• Membrane Journal
• /
• v.20 no.4
• /
• pp.290-296
• /
• 2010

Ethylene vinyl acetate (EVA-28)/Co-Al LDH nanocomposite membranes were prepared by solution intercalation using organically modified LDH. LDH was made organophilic by the intercalation of dodecyl sulfate (DS) anion in the interlayer. The prepared membranes were characterized using XRD, FT-IR and SEM. Gas permeability of EVA/LDH nanocomposite membranes with LDH content of 1, 3, and 5 w% was studied for $O_2$ and $CO_2$ at pressure of 3, 4, and 5 bar. The permeability of $O_2$ and $CO_2$ was minimum for nanocomposite membrane with 1 wt% LDH and increased with increasing LDH content, which is presumably due to aggregation of LDH filler. The selectivity of $CO_2$ for $O_2$ showed the maximum value at 1 wt% of LDH content and decreased thereafter.

• Advances in Energy Research
• /
• v.2 no.2
• /
• pp.97-104
• /
• 2014

A co-spray deposition technique has been developed to bypass a fundamental limitation in the conventional spray deposition technique, i.e., the deposition of metal oxides from incompatible precursors in the starting solution. With this technique, ZnO films codoped with F and Al have been successfully synthesized, in which F is incompatible with Al. Two starting solutions were prepared and co-sprayed through two separate spray heads. One solution contained only the F precursor, $NH_4F$. The second solution contained the Zn and Al precursors, $Zn(O_2CCH_3)_2$ and $AlCl_3$. The deposition was carried out at $500^{\circ}C$ on soda-lime glass in air. A minimum sheet resistance, $55.4{\Omega}/{\square}$, was obtained for Al and F codoped ZnO films after vacuum annealing at $400^{\circ}C$, which was lower than singly-doped ZnO with either Al or F. The transmittance for the codoped ZnO samples was above 90% in the visible range. This co-spray deposition technique provides a simple and cost-effective way to synthesize metal oxides from incompatible precursors with improved properties for photovoltaic applications.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.727-730
• /
• 2009

Highly active and stable nano-sized Ni catalysts supported on MgO-$Al_2O_3$ calcined from hydrotalcite-like materials have been successfully developed with a strong metal to support interaction (SMSI) to enhance the coke resistance in combined $H_2O$ and $CO_2$ reforming of $CH_4$ (CSCRM) for syngas ($H_2$/CO=2) production. The change of the surface area and NiO crystallite size with varying the pre-calcination temperature of support and Mgo content was investigated in relation to the coke resistance. As increasing the pre-calcination temperature, the surface area decreases and the metal to support interaction becomes weak. As a consequence, the coke deposition was more severe on catalysts pre-calcined at high temperature. It was concluded that highly dispersed Ni metal in the surface of Ni/MgO-$Al_2O_3$ catalyst (MgO=30 wt%) pre-calcined at $800^{\circ}C$ had a strong metal to support interaction (SMSI) resulting in an increase of coke resistance and high activity.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.3
• /
• pp.757-767
• /
• 2018

In the propane dehydrogenation reaction proceeding at high temperature, the main cause of deactivation of the catalyst is coke deposition and sintering. In order to investigate the catalysts for reducing such inactivation, we have investigated the applicability of $MgAl_2O_4$ as a carrier for the catalytic dehydrogenation reaction. $MgAl_2O_4$ was prepared by Alcohthermal method at calcination temperature of 800, 900, $1000^{\circ}C$, and $Pt-Sn/MgAl_2O_4$ catalyst was prepared by supporting Pt and Sn by co-impregnation method. The reaction temperature was conducted at a high temperature of 650, $600^{\circ}C$ to confirm the thermal stability. As a result of the reaction experiment, it was confirmed that the conversion rate and yield of propane dehydrogenation reaction test were higher than that of the carrier-applied catalyst having a carrier calcination temperature of 900 and $1000^{\circ}C$, when the carrier-applied catalyst having a calcination temperature of $800^{\circ}C$ was used, It was found that the yield was higher than that of $Pt-Sn/{\theta}-Al_2O_3$ at $650^{\circ}C$. TGA, BET, XRD, CO-chemisorption, and SEM-EDS analyzes were performed for characterization. $MgAl_2O_4-800^{\circ}C$ was correlated with the relationship between good yield, Pt dispersion and low deactivation rate.

