• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.4
• /
• pp.421-429
• /
• 2018

Hydrazine based reductive dissolution applied on magnetite oxide was investigated. Dissolution of Fe(II) and Fe(III) from magnetite takes place either by protonation, surface complexation, or reduction. Solution containing hydrazine and sulfuric acid provides hydrogen to break bonds between Fe and oxygen by protonation and electrons for the reduction of insoluble Fe(III) to soluble Fe(II) in acidic solution of pH 3. In terms of dissolution rate, numerous transition metal ions were examined and Cu(II) ion was found to be the most effective to speed up the dissolution. During the cycle of Cu(I) ions to Cu(II) ions, the released electron promoted the reduction of Fe(III) and Cu(II) ions returned to Cu(I) ion due to the oxidation of hydrazine. In the experimental results, the addition of a very low amount of cupric ion (about 0.5 mM) to the solution increased the dissolution rate about 40% on average and up to 70% for certain specific conditions. It is confirmed that even though the coordination structure of copper ions with hydrazine is not clear, the $Cu(II)/H^+/N_2H_4$ system is acceptable regarding the dissolution performance as a decontamination reagent.

• 한국전기화학회:학술대회논문집
• /
• 1999.04a
• /
• pp.61-61
• /
• 1999

• Journal of Convergence for Information Technology
• /
• v.11 no.2
• /
• pp.117-123
• /
• 2021

The effects of electrolyte concentration on the electrochemical properties of Fe4[Fe(CN6)]3(FeHCF) as a novel active material for the electrode of aqueous zinc-ion batteries was investigated. The electrochemical reactions and structural stability of the FeHCF electrode were significantly affected by the electrolyte concentration. In the electrolyte solutions of 1.0-7.0 mol dm-3, the charge-discharge capacities increased with increasing electrolyte concentration, however gradually decreased as the cycle progressed. On the other hand, in the 9.0 mol dm-3 electrolyte solution, the initial capacity was relatively small, however showed good cyclability. Additionally, the FeHCF electrode after five cycles in the former electrolyte solutions, had a change in crystal structure, whereas there was no change in the latter electrolyte solution. This suggests that the performance of the FeHCF electrode is greatly influenced by the hydration structure of zinc ions present in electrolyte solutions.

• Journal of the Korean Magnetics Society
• /
• v.10 no.2
• /
• pp.81-85
• /
• 2000

Crystallographic and magnetic properties of the Mn-doped orthoferrite LaFe$_{1-x}$Mn$_{x}$ O$_3$(0.0$\leq$x$\leq$O.4) system have been investigated by means of x-ray diffractometry, M ssbauer spectroscopy, vibrating sample magnetometer and super-conducting quantum interference device. The structure of the system was found to be orthorhombic distorted perovskite structure. At room temperature, the M ssbauer spectra for x=0.0 consists of one Zeeman sextets from Fe$^{3+}$ ions at octahedral sites. The M ssbauer spectra of two Zeeman sextets (x$\leq$0.1) change one Zeeman sextets and a paramagnetic doublet (x=0.4). The saturation magnetization increases but the coercivity decreases with increasing x in LaFe$_{1-x}$Mn$_{x}$ O$_3$.

• The Korean Journal of Mycology
• /
• v.19 no.3
• /
• pp.220-225
• /
• 1991

Activities of the $F_1-ATPase$ purified from Lentinus edodes were stimulated by $Fe^{3+},\;Fe^{2+},\;Cd^{2+},\;Mg^{2+},\;K^{+}\;and\;Co^{2+}$ but were inhibited by $Zn^{2+},\;Ca^{2+},\;Cu^{2+}\;and\;Ni{2+}$ ion. The enzyme activities were increased 130, 65, 65, 68, 105% and 23% by the 5mM $Fe^{3+}$, 10 mM$Fe^{2+}$, 1mM $Cd^{2+}$, 5mM $Mg^{2+}$, 5mM $K^{+}$ and 5mM$Co^{2+}$ ion addition, respectively, as compared with those not added. The enzyme activities were decreased 18, 19, 27 and 30% by 10 mM $Zn^{2+}$, 10mM $Ca^{2+}$, 0.5 mM $Cu^{2+}$ and 10 mM $Ni^{2+}$ ion, respectively. Anion effects of 10 mM ${Co_3}^{2-}$, 20 mM,$CN^{-}$ 20 mM$CH_3COO^{-}$ and 20 mM ${NO_3}^{-}$ ion were inhibited to the enzyme activities of 98, 95, 70 and 50%, respectively. As increasing of ${SO_4}^{2-}$ ion concentration, the enzyme activity was stimulated and 20 mM ${SO_4}^{2-}$ ion was shown increased of 21%.

