• Bulletin of the Korean Chemical Society
• /
• v.29 no.9
• /
• pp.1737-1741
• /
• 2008

The electrochemical and thermal stability of $LiNi_{0.8}Co_{0.16}Al_{0.04}O_2$ were studied before and after $Co_3(PO_4)_2$ coating. Different to conventional coating material such as $ZrO_2$ or AlPO4, the coating layer was not detected clearly by TEM analysis, indicating that the $Co_3(PO_4)_2$ nanoparticles effectively reacted with surface impurities such as $Li_2CO_3$. The coated sample showed similar capacity at a low C rate condition. However, the rate capability was significantly improved by the coating effect. It is associated with a decrease of impedance after coating because impedance can act as a major barrier for overall cell performances in high C rate cycling. In the DSC profile of the charged sample, exothermic peaks were shifted to high temperatures and heat generation was reduced after coating, indicating the thermal reaction between electrode and electrolyte was sucessfully suppressed by $Co_3(PO_4)_2$ nanoparticle coating.

• Korean Journal of Materials Research
• /
• v.28 no.5
• /
• pp.273-278
• /
• 2018

Lithium-ion batteries have been considered the most important devices to power mobile or small-sized devices due to their high energy density. $LixCoO_2$ has been studied as a cathode material for the Li-ion battery. However, the limitation of its capacity impedes the development of high capacity cathode materials with Ni, Mn, etc. in them. The substitution of Mn and Ni for Co leads to the formation of solid solution phase $LiNi_xMn_yCo_{1-x-y}O_2$ (NMC, both x and y < 1), which shows better battery performance than unsubstituted $LiCoO_2$. However, despite a high discharge capacity in the Ni-rich compound (Ni > 0.8 in the metal site), poor cycle retention capability still remains to be overcome. In this study, aiming to improve the stability of the physical and chemical bonding, we investigate the stabilization effect of Ca in the Ni-rich layered compound $Li(Ni_{0.83}Co_{0.12}Mn_{0.05})O_2$, and then Ca is added to the modified secondary particles to lower the degree of cationic mixing of the final particles. For the optimization of the final grains added with Ca, the Ca content (x = 0, 2.5, 5.0, 10.0 at.%) versus Li is analyzed.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.1
• /
• pp.112-119
• /
• 2022

Molten carbonate fuel cells (MCFCs) are environmentally friendly, large-capacity power generation devices operated at approximately 650℃. If MCFCs are to be commercialized by improving their competitiveness, their cell life should be increased by operating them at lower temperatures. However, a decrease in the operating temperature causes a reduction in the cell performance because of the reduction in the electrochemical reaction rate. The cell performance can be improved by introducing a coating on the cathode of the cell. A coating with a high surface area expands the triple phase boundaries (TPBs) where the gas and electrolyte meet on the electrode surface. And the expansion of TPBs enhances the oxygen reduction reaction of the cathode. Therefore, the cell performance can be improved by increasing the reaction area, which can be achieved by coating nanosized LiCoO₂ particles on the cathode. However, although a coating improves the cell performance, a thick coating makes gas difficult to diffuse into the pore of the coating and thus reduces the cell performance. In addition, LiCoO₂-coated cathode cell exhibits stable cell performance because the coating layer maintains a uniform thickness under MCFC operating conditions. Therefore, the performance and stability of MCFCs can be improved by applying a LiCoO₂ coating with an appropriate thickness on the cathode.

• Journal of the Korean Ceramic Society
• /
• v.53 no.3
• /
• pp.306-311
• /
• 2016

Li-air batteries have received much attention due to their superior theoretical energy density. However, their sluggish kinetics on the cathode side is considered the main barrier to high performance. The rational design of electrode catalysts with high activity is therefore an important challenge. To solve this issue, we performed density functional theory (DFT) calculations to analyze the adsorption behavior of the $LiO_2$ molecule, which is considered to be a key intermediate in both the Li-oxygen reduction reaction (ORR) and the evolution reaction (OER). Specifically, to use the activity descriptor approach, the $LiO_2$ adsorption energy, which has previously been demonstrated to be a reliable descriptor of the cathode reaction in Li-air batteries, was calculated on $LaB_{1-x}B^{\prime}_xO_3$(001) (B, B' = Mn, Fe, Co, and Ni, x = 0.0, 0.5). Our fast screening results showed that $LaMnO_3$, $LaMn_{0.5}Fe_{0.5}O_3$, or $LaFeO_3$ would be good candidate catalysts. We believe that our results will provide a way to more efficiently develop new cathode materials for Li-air batteries.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.3
• /
• pp.415-420
• /
• 2020

