• Journal of the Korean Applied Science and Technology
• /
• v.31 no.3
• /
• pp.352-358
• /
• 2014

We were investigated the stability through the electrochemical characteristics of saturated fatty acid(C12, C14, C16, C18) monolayer LB films by cyclic voltammetry. Saturated fatty acid monolayer LB films was deposited on the indium tin oxide(ITO) glass by the LB method. The electrochemical properties were measured by cyclic voltammetry with a three-electrode system in 0.1 N $NaClO_4$ solution. The measuring range was continuously oxidized to 1650 mV, with an initial potential of -1350 mV was reduced. Scanning rates of 50, 100, 150, 200, and 250 mV/s were set. As a result, LB monolayer films of saturated fatty acid were appeared on irreversible processes by the oxidation current from the cyclic voltammogram. Diffusion coefficient(D) of saturated fatty acid(C12, C14, C16, and C18) was calculated 22.231, 2.461, 7.114 and 2.371 ($cm^2s^{-1}{\times}10^{-4}$) in 0.1 N $NaClO_4$ solution, respectively.

• Fire Science and Engineering
• /
• v.22 no.3
• /
• pp.188-193
• /
• 2008

Numerical simulation was carried out for a propane fire of mass transfer rate 3g/m^2-s$ on a 1m high vertical wall. The objectives of this study are to confirm the outcomes of evaluation of the simulator through simulation of natural convection, and to compare the results of the wall fire with those of previous studies. It was confirmed that the simulated boundary layer was laminar at C_s=0.2$ while it was turbulent at C_s=0.1$. The z direction velocity showed lack of turbulent mixing as seen in the natural convection case, and the profiles of temperature and velocities were in relatively good agreement with those of experiment and previous simulation. It was found that the air entrainment into the boundary layer was well predicted.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.96-97
• /
• 2015

확산을 이용한 표면 개질법인 Thermo-Reactive Diffusion(TRD) 기술 기반 2단 표면처리를 통해 고경도의 Nb(C,N) 코팅층을 고탄소 베어링강인 JIS-SUJ2강에 형성시켰다. 2단 표면처리는 암모니아 가스 질화와 분말 확산 코팅법으로 구성된 2step 열처리이다. 본 연구에서는 가스질화 화합물층의 두께가 코팅층 성장 거동에 어떤 영향을 미치는지 알아보기 위해서 $550^{\circ}C$에서 3, 6시간 암모니아 가스 분위기에서 가스질화를 실시하고, $900^{\circ}C$에서 3시간 분말 확산법을 통해 표면 코팅층을 형성하였다. 생성된 코팅층의 형상과 두께 측정을 광학현미경(OM) 과 주자전자현미경(SEM)을 통해 한 결과, 가스 질화는 약 10uu와 16um, 최종 코팅층은 약 정도 생성이 되었음을 확인하였다. 코팅층의 성분 분석은, EDS, FE-EPMA, XPS 분석을 통해서 실시하였다. EDS와 FE-EPMA 원소 mapping을 통해 모재에 비해 높은 농도의 Nb, C 그리고 N이 코팅층 내부에 존재함을 확인하였다. XPS분석의 결합에너지 peak를 통해 NbC, NbN 그리고 Nb-oxide가 생성이 되었음을 분석하였다. 생성된 코팅층의 경도는 low mode에서 10회 측정한 후 평균값을 내었고, 각각 Hv이었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.171.1-171.1
• /
• 2016

재료의 표면 강화 방법 중의 하나인 질화공정을 이용하여 탄소강 S45C 소재의 질화 거동에 대하여 연구하였다. $520^{\circ}C$ 온도에서 질화 공정을 진행하여 공정시간에 따른 Kn값을 수소 센서로 측정하여 공정시간에 따른 N-potential의 변화와 그에 따른 화합물층 성장 및 화합물층의 상변화에 대해 관찰하였다. 화합물 층의 미세구조 변화는 광학현미경 및 주사전자현미경을 통해 관찰하였다. 가스 질화 처리 후 표면경도는 약 600Hv의 경도값이 측정되었고, 공정 시간이 늘어남에 따라 화합물층 및 경화깊이가 증가되고 표면 화합물이 성장하여 porous가 감소하는 것을 확인 할 수 있다. 경화깊이는 1440분 일 때 약 0.5mm 경화 깊이를 얻었고, 화합물층의 성장은 ${\varepsilon}$상(Fe2-3N)과 ${\gamma}$'상(Fe4N)으로 두 개의 상으로 형성되는 것을 관찰할 수 있었다. 시험 결과를 바탕으로 S45C 소재의 탄소 함량에 따른 lehrer diagram을 열역학 적으로 계산하고 화합물층의 형성 기구에 대해 비교 분석하였다.

