• Resources Recycling
• /
• v.30 no.6
• /
• pp.43-52
• /
• 2021

In this study, the optimal nitration process for selective lithium leaching from powder of a spent battery cell (LiNi_xCo_yMn_zO₂, LiCoO₂) was studied using Taguchi method. The nitration process is a method of selective lithium leaching that involves converting non-lithium nitric compounds into oxides via nitric acid leaching and roasting. The influence of pretreatment temperature, nitric acid concentration, amount of nitric acid, and roasting temperature were evaluated. The signal-to-noise ratio and analysis of variance of the results were determined using L₁₆(4⁴) orthogonal arrays. The findings indicated that the roasting temperature followed by the nitric acid concentration, pretreatment temperature, and amount of nitric acid used had the greatest impact on the lithium leaching ratio. Following detailed experiments, the optimal conditions were found to be 10 h of pretreatment at 700℃ with 2 ml/g of 10 M nitric acid leaching followed by 10 h of roasting at 275℃. Under these conditions, the overall recovery of lithium exceeded 80%. X-ray diffraction (XRD) analysis of the leaching residue in deionized water after roasting of lithium nitrate and other nitrate compounds was performed. This was done to determine the cause of rapid decrease in lithium leaching rate above a roasting temperature of 400℃. The results confirmed that lithium manganese oxide was formed from lithium nitrate and manganese nitrate at these temperatures, and that it did not leach in deionized water. XRD analysis was also used to confirm the recovery of pure LiNO₃ from the solution that was leached during the nitration process. This was carried out by evaporating and concentrating the leached solution through solid-liquid separation.

• Economic and Environmental Geology
• /
• v.42 no.3
• /
• pp.247-259
• /
• 2009

This study is focused on the relationship between whole rock boron contents and metamorphic P-T conditions of metasedimentary rocks from northeastern Yeongnam massif around Samcheok area, Korea. Metamorphic P-T conditions of sillimanite and garnet zones based on the Ti-biotite geothermometer is 553-687$^{\circ}C$ and 582-722$^{\circ}C$ at 4-6 kbar, respectively. In the metasedimentary rocks, boron contents in whole rock decrease with increasing metamorphic grade, from sillimanite zone (9.60-189 ppm B) to garnet zone (2.63-15.97 ppm B), except one sample (90.9 ppm B) from garnet zone containing graphites. Boron depletion in garnet zone has relation with mode of tourmaline which are broken down with increasing metamorphic temperature. Boron contents are indirectly proportional to major and trace elements such as $Al_2O_3$, MgO, $Fe_2O_3$, $K_2O$, Li, Ba, Sc, Co, Cr, Rb and Cs that are abundant in tourmalines. In conclustion, tourmalines and graphite are modulator of boron contents in metasedimentary rocks. In the biotite granitic gneisses, boron contents (2.62-12.2 ppm B) are similar or lower than those of metasedimentary rocks and have no relation with metamorphic P-T conditions.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.133.2-133.2
• /
• 2010