• Resources Recycling
• /
• v.7 no.3
• /
• pp.3-10
• /
• 1998

Simulated waste liquid containing 50 ppm cobalt ion was treated by adsorbing colloidal flotation using Fe(III) or Al(IlI) as flocclant and a sodium lamyl sulfate as a collector. Parameters such as pH, surfactant concentration, Fe(III) or Al(III) concentration, gas flow rate, etc., W앙e considered. The flotation with Fe(III) showed 99.8% removal efficiency of cohalt on the conditions of initial cobalt ion concentration 50 ppm, pH 9.5, gas flow rate 70 ml/min, and flotation time 30 min. When the waste solution, was treated with 35% $H_2O_2$ prior to adsorbing colloidal flotation, the optimal pH for removing cobalt shifted m to weak alkaline range and flotation could be applied in wider range of pH as compared to non-use of $H_2O_2$. Additional use of 20 ppm Al(III) after precipitation of 50 ppm Co(II) with 50 ppm Fe(III) made the optimal pH range for preferable flotation w wider. Foreign ions such as, $NO_3^-$, $SO_4^{2-}$, $Na^+$, $Ca^{2+}$ were adopted and their effects were observed. Of which sulfate ion was f found to be detrimental to removal of cob퍼t ion by flotation. Coprecipitation of Co ion with Fe(III) and Al(III) resulted in b better removal efficiency of cobalt IOn 피 the presence of sulfate ion.

• Journal of the Korean Magnetics Society
• /
• v.19 no.6
• /
• pp.216-221
• /
• 2009

Y-type barium ferrite $Ba_2Co_2Fe_{12}O_{22}$ was synthesized by a solid state reaction method. Effects of metal ion mole ratio and calcination temperatures on magnetic properties and microstructures of the synthesized powders were investigated. Phase analysis and microstructure observation were performed with a XRD (X-ray diffractometer) and a FESEM (field effect scanning electron microscope), respectively. Magnetic properties of the powders were measured with a VSM (vibrating sample magnetometer). Single phase Y-type was synthesized when metal ion mole fraction $Fe^{3+}:\;Ba^{2+}:\;Co^{2+}$ was 6 : 1 : 1 and calcination temperature was $1050\;{^{\circ}C}$. High saturation magnetization value of 39.1 emu/g was obtained when metal ion mole fraction $Fe^{3+}:\;Ba^{2+}:\;Co^{2+}$ was 8 : 1 : 1 and calcination temperature was $1200\;{^{\circ}C}$.

