• 한국표면공학회지
• /
• 제36권5호
• /
• pp.413-417
• /
• 2003

The effect of 0-0.7 ㏖% addition of $Cr_2$$O_3$on the dielectric, pyroelectric, and piezoelectric properties were studied in the (Mg$0.7Pb_{1}$$3/Nb_{2}$3/)$O_3$-$0.3PbTiO_3$(0.7PMN-0.3PT) ceramics with composition near the morphotropic phase boundary. The dielectric constant and loss of the ceramics samples were measured as a function of temperature at various frequencies (0.1-100 KHz). The pyroelectric coefficient was measured by using the Byer-Roundy method as a function of temperature. Dielectric, pyroelectric, and piezoelectric constant achieved the maximum values of 0.4 ㏖% $Cr_2$$O_3$The transition temperature is continuously shifted to lower temperature with an increase of a small amount of $Cr_2$$O_3$.

• 한국세라믹학회지
• /
• 제49권2호
• /
• pp.197-203
• /
• 2012

In this study, in order to improve densification of $La_{0.8}Ca_{0.2}Cr_{0.9}Co_{0.1}O_{3-\delta}$ (LCCC), which is known for one of the most proper candidate interconnector materials in the solid oxide fuel cells, $CaCrO_4$ was prepared via solid oxide synthesis route and added to the LCCC with different amount and particle sizes. As the amount of the $CaCrO_4$ increased, porosity of the sintered samples increased, and the pore size was proportional to the particle size of the $CaCrO_4$. This supports the fact that the $CaCrO_4$ phase forms liquid during sintering and permeate into the matrix leaving behind large pores. Then the liquid reacts with the matrix through the solid solution. However, when the samples were sintered with a slow ramp up rates, the porosity decreased. This is thought to be caused by the progressive solid solution of $CaCrO_4$ before the temperature reach to the melting temperature and forms a fluent amount of liquids. The sintering behavior of the LCCC with the addition of $CaCrO_4$ was analyzed through the transient liquid phase sintering on the basis of the microstructure observation and phase identification by x-ray diffraction.

• Corrosion Science and Technology
• /
• 제19권1호
• /
• pp.43-50
• /
• 2020

In this study, the effects of KCl(s) and K₂SO₄(s) on the oxidation characteristics of 2.25Cr-1Mo steel were investigated for 500 h in 10O₂ + 10CO₂ (vol%) gas environmen at 650 ℃. Oxidation kinetics were characterized by weight gain, oxide layer thickness, and fitted models for the experiment data were proposed. The fitted models presented considerable agreement with the experimental data. The oxide layer was analyzed using the scanning electron microscope, optical microscope, and energy dispersive X-ray spectroscopy. The oxidation kinetics of 2.25Cr-1Mo steel with KCl and K₂SO₄ coatings showed significantly different oxidation kinetics. KCl accelerated the oxidation rate very much and had linear oxidation behavior. In contrast, K₂SO₄ had no significant effect, which had parabolic kinetics. The oxide layer was commonly composed of Fe₂O₃, Fe₃O₄, and FeCr₂O₄ spinel. KCl strongly accelerated the oxidation rates of 2.25Cr-1Mo steel in the high-temperature oxidation environment. Conversely, K₂SO₄ had little effect on the oxidation rates.

• 한국표면공학회지
• /
• 제42권2호
• /
• pp.68-72
• /
• 2009

We report on the growth of $CuCrO_2$ films using pulsed laser deposition and their structural and electrical transport properties. $CuCrO_2$ thin films were doped with 5 at% Mg for p-type properties. Epitaxial films of $CuCr_{0.95}Mg_{0.05}O_2$ were grown on c-plane sapphire substrates. The effects of growth temperature and oxygen pressure on film properties were investigated. The main phase of delafossite $CuCr_{0.95}Mg_{0.05}O_2$ was appeared above the growth temperature of $600^{\circ}C$. The thin film grown at $500^{\circ}C$ showed the highest conductivity, reaching 19.6 S/cm while higher growth temperatures over $500^{\circ}C$ led to lower conductivity; the thin film grown at $700^{\circ}C$ showed 0.02 S/cm.