• 한국해양학회지
• /
• v.30 no.4
• /
• pp.302-319
• /
• 1995

The geochemical properties, sedimentation rates, foraminiferal distributions, and oxygen and carbon isotope records of sediment from Cores S-2 and S-19 were studied to investigate late Holocene paleoceanographic and paleoclimatic changes of the admiralty and Maxwell Bay, King George Island, Antarctica. Total organic carbon contents increased from the lower part to the upper part of Cores S-2 and S-19, whereas calcium carbonate contents decreased from the lower part to the upper part of Cores S-2 and s-19,whereas calcium carbonate contents decreased from the lower part to the upper part of Cores S-2 and S-19. Twenty-seven foraminiferal species were identified, and Globocassidurina biora was mostly a bundant in sediment samples. The sedimentation rates ranged from 24 cm/kyr to 237 cm/kyr based on /SUP 14/C-age dating of G. biora. The sedimentation rates increased rapidly in the upper part of the Cores. б/SUP 18/O values ranged from 0.3% to 6.2% and б/SUP 13/C values ranged from -3.0% to 0.0% with several fluctuations of the values. The lowest part of Core S-2, at 128 cmbsf in depth, had a /SUP 14/C-age of 3,100${\pm}$60 yr B.P. and the lowest part of Core S-19, at 230 cmbsf in depth, of 7,400${\pm}$ yr B.P. The results of geochemical and sedimentological analyses of the core sediments suggested five stages of paleoceanographic and paleoclimatic changes as follows: war,-cold stage of 7,500∼6,500 yr B.P., cold stage of 6,500∼3,600 yr B.P., cold-warm stage of 3,600∼2,770 yr B.P., warm stage of 2,770∼2,380 yr B.P. and cold-warm stage of 2,380∼2,100 yr B.P.

• Applied Chemistry for Engineering
• /
• v.20 no.4
• /
• pp.423-429
• /
• 2009

The purpose of this study is to investigate the optimal condition for the hydrogen-rich gas production and the CO removal by reforming of gliding arc plasma reforming system using biogas. The parametric screening studies were carried out according to changes of steam feed amount, catalyst bed temperature in water gas reactor and catalyst bed temperature, input air flow rate in preferential oxidation reactor. The standard condition is as follows. The steam/carbon ratio, catalyst bed temperature, total gas flow rate, input electric power and biogas composition rate ($CH_4$ : $CO_2$) were fixed 3, $700^{\circ}C$, 16 L/min, 2.4 kW and 6 : 4, respectively. The results are as follow, HTS optimum operating conditions were S/C ratio of 3 and reactor temperature of $500^{\circ}C$. LTS were S/C ratio of 2.9 and temperature of $300^{\circ}C$. Also, PROX I optimum conditions were input air flow rate of 300 mL/min and reactor temperature of $190^{\circ}C$. PROX II were 200 mL/min and $190^{\circ}C$ respectively. After having passed through each reactor, the results were as follows: 55% of $H_{2}$ yield, 0% of CO selectivity, 99% of $CH_4$ conversion rate, 27% of $CO_2$ conversion rate, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.493-496
• /
• 1999

Ni/3C-SiC 옴믹 접합에 대한 미세구조적-접합 특성과의 상관관계를 규명하였다. 3C-SiC 웨이퍼 위에 저저항 전면 옴믹 적합층을 형성하기 위하여 Ni(t=300$\AA$)을 thermal evaporator를 사용하여 증착하고, 50$0^{\circ}C$, 80$0^{\circ}C$, 103$0^{\circ}C$ 온도에서 30분간(Ar 분위기) 열처리 한 후, scratch test를 실행하여 Ni/3C-SiC의 접착력 특성을 조사하였다. 여러 다른 온도에 따른 Ni/3C-SiC 층의 표면과 계면의 미세구조는 X-ray scattering 법을 사용하였다. 50$0^{\circ}C$ 에서 열처리된 Ni/3C-SiC 층은 가장 낮은 계면 평활도와 가장 높은 표면 평활도를 나타내었다. Ni/3C-SiC 접착력 분석에서 500 $^{\circ}C$ 열처리된 시편의 측정된 임계하중 값은 As-deposited 시편(12 N~ 13 N)보다 훨씬 낮은 2 N~3 N 범위의 값을 보였으나, 열처리 온도가 증가함에 따라 다시 높아지는 경향을 보였다. 미세구조 특성에서는 열처리 온도가 500 $^{\circ}C$ 이상에서는 NiSi$_2$silicides의 domain size는 결정성의 향상에 따라 증가되었다. 결정성 향상이 3C-SiC와 silicides 사이의 격자상수의 낮은 불일치를 완화시키는데 기여 하였 다.