현재 융융탄산염 연료전지의 공기극으로 다공성의 lithiated NiO를 사용하고 있는데 이 재료의 경우 크게 두 가지의 문제점을 안고 있다. 첫 번째는 Ni이 전해질 내로 용해하는 것이고, 두 번째는 낮은 활성으로 인한 높은 공기극의 분극이다. Ni이 전해질로 용해되는 문제는 Co나 Fe를 코팅하여 공기극 표면에 $Li_x(Ni_yCo_{1-y})1-xO_2$나 $Li_x(Ni_yFe_{1-y})_{1-x}O_2$를 형성시켜 NiO의 전해질 내로 용해되는 것을 억제하는 방법이나 ZnO, MgO, $La_2O_3$ 등의 산화물을 NiO 표면에 코팅하여 전해질과 접촉을 막는 방식으로 해결하는 등 많은 연구가 이루어져 왔다. 하지만 연료극의 비해 상당히 높은 공기극의 분극으로 인해 큰 전압손실이 일어나 용융탄산염 연료전지 성능이 낮아지는 문제의 경우 이를 해결하고자 하는 연구는 상대적으로 많이 진행되지 못한 상태이다. 특히 현재 용융탄산염 연료전지의 장기수명화를 위해 기존의 작동온도인 $650^{\circ}C$ 보다 다소 낮은 온도인 $600{\sim}620^{\circ}C$에서 작동하려는 움직임이 있다. 작동 온도가 내려가면 전해질이 휘발되는 속도가 낮아져 전해질 부족에 따른 운전시간이 줄어드는 문제를 해결할 수 있어 장기 수명화를 위해서는 작동온도를 낮추는 것이 매우 유리하다. 하지만 작동 온도가 내려가면서 양 전극에서 일어나는 전기화학 반응 속도가 느려지기 때문에 각 전극에서의 활성화 분극으로 인한 전압손실은 더욱 커질 수밖에 없다. 특히 연료극의 수소산화반응 속도는 공기극의 산소환원반응에 비해 매우 빠르기 때문에 작동 온도가 내려감에 따라 연료극의 분극이 커지는 것에 비해 공기극의 분극이 급격히 커지게 된다. 따라서 운전온도가 낮아지는 상황에서는 낮은 작동온도에서도 성능감소가 적게 일어나 0.8V 이상 운전(150mA/$cm^2$, 단위전지 기준)이 가능한 공기극의 개발이 매우 필요한 실정이다. 이를 해결하고자 본 연구에서는 고체 산화물 연료전지의 공기극의 재료로 많이 연구되고 있는 혼합전도성 물질의 페로브스카이트 구조의 물질을 기존 NiO 전극에 코팅하여 새로운 공기극을 개발하였다. 페로브스카이트 구조의 물질로 대표적인 LSCF 물질을 사용하였으며 LSCF를 코팅한 공기극을 이용한 단위전지에서 150mA/$cm^2$의 전류를 흘려주었을 때 0.84V의 성능을 1000hr 유지하였다. 이는 기존의 NiO 전극을 사용했을 때보다 15~20mV 높은 값이다. 낮은 작동온도에서도 좋은 성능을 보였는데, 기존의 NiO 전극의 경우 $630^{\circ}C$에서 0.79V의 성능을 보인 반면 LSCF가 코팅된 공기극의 경우 $620^{\circ}C$에서 0.811V의 매우 좋은 성능을 보였다. 이는 LSCF의 산소이온전도성 및 전기전도성이 공기극에서의 분극을 낮추어 성능을 증가시키는 것으로 보인다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.344-345
• /
• 2006

In this study, in order to develop low temperature sintering piezoelectric transformer, $(Pb_{0.99-x}Ca_xSr_{0.01})Ti_{0.96}(Mn_{1/3}Sb_{2/3})_{0.04}O_3$ ceramic systems were fabricated using $Na_2CO_3-Li_2CO_3$ as sintering aids and investigated with the amount of Ca substitution. The piezoelectric transformer requires high electromechanical coupling factor $k_t$ and high mechanical quality factor $Q_{mt}$ for generating high output power At the ($PbCaSr)Ti(MnSb)O_3$ ceramics with 24mol% Ca substitution sintered at $900^{\circ}C$, electromechanical coupling factor $k_t$ and mechanical quality factor $Q_{mt}$ showed the optimal values of 0.504 and 1655 respectively, for thickness vibration mode multilayer piezoelectric transformer application.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.1
• /
• pp.1-12
• /
• 2012

In this study, $CO_2$ adsorbent was developed for removing low concentration of $CO_2$ in multiple-use facilities. The efficiency of the adsorbent which was improved selective $CO_2$ adsorption capabilities was evaluated. The pellet type adsorbent was modified from a commercial zeolite with mixing LiOH, binder, additives, and $H_2O$. Column tests showed over 90 % of $CO_2$ was adsorbed within 400min. Chamber tests including batch and continuous types were performed for evaluating the adsorbent module. By batch tests, it was evaluated that about 92% of $CO_2$ was removed within 30 min. By continuous tests, 70% of $CO_2$ was removed within 30 min. It was analyzed that over 2,500 ppm of $CO_2$ was continuously removed as shown chamber tests. The reproducibility tests repeatedly performed for 15 days shows that over 1,000 ppm of $CO_2$ was continuously removed. Adsorption capacity of the developed adsorbent was 5.0mmol $CO_2/g$ adsorbent which was analyzed by TGA. It was estimated that the modified adsorbent was applicable to low $CO_2$ concentration and low temperature of indoor environment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.5
• /
• pp.417-421
• /
• 2006