Strontium is known as a salt-soluble element during the electrolytic oxide reduction (EOR) process. The chemical behavior of SrO during EOR was investigated via thermodynamic calculations to provide quantitative data on the chemical status of Sr. To achieve this, thermodynamic calculations were conducted using HSC chemistry software for various EOR conditions. It was revealed that SrO reacts with LiCl salt to produce SrCl₂, even in the presence of Li₂O, and that the ratio of SrCl₂ depends on the initial concentration of Li₂O dissolved in LiCl. It was found that SrO reacts with Li to produce Sr during EOR and that the reduced Sr reacts with LiCl salt to produce SrCl₂. As a result, the proportions of metallic forms were lower in Sr than in La and Nd under various EOR conditions. The thermodynamic calculations indicated that the three chemical forms of SrO, SrCl₂, and Sr co-exist in the EOR system under an equilibrium with Li, Li₂O, and LiCl.

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.249-254
• /
• 2003

AI, AIN and additives such as Li$_2$CO$_3$, Y$_2$O$_3$ and CaCO$_3$ which promoted nitridation were mixed, formed and heat-treated in nitrogen atmosphere. The effect of solvent, additive and temperature on nitridation of AI-AIN system was studied. When ethanol containing 1 wt% oleic acid was used as a mixing solvent, the formation of oxide was minimized due to surface modification of AI and AIN particles. The addition of Li$_2$CO$_3$ or CaCO$_3$ as an additive extremely diminished the formation of oxide which formed during heat treatment for nitridation compared with the addition of Y$_2$O$_3$.

• 한국전기화학회:학술대회논문집
• /
• 2005.04a
• /
• pp.52-52
• /
• 2005

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.311-312
• /
• 2006

The dielectric Properties of add $Li_2CO_3$ to ($Ba_{0.6}Sr_{0.4})TiO_3$ powder in this research, made thick film by tape casting method and annealing at $970^{\circ}C$ for 2 hours each from the $O_2$, Ar and O2-plasma atmosphere were investigated. The dielectric Properties of Ar atmosphere was to higher with tunability. The dielectric constant was increased and Curie temperature was shifted to higher temperature with increasing of annealing temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.452-452
• /
• 2009

HEV용 리튬 이차전지의 양극물질로서 $LiMn_2O_4$는 일반적으로 사용되고 있는 $LiCoO_2$에 비해 값이 저렴하고 독성이 낮으며, 높은 전압과 좋은 율 특성을 갖는 물질이다. 하지만 고온에서 전이금속인 Mn이 전해액으로 용출되어 급격한 용량감소로 인한 짧은 수명의 단점을 가지고 있다. 흔히 전구체로 쓰이는 $MnO_2$, $Mn_3O_4$, MnOOH등은 전기 분해법을 이용한 EMD가 주로 이용된다. 본 연구에서는 출발 물질로 $KMnO_4$와 $Mn(NO_3)_2$를 수용액 반응을 시켜서 농도, 온도변화에 따른 입자 형상 및 크기와 결정상의 변화를 관찰하고, 화학적 방법으로 얻어진 $MnO_2$와 LiOH를 합성하여 각각의 $LiMn_2O_4$를 비교 분석하고자한다.

• Journal of Electrochemical Science and Technology
• /
• v.15 no.1
• /
• pp.168-177
• /
• 2024

Ni-rich cathode is one of the promising candidates for high-energy lithium-ion battery applications. Due to its specific capacity, easy industrialization, and good circulation ability, Ni-rich cathode materials have been widely used for lithium-ion batteries. However, due to the limitation of the co-precipitation method, including sewage pollution, and the instability of the long production cycles, developing a new efficient and environmentally friendly synthetic approach is critical. In this study, the Ni_0.91Co_0.06Mn_0.03CO₃ precursor powder was successfully synthesized by an efficient spray-drying method using carbonate compounds as a raw material. This Ni_0.91Co_0.06Mn_0.03CO₃ precursor was calcined by mixing with LiOH·H₂O (5 wt% excess) at 480℃ for 5 hours and then sintered at two different temperatures (780℃/800℃) for 15 hours under an oxygen atmosphere to complete the cathode active material preparation, which is a key component of lithium-ion batteries. As a result, LiNi_0.91Co_0.06Mn_0.03O₂ cathode active material powders were obtained successfully via a simple sintering process on the Ni_0.91Co_0.06Mn_0.03CO₃ precursor powder. Furthermore, the obtained LiNi_0.91Co_0.06Mn_0.03O₂ cathode active material powders were characterized. Overall, the material sintered at 780℃ shows superior electrochemical performance by delivering a discharge capacity of 190.76 mAh/g at 1^st cycle (0.1 C) and excellent capacity retention of 66.80% even after 50 cycles.