• Clean Technology
• /
• v.13 no.4
• /
• pp.287-292
• /
• 2007

[ $M/Al_2O_3$ ] (M = Mn, Fe, Co, Ni, Cu) catalysts supported on commercial alumina ($Al_2O_3$) were prepared by an impregnation method, and were applied to the hydrogen production by auto-thermal reforming of ethanol. It was revealed that each catalyst retained its own metallic phase and product distribution strongly depended on the identity of active metal. Among the catalysts prepared, $Ni/Al_2O_3$ and $Co/Al_2O_3$ showed the best catalytic performance in the auto-thermal reforming of ethanol. However, the reaction mechanisms over these two catalysts were different. Ni/Al_2O_3 catalyst showed 100% ethanol conversion at $500^{\circ}C$, but it exhibited a rapid decrease in hydrogen selectivity. Although $Co/Al_2O_3$ catalyst showed an excellent performance in hydrogen selectivity, on the other hand, no significant improvement in hydrogen yield was observed due to the low ethanol conversion over the catalyst.

• Korean Chemical Engineering Research
• /
• v.45 no.5
• /
• pp.506-514
• /
• 2007

To select the best oxygen carrier particle for syngas fueled chemical-looping combustor, the reduction reactivity and carbon deposition characteristics were determined in a thermogravimetric analyzer. Four kinds of oxygen carrier particles (NiO/bentonite, $NiO/LaAl_{11}O_{18}$, $Co_xO_y/CoAl_2O_4$, $NiO/NiAl_2O_4$) were tested with the simulated syngas (30% $H_2$, 10% $CO_2$, 60% CO) as a reduction gas. With each of these particles, the maximum conversion and oxygen transfer capacity increase with increasing the reduction temperature At the given experimental range, the optimum operating temperature to maximize oxygen transfer rate is found to be $900^{\circ}C$ and carbon deposition on the particles could avoid at the temperature above $800^{\circ}C$. Among four kinds of oxygen carrier particles, the NiO-based particles exhibits better reactivity than the CoO-based particle. Moreover, the NiO/bentonite particle produces the best reactivity based on the oxygen transfer rate and the degree of carbon deposition. The measured oxygen transfer rate increases as the metal oxide content in NiO/bentonite particle is increased thereby higher metal oxide contents could provide stable operation of chemical-looping combustor.

• Korean Journal of Materials Research
• /
• v.17 no.11
• /
• pp.612-617
• /
• 2007

Both photoluminescence and thermal characteristics for $SrAl_2O_4:Eu^{+2},\;Dy^{+3}$ phosphors synthesized with various aluminum compounds (${\alpha}-Al_2O_3$, ${\gamma}-Al_2O_3$, amorphous-$Al_2O_3$ and $Al(OH)_3)$ were investigated in this study. The formation temperature of the host $SrAl_2O_4$ crystal is changed by these various aluminum compounds, as a result of the different thermal decomposition temperature of $SrCO_3$ phase. Among these compounds, the amorphous-$Al_2O_3$ phase shows the lowest formation temperature of the host $SrAl_2O_4$ crystal. The PL emission and excitation spectra of $SrAl_2O_4:Eu^{+2},\;Dy^{+3}$ phosphor are not affected by these aluminum compounds. After the removal of the Xenon lamp excitation (360 nm), however, the excellent longphosphorescent property of the phosphor is obtained by the amorphous-$Al_2O_3$ phase, although the decay time for all phosphors decrease exponentially.

