• Clean Technology
• /
• v.13 no.2
• /
• pp.143-150
• /
• 2007

The objective of this study is to develop hydrocarbon-based cleaning agents by blending paraffins, glycol ethers and siloxanes in oder to effectively clean contaminants such as flux, solder and grease. And the effect of cleaning ability by wetting index, aniline points and solubility parameter of the formulated hydrocarbon-based cleaning agents were studied in this work. The formulated hydrocarbon-based cleaning agents were prepared on the base of physical properties of their individual components. Wetting indexes and aniline points of their were measured through experiments and solubility parameters of their were calculated based on the Hansen's equation. In this study, evaluation of cleaning ability by cleaning agents were carried out using contaminants such as flux, solder, and grease. The experimental results showed that the cleaning ability of the formulated cleaning agents was excellent in cleaning contaminants such as flux, solder and grease and that the influencing parameters on their cleaning efficiency were found to be different according to contaminant types. MC($20.3MPa^{1/2}$), DF-1 ($24.2MPa^{1/2}$) and DF-2($21.5MPa^{1/2}$) with similar solubility parameter as flux ($21.3MPa^{1/2}$) showed 100% cleaning efficiency within 3 minutes in flux cleaning. And CFC-113, MC and 1,1,1-TCE with low aniline point less than $-20^{\circ}C$ showed excellent cleaning efficiency in solder cleaning. DG-1($16.2\;MPa^{1/2}$) and DG-2($15.5\;MPa^{1/2}$) with similar solubility parameter as grease($15.0{\sim}17.0\;MPa^{1/2}$) showed relatively low cleaning efficiency of grease, but CFC-113 and MC with high wetting index and low aniline point showed good cleaning efficiency in grease cleaning. As a result of this study, the hydrocarbon-based cleaning agents alternative to regulated cleaning agents such as CFC-113, 1,1,1-TCE and MC were able to be developed through properly blending paraffins, glycol ethers and siloxanes for cleaning flux, solder and grease. And it can be shown that various influencing parameters of cleaning efficiency such as wetting index, aniline point, solubility parameter and etc. of the non-aqueous cleaning agent should be reviewed for prediction of their cleaning ability and can be applied to formulation of cleaning agents.

• Journal of the Korean Magnetic Resonance Society
• /
• v.6 no.1
• /
• pp.78-83
• /
• 2002

A new fluoroquinolone (DW-116) with a broad antibacterial spectrum was synthesized by introducing functional fluoropyridyl and methylpyrazine groups on N1, C7 position of quinolone moiety, respectively. $^{1}$H and $^{13}$ C NMR signal assignments and structure were completely elucidated by 2D-NMR methods. Physicochemical properties of products were also investigated. DW-116 is decomposed at 306.9$^{\circ}C$ and the decomposition starts at around 285$^{\circ}C$. The free base form is melt at 280.7$^{\circ}C$ and started to be decomposed immediately. DW-116 has two kinds of polymorphism which is important in drug action but these two plate and rod types have the same solubility in water. However the solubility is quite different in less or polar solvent. The plate type is more soluble in less polar solvent except in dichloromethane.

• Applied Chemistry for Engineering
• /
• v.23 no.2
• /
• pp.217-221
• /
• 2012

Blending films having enhanced water-resistance and barrier properties were prepared using the mixtures of poly(vinyl alcohol) (PVA) aqueous solution and poly(ethylene-co-acrylic acid) (EAA) dispersed in water. Thermal-mechanical properties, contact angles, water-vapor transmission rates (WVTR) and oxygen transmission rates $(O_2TR)$ were measured with the content of EAA of blending films, and their water-resistance was evaluated. The tensile strength of the films was found to be $9.16{\sim}11.75\;kg/mm^2$ which showed no significant difference compared with that of PVA, and the hardness increased with the content of EAA. The glass transition temperature and melting temperature of the blending films were slightly improved. The film prepared with PVA/EAA (= 90/10), of which the swelling and solubility were measured to be 109 and 0%, respectively, showed improved water-resistance. The WVTR and $O_2TR$ for the PET film (thickness $50\;{\mu}m$) coated with PVA/EAA (= 90/10) film (thickness $2.5\;{\mu}m$) were measured to be $9.1\;g/m^2/day$ and $2.0\;cc/m^2/day$, respectively.

