• 한국통신학회논문지
• /
• 제40권8호
• /
• pp.1606-1612
• /
• 2015

본 논문에서는 스마트폰에 장착 가능하고 휴대가 가능한 고효율 NDIR $CO_2$ 센서 모듈을 개발하였다. 저전력 회로 설계를 위하여 텅스텐램프 대신에 적외선 LED를 사용하였으며, 센서 모듈에 최적화된 광도파로를 설계 및 제작하였다. 스마트폰과 인터페이스가 가능한 회로를 통하여 스마트폰의 전원으로 센서 모듈이 구동되도록 설계하였다. $CO_2$ 농도, 온도 및 습도 등 측정된 센서의 데이터는 스마트폰 앱을 통하여 화면에 표시하였다. 측정 결과, 개발된 센서 모듈은 온도$-10^{\circ}C{\sim}50^{\circ}C$ 구간에서 0 ~ 3,000ppm 범위의 $CO_2$ 농도를 측정할 수 있었으며 측정 오차는 ${\pm}60ppm$이내였다.

• 대한환경공학회지
• /
• 제32권5호
• /
• pp.469-476
• /
• 2010

상수원수의 특성 변화와 갈수기 조류 발생으로 인한 원수 pH 상승 시기에 이산화탄소($CO_2$)를 주입하여 원수 pH를 조정함으로써 혼화·응집지의 응집 효율을 향상시켜 생산 정수 중의 잔류알루미늄, 탁도, 입자수 등의 농도를 낮추는 방법을 조사하고자 본 연구를 실시하였다. 원수 pH 8.0 이상이며 밤 낮의 pH 변화가 크지 않은 2월, 3월, 4월, 12월 중에 이산화탄소 주입 전 후의 정수 수질 변화를 고찰하였으며, 정수처리 공정수를 대상으로 정수 수질평가와 밀접한 관련이 있는 알루미늄, 탁도, 입자수, TOC, THMs, 2-MIB, geosmin 등의 농도 변화를 조사하였다. 조사결과, 혼화 응집지의 응집 효율 향상으로 입자수, 탁도, 알루미늄과 같은 입자성 물질과 무기물질은 감소하였으며 서울시 정수 목표수질값인 입자수 30개/mL 이하, 탁도 0.05 NTU 이하, 알루미늄 0.02 mg/L 이하의 양호한 정수 수질을 유지하기 위해서는 원수 pH 상승시기 이산화탄소를 주입하여 착수정원수 pH를 7.4 이하로 유지해야 하는 것으로 나타났다. 또한 THMs, CH, HAAs, HANs 등 소독부산물과 이취미 유발물질인 2-MIB, geosmin 농도는 원수 pH 변화와 무관함을 알 수 있었으며, 특히 이취미 유발물질인 2-MIB, geosmin는 pH 변화보다는 원수 중의 2-MIB, geosmin 농도가 정수 중의 농도 결정에 주요한 영향을 주는 것으로 나타났다.

• Ocean Systems Engineering
• /
• 제2권1호
• /
• pp.17-31
• /
• 2012

This study investigated the behavior of a non-isothermal $CO_2$ bubble formed through a leak process from a high-pressure source in a deep sea. Isenthalpic interpretation was employed to predict the state of the bubble just after the leak. Three modes of mass loss from the rising bubble were demonstrated: dissolution induced by mass transfer, condensation by heat transfer and phase separation by pressure decrease. A graphical interpretation of the last mode was provided in the pressure-enthalpy diagram. A threshold pressure (17.12 bar) was identified below which the last mode was no longer present. The second mode was as effective as the first for a bubble formed in deep water, leading to faster mass loss. To the contrary, only the first mode was active for a bubble formed in a shallow region. The third mode was insignificant for all cases.