In this study, in order to develop low temperature sintering piezoelectric ceramics for LTCC (Low-Temperature Cofired Ceramic) multilayer piezoelectric actuator, PMW-PMN-PZT ceramics using $0.2wt%\; Li_2CO_3$ and $0.25wt%\;CaCO_3$ as sintering aids were investigated according to the varation of PMW substution. Composition ceramics could be sintered at $900^{\circ}C$ by adding sintering aids. As the amount of PMW substitution increased, the crystal structure of PMW-PMN-PZT ceramics moved from tetragonal phase to rhombohedral phase gradually, and MPB(Morphotrophic Phase Boundary) region appeared at 2 mol% PMW substitution. At the sintering temperature of $900^{\circ}C$, the density, electromechanical coupling factor(kp), mechanical quality factor(Qm), dielectric constant(${\epsilon}r$), piezoelectric constant(d33) and Curie temperature(Tc) of 2 mol% PMW substituted PMW-PMN-PZT ceramics showed the optimal values of $7.88g/cm^3$, 0.58, 1002, 1264, 352 pC/N and $336^{\circ}C$, respectively, for LTCC multilayer piezoelectric actuator application.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.1
• /
• pp.35-39
• /
• 2006

In this study, in order to develop the multilayer piezoelectric actuator and ultrasonic resonator, PMN-PNN-PZT ceramics were fabricated by sintering with $Li_2CO_3-Na_2CO_3$ as sintering aids at $950^{\circ}C$ and their piezoelectric and dielectric characteristics were investigated as a function of PNN substitution. With increasing PNN substitution, dielectric constant(${\epsilon}_r$), electromechanical coupling factor(kp), and piezoelectric d constant($d_{33}$) were increased to $12 mol\%$ PNN substitution and then showed a tendency to decrease rapidly With increasing PNN substitution, crystal structure changed from tetragonal to rhombohedral at $12 mol\%$ PNN substitution and then secondary phase was appeared and its intensity was increased. At the $12 mol\%$ PNN substituted PMN-PZT composition ceramic sintered at $950^{\circ}C$, density, kp, $d_{33}$ and Qm showed the optimum value of $7.79 g/cm^3$, 0.599, 419 pC/N, and 894, respectively for multilayer piezoelectric actuator application.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.9
• /
• pp.756-760
• /
• 2007

Flame retardant(FR) properties were investigated with tricredyl phosphate(TCP) and tris(pentafluorophenyl)phosphine(TFPP) as additives for lithium-ion batteries. Thermal stability was improved with additives in $Li/LiNi\frac{1}{3}Mn\frac{1}{3}Co\frac{1}{3}O_2$ cells comparing to non-additive electrolytes. Oxygen evolution reaction of the cathode material was delayed to up $55^{\circ}C$, from $275^{\circ}C\;to\;330^{\circ}C$. Electrolytes with the 1 wt.% additives provided good FR properties while the resonable battery performance is maintained.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.8
• /
• pp.1299-1304
• /
• 2007

New sulfur functionalized cyclopentadiene ligands, 1-[2-(thioanisole)]-2,5-dimethylcyclopentadiene (3), 1-[2- (thioanisole)]-2,3,5-trimethylcyclopentadiene (4), and 1-[2-(thioanisole)]-2,3,4,5-tetramethylcyclopentadiene (5), were prepared. In these ligands, the S-donor atom is connected to a cyclopentadiene ring by a rigid phenylene spacer. CpCo(III)-diiodo half-sandwich complexes (6-8) were obtained from reaction the ligands (3- 5) with Co2(CO)8, followed by treatment of I2. Substitution reaction of CpCo(III)-diiodo complexes with MeLi yielded the corresponding CpCo(III)-dimethyl complexes (9-11). Further transformation to the corresponding cationic cobalt complexes (12-14) were achieved by reaction of the CpCo(III)-dimethyl complexes with HB(ArF)4·2Et2O and trapping with CD3CN. The new sulfur functionalized cyclopentadiene ligands having a rigid phenylene spacer and the corresponding cobalt complexes were characterized by 1H, 13C and 19F NMR spectroscopy. The diiodo Complex 6 was also characterized by a single crystal X-ray diffraction method.

• Journal of the Korean Electrochemical Society
• /
• v.20 no.2
• /
• pp.27-33
• /
• 2017

Conventional lithium ion batteries suffer from notorious safety issues caused by inevitable lithium dendrite formation and proliferation during over/fast charging processes. The lithium dendrites or mechanical damage on the separator induce internal short circuit in LiB that generates extensive amount of heat within contacted electrode surfaces through the separator. During this heat generation, conventional polyolefin separators shrinks dramatically, and increasing short circuit pathway, that causes the battery to explode. To overcome this serious issue, ceramic coated separators are developed in commercial LiB to enhance thermal and mechanical stability. In this paper, various size(IL = 488.5 nm, I = 538.7 nm, S = 810.3 nm, D = 1533.3 nm) of $Al_2O_3$ particles are coated using styrene-butadiene rubber(SBR) / carboxymethyl cellulose(CMC) binder on PE separator to investigate its thermal stability and electrochemical effect on LiB coin cell with NCM cathode and Li metal anode.