modulus was determined to 96.0 GPa, from two independent runs using Birch-Murnaghan equation of state with an assumed Ko' of 5.1 from ultrasonic measurements. These are in good agreement with the previously reported values by both ultrasonic and X-ray diffraction meth-ods.

• 대한화학회지
• /
• 제43권1호
• /
• pp.52-57
• /
• 1999

In($C_6F_5)_3{\cdot}D(D=CH_3CN$, O($C_2H_5)_2$)와 ($CH_3)_3SiC_6F_5$/CsF, $C_6F_5$MgBr 또는 Cd($C_6F_5)_2$을 반응시켜 [In($C_6F_5)_4$]- 음이온 화합물을 합성하였으나, 이들 indium(III) 음이온 화합물들은 온도에 민감하고 습기에 대해 불안정하다. 안정한 indium(III) 음이온 착물은 PNPCl(PNP=bis(triphenylphosphino)ammonium)과의 양이온 치환반응시켜 얻었으며, 관 크로마토 그래피를 이용하여 분리 정제하였다. 합성된 화합물의 특성은 핵자기 공명 분석법, 적외선 분광분석법, 분자량 측정, DTA/TG 그리고 원소분석법을 이용하여 조사하였다.

• 한국재료학회지
• /
• 제28권8호
• /
• pp.435-439
• /
• 2018

MA Al alloys are examined to determine the effects of alloying of Mg and Cu and rolling on tensile deformation behavior at 748 K over a wide strain rate range($10^{-4}-10^3/s$). A powder metallurgy aluminum alloy produced from mechanically alloyed pure Al powder exhibits only a small elongation-to-failure(${\varepsilon}_f$ < ~50%) in high temperature(748 K) tensile deformation at high strain rates(${\acute{\varepsilon}}=1-10^2/s$). ${\varepsilon}_f$ in MA Al-0.5~4.0Mg alloys increases slightly with Mg content(${\varepsilon}_f={\sim}140%$ at 4 mass%). Combined addition of Mg and Cu(MA Al-1.5%Mg-4.0%Cu) is very effective for the occurrence of superplasticity(${\varepsilon}_f$ > 500%). Warm-rolling(at 393-492 K) tends to raise ${\varepsilon}_f$. Lowering the rolling-temperature is effective for increasing the ductility. The effect is rather weak in MA pure Al and MA Al-Mg alloys, but much larger in the MA Al-1.5%Mg-4.0%Cu alloy. Additions of Mg and Cu and warm-rolling of the alloy cause a remarkable reduction in the logarithm of the peak flow stress at low strain rates (${\acute{\varepsilon}}$< ~1/s) and sharpening of microstructure and smoothening of grain boundaries. Additions of Mg and Cu make the strain rate sensitivity(the m value) larger at high strain rates, and the warm-rolling may make the grain boundary sliding easier with less cavitation. Grain boundary facets are observed on the fracture surface when ${\varepsilon}_f$ is large, indicating the operation of grain boundary sliding to a large extent during superplastic deformation.

• 한국수소및신에너지학회논문집
• /
• 제33권2호
• /
• pp.148-157
• /
• 2022

Research on hydrogen storage is active to properly deal with hydrogen, which is considered a next-generation energy medium. In particular, research on metal hydride with excellent safety and energy efficiency has attracted attention, and among them, magnesium-based hydrogen storage alloys have been studied for a long time due to their high storage density, low cost, and abundance. However, Mg-based alloys require high temperature conditions due to strong binding enthalpy, and have many difficulties due to slow hydrogenation kinetics and reduction in hydrogen storage capacity due to oxidation, and various strategies have been proposed for this. This research manufactured Mg₂Ni to improve hydrogenation kinetics and synthesize about 5, 10, 20 wt% of CaF₂ as a catalyst for controlling oxidation. Mg₂NiHx-CaF₂ produced by hydrogen induced mechanical alloying analyzed hydrogenation kinetics through an automatic PCT measurement system under conditions of 423 K, 523 K, and 623 K. In addition, material life cycle assessment was conducted through Gabi software and CML 2001 and Eco-Indicator 99' methodology, and the environmental impact characteristics of the manufacturing process of the composites were analyzed. In conclusion, it was found that the effects of resource depletion (ARD) and fossil fuels had a higher burden than other impact categories.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.561-565
• /
• 2002