• Advances in materials Research
• /
• 제4권2호
• /
• pp.63-76
• /
• 2015

The energy crisis involving depletion of fossil fuel resource is not the sole driving force for developing renewable energy technologies. Another driving force is the ever increasing concerns on the air quality of our planet, associated with the continuous and dramatic increase of the concentration of greenhouse gas (mainly carbon dioxide) emissions. The internal combustion engine is a major source of distributed $CO_2$ emissions caused by combustion of gasoline derived largely from fossil fuel. Another major source of $CO_2$ is the combustion of fossil fuels to produce electricity. New technologies for generating electricity from sources that do not emit $CO_2$, such as water, solar, wind, and nuclear, together with the advent of plug-in hybrid electric vehicles (PHEV) and even all-electric vehicles (EVs), offer the potential of alleviating our present problem. Therefore, the relevant technologies in $LiFePO_4$ as cathode material for Li-ion batteries suitable to the friendly environment are reviewed aim to provide the vital information about the growing field for energies to minimize the potential environmental risks.

• Journal of Welding and Joining
• /
• 제13권1호
• /
• pp.127-137
• /
• 1995

The possibility of new GMAW process using economic shielding gases including CO$_{2}$ gas was investigated on the effect of shielding gas on weldabilty. In the optimum welding condition using 600A power source, FCAW process showed low depositions rate, 114 g/min at 300A, but new GMAW using other mixed shielding gases exhibited high deposition rate, 208-224 g/min at 450A. TIME gas, Ar+CO$_{2}$ gas and Ar+CO$_{2}$+O$_{2}$ gas as a shielding gas were able to be used to the very high welding current(450A), moreover TIME gas and Ar+CO$_{2}$ gas showed the highest arc stability among shielding gases studied in this experiments. The weld penetration was performed by axial spray transfer mode of weld droplet. On the basis of workability, weldability and economic point of view, Ar mixture (80%Ar+20%CO$_{2}$) gas was recommended as a shielding gas for the development and application of new GMAW process. This shielding gas showed the low spatter, good weld quality, stable arc and low cost at the region of high welding current.

• 한국진공학회지
• /
• 제22권1호
• /
• pp.1-6
• /
• 2013

$600{\times}1,200mm$ 기판에 대면적 CIGS 광흡수층 증착을 위한 선형증발원 개발을 위해 다른 크기의 노즐과 일정한 노즐 간격을 가지는 선형증발원의 플럭스 밀도를 전산 모사하여 플럭스 균일도 ${\pm}5%$의 조건을 구하였다. 이를 바탕으로 제작된 선형증발원을 이용하여 Cu, In의 단일막 두께균일도를 확인하였고, CIGS 광흡수층을 동시증발법으로 증착하여 박막의 두께균일도 및 증착 조성의 균일도로 선형증발원을 평가하였다. XRF 조성 분석을 통해 구한 조성불균일도는 600 mm 폭에서 $$Cu{\leq_-}5%$$, $$In{\leq_-}7%$$, $$Ga{\leq_-}4%$$, $$Se{\leq_-}3%$$으로 균일한 조성비로 성막된 것을 확인하였고 SEM 분석을 통해 표면 결정립의 형상을 확인하였다. 또한 XRD측정을 통해 선형증발원 방향의 대면적 CIGS 광흡수층이 칼코피라이트 구조임을 확인하였다. 이를 통해서 개발된 하향 선형증발원이 CIGS 광흡수층 증착에 적합함을 확인하였다.

• 터널과지하공간
• /
• 제23권1호
• /
• pp.1-12
• /
• 2013

본 고에서는 $CO_2$ 지중저장과 연계한 원유회수증진 기술을 소개하였다. 원유회수증진을 목적으로 $CO_2$를 저류층 내에 주입하는 $CO_2$ EOR 기술은 장기적인 관점에서 $CO_2$를 지하 심부 암반에 저장하는 CCS 기술로 전환할 수 있다. CCS와 연계한 $CO_2$ EOR 기술은 EOR에 필요한 대규모 $CO_2$ 공급원을 확보할 수 있는 장점이 있으며 원유 회수율 증진에 따른 편익 발생으로 CCS를 위한 일련의 프로세스 중, 특히 포집 분야에 경제성을 부가할 수 있는 장점이 있다. 이러한 CCS와 연계한 $CO_2$ EOR 기술의 특징 및 시장 전망을 살펴보고 국외의 대표사례로 Weyburn $CO_2$ EOR 프로젝트를 소개하였다. 또한, 안정적이고 경제적인 $CO_2$ EOR 실시에 필요한 제반 기술 요소를 분석하고 $CO_2$ 주입중 및 주입후 장기운영과정에서의 미소진동 계측, $CO_2$의 최소혼화압력 및 최대주입압력의 사전설계 등의 암반공학적 쟁점들을 소개하였다.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.96-106
• /
• 2013

