• 한국세라믹학회지
• /
• 제43권6호
• /
• pp.369-375
• /
• 2006

[ $(Ba_{0.5}Sr_{0.5})_{0.99}Co_{x}Fe_{1-x}O_{3-{\delta}}$ ] [x=0.8, 0.2](BSCF) powders were synthesized by a Glycine-Nitrate Process (GNP) and the electrochemical performance of the BSCF cathode on a scandia stabilized zirconia, $[(Sc_{2}O_3)_{0.11}(ZrO_2)_{0.89}]-1Al_{2}O_3$ was investigated. In order to prevent unfavorable solid-state reactions between the cathode and zirconia electrolyte, a GDC ($Gd_{0.1}Ce_{0.9}O_{2-{delta}}$) buffer layer was applied on ScSZ. The BSCF (x = 0.8) cathode formed on GDC(Buffer)/ScSZ(Disk) showed poor electrochemical property, because the BSCF cathode layer peeled off after the heat-treatment. On the other hand, there were no delamination or peel off between the BSCF and GDC buffer layer, and the BSCF (x = 0.2) cathode exhibited fairly good electrochemical performances. It was considered that the observed phenomenon was associated with the thermal expansion mismatch between the cathode and buffer layer. The ohmic resistance of the double layer cathode was slightly lower than that of the single layer BSCF cathode due to the incorporation of platinum particle into the BSCF second layer.

• 자원환경지질
• /
• 제38권4호
• /
• pp.481-492
• /
• 2005

이 연구에서는 광주지역 하상퇴적물에 대한 지질집단별 지구화학적 특성에 대해 규명 하고자 한다. 이를 위해 물이 흐르고 있는 1차 수계를 대상으로 하상퇴적물시료 104개를 채취하였고, 실험실에서 자연건조 시켰다. 화학분석을 위한 시료는 알루미나 몰타르를 이용하여 200메쉬 이하로 분쇄하였고, XRF ICP-AES, NAA분석을 실시하였다. 연구지역 하상퇴적물에 대해, 지질집단별 지구화학적 특성 비교와 기존 암석에 대한 연구에서 얻어진 암석화학적인 특성과의 비교를 위해, 선캠브리아기 화강편마암 지역, 쥬라기 화강암 지역, 백악기 화순안산암 지역으로 분리하였다 광주지역 하상퇴적물의 주성분원소 함량은 $SiO_2\;51.89\~70.63\;wt.\%,\;Al_2O-3\;12.91\~21.95\;wt.\%,\;Fe_2O_3\;3.22\~9.89\;wt.\%,\;K_2O\;1.85\~4.49\;wt.\%,\;MgO\;0.68\~2.90\;wt.\%,\;Na_2O\;0.48\~2.34\;wt.\%,\;CaO\;0.42\~6.72\;wt.\%,\;TiO_2\;0.53\~l.32\;wt.\%,\;P_2O_5\;0.06~0.51\;wt.\%\;and\;MnO\;0.05\~0.69\;wt.\%.$이다. 하상퇴적물과 암석에 대한 AMF 삼각도에서, 암석은 칼크-알칼리계열에 도시되는데 비하여, 하상퇴적물은 솔레아이트 계열과 칼크-알칼리계열의 경계부위에 도시된다. 이는 $Fe_2O_3$ 함량이 암석에서보다 하상퇴적물에 더 많이 함유되어 있는 것과 관련이 있는 것으로 보인다. $SiO_2$에 대한 $K_2O+Na_2O$의 비교그림에서, 하상퇴적물은 암석에서와 같이 subalkaline 계열에 점시된다. 하상퇴적물의 미량성분원소 및 희토류 원소 함량은 $Ba 590\~2170ppm$, Be$1\~2.4$ppm, Cu $13\~179ppm$, Nb $20\~34ppm$, Ni$10\~50ppm$, Pb $17\~30$ppm, Sr $70\~1025$ ppm, V$42\~135$ ppm, Zr$45\~171$ ppm, Li$19\~77$ppm, Co$4.3\~19.3$ppm, Cr$28\~131$ppm, Cs$3.1\~17.6$ ppm, Hf $5\~27.6$ ppm, Rb $388\~202$ ppm, Sb$0.2\~l.2$ ppm, Sc$6.4\~17$ ppm, Zn $47\~389$ ppm, Pa $8.8\~68.8$ ppm, Ce$62\~272$ppm, Eu$1\~2.7$ppm and Yb$0.9\~6$ppm의 범위를 보인다.