The effects of sintering additives such as $Bi_2O_3$ and $V_2O_5$ on the microwave dielectric and sintering properties of (Zn, Mg)$TiO_3$ system were investigated. Highly dense samples were obtained for $(Zn_{0.8}Mg_{0.2})TiO_3$ at the sintering temperature range of $870{\sim}900^{\circ}C$ with $Bi_2O_3$ and $V_2O_5$ additions of <1wt.%, respectively. The microwave dielectric properties of $(Zn_{0.8}Mg_{0.2})TiO_3$ with 0.45 wt.% $Bi_2O_3$ and 0.55 wt.% $V_2O_5$ sintered at $900^{\circ}C$ were as follows: $Q{\times}f_o$=56,800 GHz, ${\varepsilon}_r$=22, and ${\tau}_f=-53ppm/^{\circ}C$. In order to improve temperature coefficient of resonant frequency, $TiO_2$ was added to the above system. The optimum amount of $TiO_2$ was 15 mol.% when sintered at $870^{\circ}C$, at which we could obtain following results: $Q{\times}f_o$ = 32,800 GHz, ${\varepsilon}_r$ = 26, and $\tau_f=0ppm/^{\circ}C$.

• 멤브레인
• /
• 제21권2호
• /
• pp.201-211
• /
• 2011

본 연구에서는 정수처리용 세라믹 한외여과 빛 광촉매의 혼성공정에서 휴믹산 농도 및 광산화, 흡착의 영향을 알아보았다. 휴믹산 농도 각각 2mg/L와 4 mg/L 일 때 UF 단독 공정 및 광촉매를 투입한 공정, UV를 조사한 공정을 막오염에 의한 저항$(R_f)$ 및 투과선속(J), 총여과부피 $(V_{\Upsilon})$ 측면에서 고찰하였다. 휴믹산 농도가 낮아질수록 $R_f$는 급격히 감소하고 J는 증가하여, 휴믹산 농도 2 mg/L에서 $V_{\Upsilon}$는 가장 높았다. 탁도의 평균 처리효율은 휴믹산 농도가 증가할수록 감소하였으나, 4 mg/L에서 휴믹산의 처리효율이 가장 높았다. 이러한 결과는 낮은 휴믹산 농도에서 휴믹산 대부분이 분리막에 의해 제거되고 막을 통과한 일부 휴믹산은 광촉매에 흡착 산화되어, 처리수의 수질이 휴믹산 2 mg/L 와 4 mg/L 에서 거의 같고 원수의 수질은 4 mg/L에서 더 높기 때문이다. 광산화와 흡착의 영향 실험에서 UF + $TiO_2$ + UV 공정의 J가 가장 높게 유지되어, 180분 운전 후 $V_{\Upsilon}$가 가장 높았다. 휴믹산 및 탁도의 처리효율을 비교한 결과, 휴믹산 농도가 2 mg/L 에서 4mg/L로 증가하였을 때 광산화 보다 광촉매 흡착이 더 주요한 역할을 하였다.

• BMB Reports
• /
• 제37권2호
• /
• pp.199-205
• /
• 2004

The six lumbrokinase fractions (F1 to F6) with fibrinolytic activities were purified from earthworm Lumbricus rubellus lysates using the procedures of autolysis, ammonium sulfate fractionation, and column chromatography. The proteolytic activities on the casein substrate of the six iso-enzymes ranged from 11.3 to 167.5 unit/mg with the rank activity orders of F2 > F1 > F5 > F6 > F3 > F4. The fibrinolytic activities of the six fractions on the fibrin plates ranged from 20.8 to 207.2 unit/mg with rank orders of F6 > F2 > F5 > F3 > F1 > F4. The molecular weights of each iso-enzyme, as estimated by SDS-PAGE, were 24.6 (F1), 26.8 (F2), 28.2 (F3), 25.4 (F4), 33.1 (F5), and 33.0 kDa (F6), respectively. The plasminogen was activated into plasmin by the enzymes. The optimal temperature of the six iso-enzymes was $50^{\circ}C$, and the optimal pH ranged from pH 4-12. The four iso-enzymes (F1-F4) were completely inhibited by PMSF. The two enzymes (F5 and F6) were completely inhibited by aprotinin, TLCK, TPCK, SBTI, LBTI, and leupeptin. The N-terminal amino acid (aa) sequences of the first 20 to 22 residues of each fraction had high homology. All six isoenzymes had identical aa residues 2-3 and 13-15. The N-terminal 21-22 aa sequences of the F2, F3, and F4 isoenzymes were almost the same. The N-terminal aa sequences of F5 and F6 were identical.