• Korean Journal of Materials Research
• /
• v.7 no.11
• /
• pp.1018-1023
• /
• 1997

본 연구에서는 3C-SiC의 ohmic 접합에 대하여 그 전기적 특성과 미세구조의 상관관계에 대하여 분석하였다. 표준사진식각 공정을 통하여 ohmic접합 금속으로서 Ni을 진공증착시켜 일련의 TLM패턴으로 열처리에 따르는 전류-전압 특성을 조사하였고 TEM, SEM, AES, EDS를 사용하여 Ni/SiC 계면에 대한 미세구조, 화학적 특성을 분석하였다. 열처리 온도와 시간을 통한 thermal budget이 증가함에 따라서 접촉저항이 감소되었으며 그 값은 $10^{-2}$-$10^{-4}$Ω$\textrm{cm}^2$의 범위에 속하였다. EDS와 AES를 통하여 7$50^{\circ}C$이상의 열처리 후 silicide(NiSi$_{2}$)의 주변에 carbon층이 형성되는 것을 확인하였으며, 열처리 온도가 증가함에 따라서 island형 silicide의 크기가 조밀해지며 SiC와의 접착성이 향상됨을 알 수 있었다. Ni/3C-SiC ohmic 접합의 전기적 특성은 계면에 생성되는 silicide와 carbon의 형성거동에 의하여 결정되는 것으로 믿어진다.

• Journal of Adhesion and Interface
• /
• v.22 no.3
• /
• pp.91-97
• /
• 2021

By introducing an organic interlayer on the Parylene C dielectric surface, the electrical device performances and the operating stabilities of organic field-effect transistors (OFETs) were improved. To achieve this goal, hexamethyldisilazane (HMDS) and octadecyltrichlorosilane (ODTS), as the organic interlayer materials, were used to control the surface energy of the Parylene C dielectrics. For the bare case used with the pristine Parylene C dielectrics, the field-effect mobility (μ_FET) and threshold voltage (V_th) of dinaphtho[2,3-b:2',3'-f ]thieno[3,2-b]- thiophene (DNTT) FET devices were measured at 0.12 cm²V^-1s^-1 and - 5.23 V, respectively. On the other hand, the OFET devices with HMDS- and ODTS-modified cases showed the improved μ_FET values of 0.32 and 0.34 cm²V^-1s^-1, respectively. More important point is that the μ_FET and V_th of the DNTT FET device with the ODTS-modified Parylene C dielectric presented the smallest changes during a repeated measurement of 1000 times, implying that it has the most stable operating stability. The results could be meaned that the organic interlayer, especially ODTS, effectively covers the Parylene C dielectric surface with alkyl chains and reduces the charge trapping at the interface region between active layer and dielectric, thereby improving the electrical operating stability.

• Geophysics and Geophysical Exploration
• /
• v.15 no.4
• /
• pp.155-162
• /
• 2012

The Thomsen-Haskell method was used to determine sensitivities of the Rayleigh-wave phase velocities and spectral amplitude of vertical ground motion to insertion of a single velocity-anomaly layer into overburden underlain by a basement. The reference model comprised a 9-m thick overburden with shear-wave velocity (${\nu}_s$ of 300 m/s above a half-space with ${\nu}_s$ = 1000 m/s. The inserted layer, with a velocity of 150, 225, 375, or 450 m/s and a thickness of 1, 2, or 3 m, was placed at depths increasing from the surface in increments of 1 m. Phase velocities were computed for frequencies of 4 to 30 Hz. For inserted layer models, we placed an anomalous layer with thickness of 1 ~ 3 m, shear-wave velocity of 150 ~ 450 m/s, and at depths of 0 ~ 8 m in the overburden. The frequency range of 8 ~ 20 Hz were the most sensitive to the difference of $C_R$ between the inserted and reference models (${\Delta}C_R$) for h = 1 m and the frequency range got wide as h increased. For all of the models, the spectral amplitudes of the fundamental mode exceeded those of the $1^{st}$-higher mode except at frequencies just above the low-frequency cutoff of the $1^{st}$-higher mode.