• 한국전기전자재료학회논문지
• /
• 제30권6호
• /
• pp.372-375
• /
• 2017

ZnO thin films were deposited by RF magnetron sputtering and then diffused by using an As source in the ampouletube. Also, the ZnO p-n homojunction was made by using As-doped ZnO thin films, and its properties were analyzed. After the As doping, the surface roughness increased, the crystal quality deteriorated, and the full width at half maximum was increased. The As-doped ZnO thin films showed typical p-type properties, and their resistivity was as low as $2.19{\times}10^{-3}{\Omega}cm$, probably because of the in-diffusion from an external As source and out-diffusion from the GaAs substrate. Also, the ZnO p-n junction displayed the typical rectification properties of a p-n junction. Therefore, the As diffusion method is effective for obtaining ZnO films with p-type properties.

• 한국전기전자재료학회논문지
• /
• 제30권7호
• /
• pp.441-446
• /
• 2017

Aluminum nitride fibers were synthesized by carbothermal reduction and nitridation of precursor fibers obtained by electrospinning. The starting materials used to synthesize the AlN fibers were $Al(NO_3)_3{\cdot}9H_2O$ and urea. Polyvinylpyrrolidone with increasing viscidity was used as the carbon source to obtain a composite solution. The mixed solution was drawn into a plastic syringe with a stainless steel needle, which was used as the spinneret and connected to a 20 kV power supply. A high voltage was supplied to the solution to facilitate the formation of a dense net of fibers on the collector. The precursor fibers were dried at $100^{\circ}C$ and then heated to $1,400^{\circ}C$ for 1 h in a microwave furnace under $N_2$ gas flow for the carbothermal reduction and nitridation. X-ray diffraction studies indicated that the synthesized fibers consisted of the AlN phase. Field emission scanning electron microscopy studies indicated that the diameter of the calcined fibers was approximately 100 nm.

• 한국수소및신에너지학회논문집
• /
• 제21권5호
• /
• pp.412-418
• /
• 2010

Steam reforming of n-hexadecane, a major component of diesel over Ni-based hydrotalcite-like catalyst was carried out at $900^{\circ}C$ at atmospheric pressure with space velocity of $10,000h^{-1}$ and feed molar ratio of steam/carbon=3.0. Ni-based hydrotalcite catalyst was prepared by a solid phase crystallization (spc) method and characterized by $N_2$-physisorption, CO chemisorption, TPR., XRD, and TEM techniques. It was found that spc Ni/MgAl catalyst showed higher catalytic stability and inhibition of carbon formation than Ni/$\gamma-Al_2O_3$ catalyst under the tested conditions. The results suggest that the modified spc-Ni/MgAl catalyst after optimization may be applied for the SR reaction of diesel.

• 한국결정성장학회지
• /
• 제22권1호
• /
• pp.1-4
• /
• 2012

O- and Zn-polar ZnO films were grown by DC magnetron sputtering. Growth of high-quality, single-crystal ZnO thin films were confirmed by XRD and pole figure analysis. O-polar ZnO was grown on an $Al_2O_3$ substrate, which was confirmed by a slow growth rate (378 nm/hr), a fast etching rate (59 nm/min), and by the hillocks on the surface after etching. Zn-polar ZnO was grown on a GaN/$Al_2O_3$ substrate, which was confirmed by a fast growth rate (550 nm/hr), a slow etching rate (28 nm/min), and by pits on the surface after etching. Results from the present study show that it is possible to use DC-sputtering to grow ZnO film with the same polarity as other epitaxial growth methods.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.399-399
• /
• 2009

