• 한국가시화정보학회:학술대회논문집
• /
• 2002.11a
• /
• pp.1-6
• /
• 2002

How is the flow in a rotating impeller. About 35 years have passed since one experimentalist rotating with the impeller. of a huge centrifugal blower made the flow measurements using a hot-wire anemometer (Fowler 1968). Optical measurement methods have great advantages over the intrusive methods especially for the flow measurement in a rotating impeller. One is the optical flow visualization (FV) technique (Senoo, et al., 1968) and the other is the application of laser velocimetry (LV) (Hah and Krain, 1990). Particle image velocimetries (PIVs) combine major features of both FV and LV, and are very attractive due to the feasibility of simultaneous and multi-points measurements (Hayami and Aramaki, 1999). A high-pressure-ratio transonic centrifugal compressor with a low-solidity cascade diffuser was tested in a closed loop with HFC134a gas at 18,000rpm (Hayami, 2000). Two kinds of measurement techniques by image processing were applied to visualize a flow in the compressor. One is a velocity field measurement at the inducer of the impeller using a PIV and the other is a pressure field measurement on the side wall of the cascade diffuser using a pressure sensitive paint (PSP) measurement technique. The PIV was successfully applied for visualization of an unsteady behavior of a shock wave based on the instantaneous velocity field measurement (Hayami, et al., 2002b) as well as a phase-averaged velocity vector field with a shock wave over one blade pitch (Hayami, et al., 2002a. b). A violent change in pressure was successfully visualized using a PSP measurement during a surge condition even though there are still some problems to be overcome (Hayami, et al., 2002c). Both PIV and PSP results are discussed in comparison with those of laser-2-focus (L2F) velocimetry and those of semiconductor pressure sensors. Experimental fluid dynamics (EFDs) are still growing up more and more both in hardware and in software. On the other hand, computational fluid dynamics (CFDs) are very attractive to understand the details of flow. A secondary flow on the side wall of the cascade diffuser was visualized based either steady or unsteady CFD calculations (Bonaiuti, et al.,2002). EFD and CFD methods will be combined to a hybrid method being complementary to each other. Measurement techniques by image processing as well as CFD calculations give a huge amount of data. Then, data mining technique will become more important to understand the flow mechanism both for EFD and CFD.

• Journal of Korean Philosophical Society
• /
• v.123
• /
• pp.1-26
• /
• 2012

Ist der Emotivismus eine $mi{\ss}lungene$ Theorie? Nach der Meinung von Jesse Prinz ist es nicht so. Auf der Humeschen Tradition stehend behauptet er, $da{\ss}$ ein moralisches Urteil ohne das Sentiment von Billigung oder $Mi{\ss}billigung$ nicht zustandekommen kann. Ihm zufolge ist Emotion nicht allein mit moralischen Urteilen verbunden, sondern auch eine notwendige und hinreichende Bedingung $daf{\ddot{u}}r$. Der Grund dessen, warum der Emotivisums nicht ${\ddot{u}}berzeugend$ erschien, liegt darin, $da{\ss}$ $f{\ddot{u}}r$ diesen die Verbindung von Emotion und Moral nur auf den $Gef{\ddot{u}}hlsausdruck$ $beschr{\ddot{a}}nkt$ bleibt. Zwar stellt das moralische Urteil Sentiment dar, aber das bleibt eben nicht als ein $blo{\ss}$ $Gef{\ddot{u}}hlsausdruckendes$. Denn die $Moralit{\ddot{a}}t$ ist nicht die einfache Projektion eines subjektiven Zustandes, vielmehr konstruiert die emotionale Reaktion von Billigung oder $Mi{\ss}billigung$ das moralische Urteil. Daher muss der projektistische Gesichtspunkt des expressionistischen Emotivismus modifiziert werden, so $da{\ss}$ der oft dem Emotivismus kritisch zugeschriebene moralische Nihilismus zu ${\ddot{u}}berwinden$ ist. In diesem Zusammenhang $schl{\ddot{a}}g$ Prinz den konstruktiven Sentimentalismus vor, der als eine hybride Theorie des Moralbegriffs von 'biologiscehn Tatsachen' und 'sozialer Konstruktion' darauf zielt, im moralischen Leben eine Stelle auszumanchen, wo Evolution und Kutur zueinander zusammentreffen $k{\ddot{o}}nnen$.