• Korean Journal of Materials Research
• /
• v.24 no.2
• /
• pp.93-97
• /
• 2014

In this study, a cobalt sulfate ceramic coating was sintered on various clays at $1250^{\circ}C$. The specimen characteristics were investigated by X-ray diffraction(XRD), scanning electron microscopy(SEM), TG-DTA, UV-vis spectrophotometer, and HRDPM. The ceramic coating had a constant thickness of thousands ${\mu}m$, and the surface was confirmed to be densely fused. Other new compounds were produced by the cobalt sulfate sintering process and reactions. These compounds were a $CoAl_2O_4$ phase, $Co_2SiO_4$ phase, anorthite($CaAl_2Si_2O_8$) phase, and $FeAl_2O_4$ phase, respectively. UV properties of the coated specimen were investigated, celadon clay specimen in 530-550 nm band is showing a dark gray color. The white clay and white mix clay specimen in 460-500 nm band is showing a blue color. The cobalt-aluminate($CoAl_2O_4$) spinel and the cobalt-silicate olivine($Co_2SiO_4$) were the strongest of the ceramic pigments, producing a very pure, navy blue color.

• The Korean Journal of Ceramics
• /
• v.5 no.4
• /
• pp.371-374
• /
• 1999

Y2O3 and Nb2O5 co-doped tetragonal zirconia polycrystals((Y, Nb)-TZP) containing 10 to 30 vol% $Al_2O_3$ were prepared and hydrothermal stability of the composites was evaluated after aging for 5 h at the temperature range of $150^{\circ}C$ $250^{\circ}C$ under 4 MPa $H_2O$ vapor pressure in an autoclave. The (Y, Nb)-TZP/Al2O3 composites showed excellent phase stability under the hydrothermal conditions, as compared with the 3Y-TZP/$Al_2O_3$ composites, due to the combined effects of the Y-Nb ordering in the $t-ZrO_2$ lattice, the reduction of oxygen vacancy concentration, and the $Al_2O_3$ addition. The strength and fracture toughness of the (Y, Nb)-TZP/$Al_2O_3$ composite, containing 20 vol% of 2.8 $Al_2O_3$ particles, were 700 MPa and 8.1 MP.$am^{1/2}$, respectively.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2007.05a
• /
• pp.526-529
• /
• 2007

본 연구에서는 일정선량(600kGy)에서 전자빔 에너지(0.7, 1, 2 MeV)를 달리하여 조사한 $Ni/g-Al_2O_3$ 촉매를 이용하여 세 가지 다른 종류의 합성가스 전환반응(메탄의 이산화탄소 개질반응, 메탄의 수증기 개질반응, 메탄의 부분산화반응)을 수행하였다. 전자빔 조사는 He 분위기, 실온에서 수행하였으며, 조사된 촉매의 표면상태 변화를 살펴보기 위하여 XRD, XPS 분석을 수행하였다. 고에너지 전자빔 처리된 $Ni/g-Al_2O_3$ 촉매의 표면 특성분석 결과 촉매 표면의 Ni종은 metallic Ni, NiO, $NiAl_2O_4$의 3가지 상태로 존재함을 알 수 있었으며, 전자빔 에너지 증가에 따라 촉매 표면의 전체적인 Ni 함량과 촉매 표면의 Ni 분산도를 나타내는 Ni/Al ratio가 증가하였다. 또한, 전자빔 에너지 증가에 따라 Ni에 결합된 산소가 더 크게 감소되어 표면에서 산소 vacancy가 증가하는 결과를 가져왔으며, 이는 결국 세 가지 Ni의 상태 중 metallic Ni과 $NiAl_2O_4$를 증가시켰다. 이러한 결과들은 메탄의 이산화탄소 개질 반응과 메탄의 수증기 개질반응에서 반응물($CH_4$, $CO_2$)의 전환율과 생성물(CO, $H_2$)의 수득율을 증가시켰으며 메탄의 부분산화반응은 반응의 특성상 메탄의 전환율은 증가하나 생성물인 CO, $H_2$는 오히려 감소하는 결과를 가져옴을 알 수 있었다.