CIS계 화합물 태양전지는 높은 광흡수계수와 열적 안정성 및 Ga 조성 조절을 통한 밴드갭 조절이 용이해 고효율 박막 태양전지로 각광 받고 있다. CIS 태양전지의 광 흡수층 제조 방법으로는 여러 가지 방법이 있지만 본 연구에서는 가장 높은 에너지 변환 효율을 달성한 Co-Evaporation 방법을 사용하기로 하였다. 미국의 NREL의 경우 Co-Evaporation 방법을 사용해 20%의 에너지 변환 효율을 달성한 바가 있다. 하지만 이러한 효율의 태양전지는 실험실에서 연구용으로 제작한 아주 작은 면적으로 태양전지 양산화에 그대로 적용하기는 힘들다. 따라서 CIGS 태양전지의 양산화 적용을 위해 대면적화가 필수적이다. 본 연구에서는 기존의 3 stage 방식을 이용해 광흡수층을 증착하여 최적화 조건을 연구하였다. 또한 기판의 면적 증가에 따라 효율과 Voc, Jsc, F.F가 얼마나 감소하는지 실험하여 보았다. 기판은 soda lime glass를 사용 하였으며 후면 전극으로 약$1{\mu}m$ 두께의 Mo를 DC Supptering 방법을 이용해 증착하였다. 다음으로 약 $2{\mu}m$이상의 광흡수층을 Co-Evaporation 방법을 이용하여 증착 하였으며 buffer층으로는 약 50nm의 CdS층을 CBD방법을 이용하여 제조 하였다. TCO층으로 약 50nm의 i-ZnO와 약 450nm의 Al-ZnO를 RF Sputtering 방법을 이용하여 증착 하였다. 마지막으로 앞면 전극으로 약 $3{\mu}m$의 Al을 Thermal Evaporation 방법으로 증착하였다. 태양전지 소자의 면적은 $0.49cm^2$, $25cm^2$, $100cm^2$로 각각 면적을 달리하며 효율을 비교 분석하였다.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권3호
• /
• pp.512-521
• /
• 2017

This paper reports development process of a university-based sounding rocket using simplified hybrid rocket propulsion system for low-altitude flight application. A hybrid propulsion system was tried to be designed with as few components as possible for more economical, simpler and safer propulsion system, which is essential for the small scale sounding rocket operation as a CanSat carrier. Using blow-down feeding system and catalytic ignition as combustion starter, 250 N class hybrid rocket system was composed of three components: a composite tank, valves, and a thruster. With a composite tank filled with both hydrogen peroxide($H_2O_2$) as an oxidizer and nitrogen gas($N_2$) as a pressurant, the feeding pressure was operated in blowdown mode during thruster operation. The $MnO_2/Al_2O_3$ catalyst was fabricated for propellant decomposition, and ground test of propulsion system showed the almost theoretical temperature of decomposed $H_2O_2$ at the catalyst reactor, indicating sufficient catalyst efficiency for propellant decomposition. Auto-ignition of the high density polyethylene(HDPE) fuel grain successfully occurred by the decomposed $H_2O_2$ product without additional installation of any ignition devices. Performance test result was well matched with numerical internal ballistics conducted prior to the experimental propulsion system ground test. A sounding rocket using the developed hybrid rocket was designed, fabricated, flight simulated and launch tested. Six degree-of-freedom trajectory estimation code was developed and the comparison result between expected and experimental trajectory validated the accuracy of the developed trajectory estimation code. The fabricated sounding rocket was successfully launched showing the effectiveness of the simplified hybrid rocket propulsion system.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.479.1-479.1
• /
• 2006

• 설비공학논문집
• /
• 제10권3호
• /
• pp.334-342
• /
• 1998

In this experimental study, methanol was chosen as a system material for a long -distance heat transportation. Not only transition metals but also noble metals were investigated as an active component, and several metal oxides, such as ${\gamma}$-$Al_2$,$O_3$, $SiO_2$, etc. as a support. In general, transition metal catalysts absorbed more heat than noble metal catalysts. The amount of heat absorption and CO selectivity depends on temperature and methanol partial pressure, and 25$0^{\circ}C$ Ni/$SiO_2$ catalyst showed the best result for methanol decomposition reaction.