• 한국압력기기공학회 논문집
• /
• 제7권2호
• /
• pp.26-33
• /
• 2011

To evaluate steam oxidation behaviours of Alloy 617 and Haynes 230, oxidation test were performed at $900^{\circ}C$ in steam and $steam+20\;vol.-%\;H_2$ environments. Oxidation rate in steam condition was similar to that in air for Alloy 617, while it was slightly lower for Haynes 230. When hydrogen was added to steam, oxidation rate was enhanced. Isolated $MnTiO_3$ particle were formed on $Cr_2O_3$ oxide layer and sub layer $Cr_2O_3$ were formed in steam and $steam+20\;vol.-%\;H_2$ for Alloy 617. On the other hands, $MnCr_2O_3$ layer were formed on top of $Cr_2O_3$ oxide layer for Haynes 230. The extensive sub layer $Cr_2O_3$ formation was resulted from the oxygen inward diffusion in such environments. When hydrogen was added, the oxide morphology was changed from polygonal to platelet because of the accelerated diffusion of cations under the oxide layer. In addition, decarburized zone was extended as hydrogen participated into the reactions causing carbide dissolution.

• 한국환경과학회지
• /
• 제31권8호
• /
• pp.677-689
• /
• 2022

In order to photocatalytically treat organic matter (COD_Cr) and chromaticity effectively, chemical coagulation and sedimentation processes were employed as a pretreatment of the leachate produced from landfill in Jeju Island. This was performed using FeCl₃·6H₂O as a coagulant. For the treated leachate, UV/TiO₂ and UV/TiO₂/H₂O₂ systems were investigated, using 4 types of UV lamps, including an ozone lamp (24 W), TiO₂ as a photocatalyst, and/or H₂O₂ as an initiator or inhibitor for photocatalytic degradation. In the chemical coagulation and sedimentation process using FeCl₃·6H₂O, optimum removal was achieved with an initial pH of 6, and a coagulant dosage of 2.0 g/L, culminating in the removal of 40% COD_Cr and 81% chromaticity. For the UV/TiO₂ system utilizing an ozone lamp and 3 g/L of TiO₂, the optimum condition was obtained at pH 5. However, the treated COD_Cr and chromaticity did not meet the emission standards (COD_Cr: 400 mg/L, chromaticity: 200 degrees) in a clean area. However, for a UV/TiO₂/H₂O₂ system using 1.54 g/L of H₂O₂ in addition to the above optimum UV/TiO₂ system, the results were 395 mg/L and 160 degrees, respectively, which were within the emission standard limits. The effect of the UV lamp on the removal of COD_Cr, and chromaticity of the leachate decreased in the order of ozone (24 W) lamp > 254 nm (24 W) lamp > ozone (14 W) lamp > 254 nm (14 W) lamp. Only COD_Cr and chromaticity treated with the ozone (24 W) lamp met the emission standards.

• 한국지반환경공학회 논문집
• /
• 제7권3호
• /
• pp.21-29
• /
• 2006

난분해성 염색폐수를 처리하기 위한 화학적 처리 방법으로 오존단독처리와 3가지 경우의 고도산화공정[AOPs($O_3/H_2O_2$, $O_3/UV$, $O_3/H_2O_2/UV$)]의 처리특성을 실험적으로 검토하였다. 각각의 처리방법에서 합성 염색폐수를 대상으로 $COD_{cr}$ 및 색도의 제거효율, 생분해도(biodegradability)향상에 대한 처리특성을 상대적으로 비교 평가하였고 pH, 온도, 주입량, 순환유량 등을 주요운전인자로 하여 각 산화공정의 최적운전 조건을 파악하였다. 대상으로 한 모든 공정에서 염색폐수의 색도는 단시간에 대부분 제거되었지만, $COD_{cr}$ 제거측면과 생분해도 향상에서는 $O_3/H_2O_2/UV$ 공정이 가장 좋은 처리효율을 나타냈다.