• 한국문화재보존과학회:학술대회논문집
• /
• 2002.02a
• /
• pp.45-52
• /
• 2002

본 연구에서는 KaOH, $K_2CO_3$, Sodium, 그리고 1차 이온수 용액의 $Cl^-$ 이온 추출량과 부식생성물의 생성순위, 부식물 생성, 그리고 부식물 제거에 관하여 관찰하였으며 이 연구로 아래와 같은 결과를 얻었다. $Cl^-$ 이온 추출량에 대한 실험 결과 NaOH은 탈염 초기에는 Cl- 이온을 잘 추출시켰으나 탈염 횟수가 증가하면서 $Cl^-$ 이온의 추출량이 급감하였다. 또한 유물 중량 변화에도 감소폭이 가장 심하였다. $K_2CO_3$은 NaOH나 1차이온수 용액과 비교해 보면 이 방법은 탈염처리동안 $Cl^-$ 이온을 꾸준히 추출시켜 주었으며 다른 탈염용액에 비해 유물 중량변화가 거의 관찰되지 않았다. Sodium 용액은 $K_2CO_3$ 용액과 마찬가지로 탈염처리 동안 $Cl^-$ 이온을 꾸준히 추출시켰으며 다른 탈염 용액에 비해 $Cl^-$ 이온 추출량이 가장 많았다. 하지만 이 용액은 약품 내에 불순물인 $Cl^-$ 이온을 $3\~5\;ppm$을 기지고 있어 보존처리자가 탈염처리를 할 때 좀 더 신중하게 생각해야 할 것 같다. 1차 이온수 용액은 부식인자가 $Cl^-$이온을 완전하게 제거해주지는 못하였지만, pH가 $7.5\~7.9$로 다른 탈염 용액에 비해서 전위차가 낮으며, 별도로 탈알칼리 처리를 하지 않아도 되기 때문에 유물손상은 극소화할 수가 있다. 따라서 이 용액은 부식이 매우 심한 철제 유물이나 균열이 많은 주조 철편과 같은 유물을 처리할 때 적절한 용액이다. 부식생성물 관찰에서는 출토 철기 유물에 생성된 부식물은 주로 인철광$(\gamma-FeOOH)$, 침철광$(\alpha-FeOOH)$, 적금광$(\beta-FeOOH)$, 그리고 자철광$(Fe_3O_4)$이다. 인위적 부식에서는 전부 인철광의 부식물이 생성되었고 자연적 부식에서는 모두 침철광의 부식물이 생성되었다. 특히 철제 표면에 자연적으로 생성된 공식 녹을 XRD 분석한 결과 적금광으로 동정되었다. 이런 모든 시편들을 각 탈염방법에 따라 탈염처리한 후 XRD와 SEM-EDS으로 분석한 결과 인철광과 침철광은 어떠한 변화도 보이지 않았고, 다만 적금광으로 동정된 시편만이 잔존하지 않았다. 철기 제작별 $Cl^-$ 이온 추출량과 탈염효과에 대한 비교 실험은 이온 크로마토그래피 분석 결과와 마찬가지로 단조 철제유물이 주조 철제보다 $Cl^-$ 이온을 많이 가지고 있었으며, 탈염 처리 후에는 $Cl^-$ 이온은 전혀 발견되지 않았다. 이상의 결과 $K_2CO_3$와 Sodium 용액은 탈염처리에서 가장 적합한 탈염처리 용액으로 알수가 있었으며 특히 어떠한 탈염 용액으로 유물을 처리한다 해도 철제유물에 생성된 부식물은 제거되지 않는다는 것을 알게 되었다. 따라서 보존처리자는 유물 표면의 부식 상태만을 보고 처리하기 보다는 철기제작물로 고려하여 처리하는 것이 필요하다. 또한 금속에 부식을 야기시키는 $Cl^-$ 이온과 부식물을 완전하게 제거하여 탈염처리를 하는 것이 유물 부식을 최대한 지연시킬 수 있는 것이라 생각된다.

• Journal of the Korean Vacuum Society
• /
• v.16 no.4
• /
• pp.262-266
• /
• 2007

Polycrystalline $Mn_xFe_{3-x}O_4$ thin films were synthesized on Si(100) substrates using sol-gel method and the effects of Mn substitution on the structural, magnetic, and magnetotransport properties were analyzed. X-ray diffraction revealed that cubic structure is maintained up to x = 1.78 with increasing lattice constant for increasing x. Such increase of the lattice constant is attributable to the substitution of $Mn^{2+}$ (with larger ionic radius) ions into tetrahedral $Fe^{3+}$(with smaller ionic radius) sites. VSM measurements revealed that $M_s$ does not vary significantly with x, qualitatively explainable by comparing spin magnetic moments of Mn and Fe ions. On the other hand, $H_c$ was found to decrease with increasing x, attributable to the decrease of magnetic anisotropy due to the decrease of $Fe^{2+}$ density through $Mn^{2+}$ substitution. Magnetoresistance (MR) of the $Mn_xFe_{3-x}O_4$ films was found to decrease with increasing x. Analysis of the MR data in comparison with the VSM results gives an indication of the tunneling of spin-polarized carriers through the grain boundaries of the polycrystalline samples at low external field and spin-flip of the carriers at high external field.

• Journal of the Korean Magnetics Society
• /
• v.17 no.1
• /
• pp.10-13
• /
• 2007

Single crystalline, $LuFe_2O_4$, was grown by the floating zone method. The crystal structure was a two-dimensional layered-type rhombohedral($R\={3}mh$) structure, with an $a_0=3.440(2)\;{\AA}\;and\;a\;c_0=25.263(2)\;{\AA}$. The magnetic $N\'{e}el$ temperature($T_N$) was determined to be 250 K. The $M\"{o}ssbauer$ spectrum at 12 K was fitted with four sextet sets which was resulted from the crystal structure. The spectrm at room temperature consisted of three singlets and a doublet with the electric quadrupole splitting. The isomer shift($\delta$) value of the singlet was $0.20{\pm}0.01mm/s$ relative to the Fe metal indicating the $Fe^{3+}$ valence state, and the value of the doublet was $0.70{\pm}0.01mm/s$ indicating $Fe^{2+}$. The $M\"{o}ssbauer$ absorption area ratio between $Fe^{3+}$ and $Fe^{2+}$ at room temperature was 1:1. The doublet phase of spectra gradually disappears by up to 360 K. At 360 K, the spectrum shows the singlet phase. We suggested that the spontaneous polarization effect of $LuFe_2O_4$ was caused by the change of iron behavior.