• The Journal of the Korea Contents Association
• /
• v.19 no.4
• /
• pp.359-367
• /
• 2019

For this study, specimens were prepared using five types of composite resin and resin-reinforced glass ionomer Fuji II LC, and 29 days precipitation was done in four kinds of solution, which were soy sauce, gochujang, wine, and distilled water. Ten specimens for each coloring sample were divided into two groups, one those surfaces was polyester film and the other with 1200-grit abrasive paper, and 20 specimens per materials. Color change (${\Delta}{\ast}ab$) in the colored specimens is measured in 2days, 7days, 14days and 29days using spectrophotometer (CM-2600d, Konica, Minolta, Ramsey, NJ). All values were considered significant when P<0.05. 1. Each material is discolored over time under the influence of different storage solutions. 2. In soy source, among the specimens polished with polyester film, color change was observed in resin-modified glass ionomer Fuji II LC, prodigy and compomer F-2000 on day 2. Meanwhile, Fuji II LC showed noticeable color change in specimens prepared with 1200-grit sandpaper on day 2, which was followed by flowable resin on day 7. 3. On day 2, there was a color change with the specimens of flowable resin, resin-modified glass ionomer Fuji II LC and Prodigy among the hybrid specimen in the groups of polyester film in gochujang.

• Journal of Intelligence and Information Systems
• /
• v.18 no.4
• /
• pp.43-57
• /
• 2012

To enhance the competitive advantage in a constantly changing business environment, an enterprise management must make the right decision in many business activities based on both internal and external information. Thus, providing accurate information plays a prominent role in management's decision making. Intuitively, historical data can provide a feasible estimate through the forecasting models. Therefore, if the service department can estimate the service quantity for the next period, the service department can then effectively control the inventory of service related resources such as human, parts, and other facilities. In addition, the production department can make load map for improving its product quality. Therefore, obtaining an accurate service forecast most likely appears to be critical to manufacturing companies. Numerous investigations addressing this problem have generally employed statistical methods, such as regression or autoregressive and moving average simulation. However, these methods are only efficient for data with are seasonal or cyclical. If the data are influenced by the special characteristics of product, they are not feasible. In our research, we propose a forecasting framework that predicts service demand of manufacturing organization by combining Case-based reasoning (CBR) and leveraging an unsupervised artificial neural network based clustering analysis (i.e., Self-Organizing Maps; SOM). We believe that this is one of the first attempts at applying unsupervised artificial neural network-based machine-learning techniques in the service forecasting domain. Our proposed approach has several appealing features : (1) We applied CBR and SOM in a new forecasting domain such as service demand forecasting. (2) We proposed our combined approach between CBR and SOM in order to overcome limitations of traditional statistical forecasting methods and We have developed a service forecasting tool based on the proposed approach using an unsupervised artificial neural network and Case-based reasoning. In this research, we conducted an empirical study on a real digital TV manufacturer (i.e., Company A). In addition, we have empirically evaluated the proposed approach and tool using real sales and service related data from digital TV manufacturer. In our empirical experiments, we intend to explore the performance of our proposed service forecasting framework when compared to the performances predicted by other two service forecasting methods; one is traditional CBR based forecasting model and the other is the existing service forecasting model used by Company A. We ran each service forecasting 144 times; each time, input data were randomly sampled for each service forecasting framework. To evaluate accuracy of forecasting results, we used Mean Absolute Percentage Error (MAPE) as primary performance measure in our experiments. We conducted one-way ANOVA test with the 144 measurements of MAPE for three different service forecasting approaches. For example, the F-ratio of MAPE for three different service forecasting approaches is 67.25 and the p-value is 0.000. This means that the difference between the MAPE of the three different service forecasting approaches is significant at the level of 0.000. Since there is a significant difference among the different service forecasting approaches, we conducted Tukey's HSD post hoc test to determine exactly which means of MAPE are significantly different from which other ones. In terms of MAPE, Tukey's HSD post hoc test grouped the three different service forecasting approaches into three different subsets in the following order: our proposed approach > traditional CBR-based service forecasting approach > the existing forecasting approach used by Company A. Consequently, our empirical experiments show that our proposed approach outperformed the traditional CBR based forecasting model and the existing service forecasting model used by Company A. The rest of this paper is organized as follows. Section 2 provides some research background information such as summary of CBR and SOM. Section 3 presents a hybrid service forecasting framework based on Case-based Reasoning and Self-Organizing Maps, while the empirical evaluation results are summarized in Section 4. Conclusion and future research directions are finally discussed in Section 5.