In this study, the effect of laser source($CO_2$ and Nd:YAG) on the microstructure and tensile properties of laser welded Al-Si coated boron steel(1.2mmt) was investigated with before and after hot-stamping. In case of as welds condition, fracture occurred in base metal unrelated to the laser source. It could be explained that tensile strength of fusion zone composed of martensite and bainite is higher than that of base metal that contains a lot of ferrite despite dilution of Al and Si from coating layer to fusion zone. In case of hot-stamping condition, the fracture occurred in fusion zone irrelevant to laser source and the tensile strength was lower than hot stamped base metal. In the $CO_2$ laser welds, $Fe_3$(Al,Si) formed near the bond line was transformed into ferrite during hot-stamping. Therefore tensile strength of bond line is lower than that of base metal and center of fusion zone and the fracture occurred in the bond line. On the other hand, in the Nd:YAG laser welds, the higher concentration of Al formed the ferrite in the fusion zone during hot-stamping treatment. Also, the thickness of centerline was thinner than that of base metal. Therefore, it is considered that fracture occurred in centerline of fusion zone due to effect of concentration stress, and it leaded to a lower tensile strength and elongation.

• 미생물학회지
• /
• 제21권1호
• /
• pp.27-35
• /
• 1983

The stoichiometry between the consumption of CO and $O_2$ and the production of $CO_2(2CO+O_2{\rightarrow}2CO_2)$) showed that Pseudomonas carboxydohydrogena grows as a typical aerobic CO oxidizer with CO. The optimal concentration of CO for growth was found to be 30% in gas mixture with air. The initial buffer concentration of the culture medium did not affect the growth of this bacterium. P. carboxydohydrogena is an obligate aerobe and dose not use nitrate as a terminal electron acceptor. The CO dehydrogenase is an inducible and soluble enzyme. The reaction rate and stability were maximal at pH7.5, and the Arrhenius plot revealed an activation energy of 37.7kJ/mol (9.0 Kcal/mol). The crude enzyme used methylene blue, thionin, and toluylene blue as electron acceptors for the oxidation of CO to $Co_2$ under anaerobic conditions. It was found that water must be the source of the second oxygen atom for CO oxidation.

• 상하수도학회지
• /
• 제24권3호
• /
• pp.319-332
• /
• 2010

In general, wastewater treatment systems consume high-energy consumption depending on operation characteristics of the facilities. Therefore, greenhouse gas(GHG) reduction activities that are application of digestion gas, induction of renewable energy etc. are conducted to reduce energy consumption and to increase energy independence ratio. In this study, GHG reduction in wastewater treatment system identified, searched application of Clean Development mechanism(CDM) approved methodology. If the methodologies apply to GHG reduction activities such as application of digestion gas, heat pump system using the wastewater as heat source, hydropower using the methodology determined CDM applicability, otherwise through several assumptions calculated expectable GHG reduction emissions and determined CDM applicability. As a result, the order of calculated GHG reduction emission showed that collected and energy generation of digestion gas is 66,775 $tCO_2$/yr, gas engine cogeneration system is 8,182 $tCO_2$/yr, heat pump system using the wastewater as a heat source is 72,715 $tCO_2$/yr, and hydropower is 561 $tCO_2$/yr. Consequently, the order of calculated Certified Emission Reductions(CERs) benefit showed that heat pump system using the wastewater, as a heat source is 1,381 million won/yr was estimated as the highest, followed by a collected and energy generation of digestion gas is 1,268 million won/yr.