• 자원리싸이클링
• /
• 제16권6호
• /
• pp.3-9
• /
• 2007

생활 폐기물은 대부분 유리류와 자기류뿐만 아니라 많은 양의 iron을 함유하고 있으며 약 $3{\sim}11%$에 달한다. 대부분의 iron은 Ni-Fe와 Ni-Cr-Fe 같은 합금으로 존재하거나, 부식방지와 광택을 위해 Ni와 Cr로 도금된 iron으로 존재하고 있기 때문에 소각로에서 소각될 경우 철 재품 표면에 심하게 파손된 $Fe_3O_4$층과 함께 $NiFe_2O_4$와 FeCr_2O_4$을 형성하게 되어 바닥재에 존재하게 되어 중금속산화물 층을 형성시킬 수 있다. iron은 자력이 매우 강해 자력선별에 의해 쉽게 선별되며 이러한 효과로 인해 중금속 산화물의 선별까지 얻을 수 있다. 또한 바닥재는 다양한 Ni와 Cr 산화물들을 함유하고 있으며, Ni와 Cr은 강자성을 띈 물질이기 때문에 자력선별에 의해 큰 영향을 받을 수 있다. 따라서 자력선별에 따른 Ni와 Cr의 거동에 대해 조사하였으며 그 밖의 다른 중금속(Cu, Pb, Cd, As)들의 거동 또한 확인해 보았다. 그 결과 Ni와 Cr은 약 $45{\sim}50%$의 선별율을 보였으며, Cu와 Pb는 $15{\sim}20%$을 나타냈다. 또한 자력선별 전과 후의 바닥재에 대해 Ni와 Cr의 용출량을 확인해본 결과 자력선별 후 바닥재의 용출량이 더 낮음을 확인할 수 있었다.

• 상하수도학회지
• /
• 제29권1호
• /
• pp.33-38
• /
• 2015

In this study, flat-type photocatalytic reaction system is applied to reduce toxic hexavalent chromium (Cr(VI)) to trivalent chromium (Cr(III)) in aqueous solution under UV irradiation. To overcome the limitation of conventional photocatalysis, a novel approach toward photocatalytic system for reduction of hexavalent chromium including nanotubular $TiO_2$ (NTT) on two kinds of titanium substrates (foil and mesh) were established. In addition, modified Ti substrates were prepared by bending treatment to increase reaction efficiency of Cr(VI) in the flat-type photocatalytic reactor. For the fabrication of NTT on Ti substrates, Ti foil and mesh was anodized with mixed electrolytes ($NH_4F-H_2O-C_2H_6O_2$) and then annealed in ambient oxygen. The prepared NTT arrays were uniformly grown on two Ti substrates and surface property measurements were performed through SEM and XRD. Hydraulic retention time(HRT) and substrate type were significantly affected the Cr(VI) reduction. Hence, the photocatalytic Cr(VI) reduction was observed to be highest up to 95% at bended(modified) Ti mesh and lowest HRT. Especially, Ti mesh was more effective as NTT substrate in this research.

• 전기화학회지
• /
• 제14권1호
• /
• pp.27-32
• /
• 2011

Cr을 첨가한 $Li_4Ti_5O_{12}$의 전기화학적 특성을 고찰하였다. 산화물에 금속원자가 치환될 경우에 결정구조가 변화되며, $Li_4Ti_5O_{12}$의 전기화학적 특성이 변화하게 된다. 졸-겔법을 이용하여 $Li_4Ti_{5-x}Cr_xO_{12}$ (x = 0~0.2)를 제조하였으며, 전기로에서 $800{\sim}850^{\circ}C$로 공기중에서 12시간 동안 열처리하였다. 시료의 물리적인 특성은 TG-DTA, XRD, SEM, FT-IR을 사용하여 측정하였으며, 전기화학적인 특성은 0.01~2.0V의 범위에서 배터리충방전기를 사용하여 측정하였다. $Li_4Ti_5O_{12}$는 1C에서 169.9 mAh/g의 용량을 나타내었으며, 0.1C로 변화되었을 경우에 초기용량의 97.5%를 나타내었다. $Li_4Ti_{4.9}Cr_{0.1}O_{12}$ 시료는 1C에서 193.8 mAh/g의 용량을 보였으며, 0.1C에서는 초기용량의 98.8%를 나타내었다.