• Journal of Aquaculture
• /
• v.1 no.1
• /
• pp.67-73
• /
• 1988

A growth experiment of tilapia (offsprings of the hybrid between Oreochromis niloticus and O. mossambicus) under different dissolved oxygen levels in the recirculating water system was conducted at the Fish Culture Experiment Station of the National Fisheries University of Pusan from February 4 to March 5, 1986. Six tanks with a capacity of $1.8m^3$ of water each were used under the same condition of water parameters except for dissolved oxygen levels which were designated to maintain at 1.5, 2.0, 2.5, 3.0, 3.5 and 4.0 mg/$\iota$. Each tank was stocked with 90 kg of fish each averaging 64 to 69 grams. The average water temperature during the course of the experiment was $22.5^{\circ}C$. The results obtained are summarized as follows: The food conversion efficiencies were very good, being 1.05-1.11 at 3.5, 3.0, 2.5 and 2.0 mg/$\iota$ DO levels without any significant differences among them, but at 4.0 mg/$\iota$ the F. C. was 1.39 and at 1.5 mg/$\iota$ it was 1.61 being very poor compared with the others. The daily growth rate performance was best at 3.5 mg/$\iota$ dissolved oxygen level followed by 3.0 and 2.5 mg/$\iota$ with slight differences while at 4.0 and 2.0 mg/$\iota$ DO levels the growths were significantly poor, and at 1.5 mg/$\iota$ DO level it was extremely poor. In 1.5 mg/$\iota$ group, the fish did not accept feed vigorously and after feeding the fish usually concentrated around the inflow point showing oxygen deficiency response. While at 4.0 mg/$\iota$ high feeding rates tended to waste significant amounts of feed while eating and led to water deterioration, and above these levels the results is considered to lead to a waste of energy with uneconomical performance. On the other hand, at and below 2.0 mg/$\iota$ DO level the tilapia certainly showed a poor growth performance. The experiment indicates that the DO range of 2.5$\~$3.5 mg/$\iota$ is the optimum level for the good growth performance.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.2
• /
• pp.196-203
• /
• 2003

The application of sealants is a highly technique-sensitive procedure, requiring an extremely dry field prior to placement. Moisture contamination of the etched enamel surface before sealant placement is cited as the main reason for sealant failure. The purpose of this study was to evaluate the effects of different methods of sealant application on the shear bond strength of sealants to enamel. In groups 1, 2, 3, 4 Teethmate(unfilled sealant) was used, while Ultraseal XTplus(filled sealant) was used in groups 5, 6, 7, 8. Groups 1 and 5(control) were acid etched for 15 seconds using 35% phosphoric acid, washed and then dried. In groups 2, 6 drying agents were applied, and in groups 3, 7 bonding agents were applied and light cured. In groups 4 and 8 both drying agent and bonding agent were applied. Then sealant was cured to the specimen using molds 3mm in diameter and 2mm in height. Thermocycling was performed and shear bond strength was finally measured. The following results were obtained : 1. Groups using filled sealant(groups 5, 6, 7, 8) showed higher shear bond strengths compared to groups using unfilled sealant(groups 1, 2, 3, 4). 2. Among groups using unfilled sealant(groups 1, 2, 3, 4), groups 2, 3, 4 showed significantly higher shear bond strength compared to group 1(p<0.05). There were no significant differences among groups 2, 3 and 4. 3. There were no significant differences(p>0.05) among groups using filled sealant(groups 5, 6, 7, 8). 4. When modes of fracture were examined, cohesive failure was observed in groups 2, 3 and 4.

• Journal of Sericultural and Entomological Science
• /
• v.49 no.1
• /
• pp.14-17
• /
• 2007

A new silkworm variety Golden silk for spring rearing season is $F_1$ hybrid between Jam311, a Japanese race bred from introduction breeding and Jam312, a Chinese race from introduction breeding. In the local adaptability test performed at 8 local areas in spring of 2006, "Golden silk" was showed 7 percent higher in hatchability than authorized silk-worm races laval. "Golden silk" was receded higher 1.7 percent, 2.2 percent in pupation rate, best cocoon rate respectively than Chunsujam. The larval period shortened for 1.12 day even though low record to the several items including productivity than Chunsujam. "Golden silk" was showed 1,031 m, 2.97 denier in length of cocoon filament, weight of cocoon filament respectively. The concentration of Deoxynojirimycin(DNJ) was measured 4.34 mg in "Golden silk", high then to "Chunsujam"(3.81 mg). In the Paecilomyces tenuipes production ability test, the pupal weight of "Golden silk" was 1.20g.