• 한국가축번식학회지
• /
• 제15권2호
• /
• pp.109-115
• /
• 1991

This experiment was conducted to find out the time to farrowing induction after PGF2$\alpha$ treatment, the rate of farrowing induction, the effect of kids born by the induced farrowing on birth weight and development with study on artificial control of parturition in Korean native goats. A total of 24 pluriparous goats were offered for this experiment. The animals were divided into 4 goats per treatment by administration time(142, 145 or 148 day of pregnancy) and dosage (5 or 7.5mg). The results obtained in this experiments were as follows : 1. The effect of synchronization of estrus was induced 23 goats(95.1%), 16 goats(66.6%) in the 1st treatment and 7 goats(28.5%) in the 2nd treatment PGF2$\alpha$ and exhibited estrus at a mean interval of 75$\pm$5 hours after PGF2$\alpha$ injection. 2. The time to farrowing induction after PGF2$\alpha$ treatment on day 145 or 148 was significantly(P<0.01) shorter than that of the 5mg treatment, but there was no significant difference(P>0.01). 3. Parturition was induced in all goats(100%) treated 5 or 7.5mg of PGF2$\alpha$ on day 148 and 7.5mg of PGF2$\alpha$ on day 145, but was induced 75% in treatment with 5mg of PGF2$\alpha$ on day 145 and 5 or 7.5mg of F2$\alpha$ on day 142. 4. The birth weight and development of kids induced farrowing was heaviest (P<0.01) on days 148 among treatment, but there was no significant difference in dosage.

• 식물병연구
• /
• 제26권4호
• /
• pp.250-255
• /
• 2020

페룰산 함량이 붉은곰팡이병과 곰팡이독소 저항성 곡류 육종의 선발지표가 될 수 있는지 알기 위해 밀, 보리, 벼 육성 품종 80점의 페룰산 함량을 조사하였다. 페룰산 함량은 보리 20품종이 1.66-2.77 mg/g, 밀 40품종이 0.56-1.53 mg/g이었으며 벼 20품종은 0.91-2.13 mg/g이었다. 이 중 페룰산 함량이 다른 밀과 보리 각 7품종을 선정하여 F. graminearum과 F. asiaticum 각 2균주의 붉은곰팡이병과 독소 생성량을 분석하였다. 밀 품종의 평균 병원성은 페룰산 함량이 높은 보리에 비해 유의하게 낮았고 밀 품종 간에는 상관관계가 없었다. 곰팡이독소도 병원성과 같이 페룰산 함량이 낮은 밀이 보리보다 생성량이 낮았다. 그러나 보리에서는 F. asiaticum 균주의 병원성과 독소 생성량이 페룰산 함량과 음의 상관관계를 나타내었다. 이 결과는 페룰산 함량이 밀과 보리에서 F. graminearum과 F. asiaticum에 의한 붉은곰팡이병과 독소 생성에 저항성 요인이 아님을 보여준다.

• Journal of Information Display
• /
• 제7권2호
• /
• pp.1-5
• /
• 2006

The characteristics of MgO layer deposited under hydrogen atmosphere were investigated. Hydrogen gas was introduced during e-beam evaporation coating process of MgO layer and its effects on microstructure, cathode luminescence spectra, discharge voltages and effective yield of secondary electron emission were examined. The results indicated that the hydrogen influences the concentration and energy levels of defects in MgO layer, which in turn affects the luminance efficiency and discharge delays of the panels significantly.