• Current Research on Agriculture and Life Sciences
• /
• v.1
• /
• pp.1-9
• /
• 1983

This study was conducted to obtain basic information on the rice anther culture. Materials used were (Inabawase X YR 2404-14-2-1) $F_1$ hybrid. Callus growth rate on various media, induction frequency of callus in spikelet and panicle, and the effect of treatment on anther and callus were evaluated. The results obtained were summarized as follows ; The growth rate of callus on N-6, M-S, P.E.agar media was 19.8, 13.1, 4.1 times respectively after 30 days inoculated, and on liquid media was 3.8, 5.1, 1.4 times, respectively. Organ differentiation on N-6, M-S, P.E.agar media was 37.5%, 12.5%, 17.5% respectively. The difference of induction frequency of callus per panicle was 0.14%-6.25% and per spikelet was 0-19.05%. Almost callus was induced 30-35 days after inoculation. Organ differentiation of induced callus was decreased by culture. Callus cultured for 13 days after induction did not make shoot. Anthers cold shocked at $8^{\circ}C$ for 5 days obtained 3.32% efficiencys of callus induction per number of anthers plated, and compared with 2.41% of no treated anthers. But anther treated at $8^{\circ}C$ for 7 days decreased 2.24%. Callus induction periods were shortened by cold treatment for about 5 days. Callus cultured on medium containing 2 mg/l of 2, 4-D showed 5% on root formation but medium containing 5 mg/l of 2, 4-D showed 30% of root formation after transfered on the medium without 2, 4-D. Callus cold shocked at $15-18^{\circ}C$ revealed poor efficiency for root formation, but 5 days treatment was good for shoot formation.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.51 no.spc1
• /
• pp.185-192
• /
• 2006

This experiment was conducted to assess genetic diversity of waxy corn inbred lines and to identify SSR markers related to major characteristics affected kernel quality for improving waxy corn $F_1$ hybrid with good quality. Diversity of 64 waxy com inbred lines was evaluated using 30 microsatellite markers. The 30 microsatellite markers representing 30 loci in the maize genome detected polymorphisms among the 64 inbred lines and revealed 225 alleles with a mean of 7.5 alleles per primer. The polymorphism Information content (PIC) value ranged from 0.14 to 0.87, with an average of 0.69. Based on Nei's genetic distances, the 64 inbred lines were classified into 9 groups by the cluster analysis. The group I included 26 inbred lines (41%), other groups included 3 to 9 inbred lines. One-way analysis of variance was conducted to identify significant relationship between individual markers and major characteristics that affect kernel quality. The analysis showed that umc1019 was related to amylopectin and crude protein content, me 1020 to amylopectin content and peak viscosity, and bnlg1537 to 100-kernel weight, kernel length, and kernel width.

• Clinical and Experimental Reproductive Medicine
• /
• v.21 no.2
• /
• pp.165-176
• /
• 1994

This study was carried out to investigate the effect of the timing and dose of human chorionic gonadotropin(hCG) on oocyte recovery, in vitro fertilization, and preimplantation development in superovulation of mouse. F1 hybrid($C57BL{\times}CBA$) mice were obtained and superovulation was induced in female mice by sequential intraperitoneal injection of PMSG and hCG. In the first series of experiments, mice received 5 IU of PMSG given intraperitoneally, and 48 hours later were injected 1 IU, 5 IU, or 10 IU of hCG respectively. In the second series of experiments, mice received 5 IU of PMSG given intraperitoneally and were injected 5IU of hCG 36, 48, or 60 hours later respectively. 1. When the mice received 5 IU of PMSG given intraperitoneally and 48 hours later were injected 1 ItT, 5 IU, or 10 IU of hCG respectively, there were no differences in the total number of the oocytes obtained from the three experimental groups. When the cultures were examined 48 hrs after the termination of insemination the proportion of unfragmented oocytes which had developed over two-cell stage was observer to be lowest in 10 IU hCG group. When the cultrues were examined 120 hour after termination of insemination the proportion of embryos which had developed to the blastocyst stage was observed to be significantly higher in 10IU hCG group than 5IU hCG group(p<0.05), but there was no difference between 10 IU hCG group and 1IU hCG group. 2. When the mice received 5 IU of PMSG and were injected 5 IU of hCG 36, 48, or 60 hours later respectively, there were no differences in the total number of oocytes obtained from the three experimental groups. When cultures were examined 48 hour after the termination of insemination the proportion of unfragmented oocytes which had developed over two-cell stage was observed to be significantly lower in 36 hour interval group than 48 hour interval and 60 hour interval group(p<0.05). When the cultures were examined 120 hour after termination of insemination the proportion of embryos which had developed to the blastocyst stage was found to be higher in 60 hour interval group than 36 interval or 48 hour interval group (P<0.05), and the proportion of hatching blastocyst was found to be higher in 60 hour interval group as well. In this study, it was concluded that the administration of adequate dose of hCG, and long (60 hour) PMSG-hCG interval were necessary in superovulation of mice($C57BL{\times}CBA$) in order to get a large number of oocytes which had an early oocytes which had an early embryonic developmental capability when fertilized in vitro, and especially it had better have been avoided to administer a large dose of hCG.