• Korean Journal of Food Science and Technology
• /
• v.52 no.5
• /
• pp.516-523
• /
• 2020

Supercritical carbon dioxide (_SCO2) extraction was applied for the defatting of mealworm to prepare defatted powder (DP) and protein isolate (PI) and compare the process to press and hexane extraction, with respect to DP and PI physicochemical properties. _SCO2 DP was obtained by extracting 34.40% oil at 41.37 MPa, 40℃ for 180 min, and the product contained 71.66% crude protein, which is similar to that of hexane DP and higher than that of press DP. In using alkali protein extraction to prepare PI from DP, _SCO2 was as effective as hexane and better than press. _SCO2 produced brighter DP and PI than press, but not as much as hexane. Protein solubility was similar in all DP, with minimum values at pH 5. The highest water adsorption capacity was noticeable for _SCO2 PI, and _SCO2 DP showed an oil adsorption capacity comparable to that of hexane DP. _SCO2 DP and PI had better foaming capacity than press DP and PI and showed superior emulsion activity compared to others.

• Membrane Journal
• /
• v.25 no.3
• /
• pp.248-255
• /
• 2015

Aminated polyetherimide membrane synthesized in the laboratory according to amine ratio was used for measurement of gas permeability, diffusivity, and solubility about carbon dioxide, nitrogen, methane, oxygen, and sulfur dioxide with Time-lag method at room temperature. Generally, gas permeability is totally decreased because the more amination rate reacted to the main chain of amine groups, the more intermolecular space became narrow. However, gas permeability of sulfur dioxide was increased due to combination of sulfur dioxide and amine groups have acid and base properties respectively. Diffusivity and solubility of dry gas are totally decreased excluding sulfur dioxide as increasing amination rate. In case of sulfur dioxide, however, diffusivity as well as solubility was increased as increasing amination rate. Selectivity of carbon dioxide/nitrogen showed 60 when amination rate was 3. In case of humid gas, gas permeability of carbon dioxide was 70 barrer when relative humidity showed 100, and selectivity with nitrogen approximately showed 18.

• Carbon letters
• /
• v.2 no.3_4
• /
• pp.170-175
• /
• 2001

A petroleum-based isotropic pitch fiber spun by melt-blown method was oxidized in air flow at various conditions. The oxidized pitch fiber obtained was tested for its infusibility and its elemental composition during the process of stabilization. The structural changes were traced by using solvent solubility, FT-IR spectroscopy, and elemental analysis. The samples showed a gradual increase in weight with increasing the oxidization temperature. The weight gain of sample oxidized at $320^{\circ}C$ for 10 min was about 4.5%. The concentration of the pyridine and toluene soluble fraction decreased with an increase in stabilization temperatures. The oxygen uptaken in the stabilization process converted aliphatic side chains into the carbonyl groups. As stabilization proceeded, the more ether and carboxylic acid groups were formed through the oxidations of aldehyde and primary alcohol, and then the carboxylic acid was dehydrated to be aromatic anhydride.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.3
• /
• pp.307-314
• /
• 2003

The sonolytic decomposition of chlorofluorocarbon (CFC 113) and several alternative compounds, such as HCFC 225ca, HCFC 225cb, and HFC 134a, in.aqueous solutions was investigated. The CFC 113 with a high volatility and a low solubility in water was rapidly decomposed with increasing sonication time. The decomposition rates were influenced by the initial concentration of CFC 113, the reaction temperature, and the gas/liquid phase volume ratio but were independant of the pH of solution. The predominant pathway of the decomposition of CFC 113 by sonication was not the oxidation by OH radicals but the pyrolysis with high temperature and pressure inside of the cavitation bubble. The pyrolysis in the cavitation bubble resulted in an almost complete mineralization of CFC 113 with the high efficient formation of inorganic products (Cl$^{[-10]}$ , F$^{[-10]}$ , CO, $CO_2$). The addition of zinc powder on the decomposition of CFC 113 by sonication caused an acceleration of the decomposition. Also, HCFCs and HFC 134a were found to be readily decomposed by the pyrolysis induced from the sonication.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.192-193
• /
• 2006

In this paper, a co-axial type ozonizer varied with discharge gap was designed and manufactured for investigating (1) discharge characteristics with variation of output voltage power supply, flow rate and gap distance (2) ozone generation and solubility characteristics with variation of flow rate, gap distance and discharge power. Pure oxygen was used as process gas of the co-axial type ozonizer.

• Membrane Journal
• /
• v.33 no.3
• /
• pp.94-109
• /
• 2023

1,3-Dioxolane is an exciting material that has attracted widespread interest in the chemical, paint, and pharmaceutical industries as a solvent, electrolyte, and reagent because 1,3-dioxolane is not toxic, carcinogenic, explosive, auto-flammable, and multifunctional, and due to their excellent miscibility in most organic and aqueous solvent conditions. Recently, this material has received increasing attention as a CO₂-selective polymer precursor to separating CO₂ from flue gas and natural gas mixtures. Poly(1,3-dioxolane) (PDXL) possesses higher ether oxygen content than polyethylene oxide (PEO), which demonstrates superior membrane CO₂/N₂ separation properties owing to their polar ether oxygen groups exhibiting strong affinity toward CO₂. Thus, PDXL-based membranes displayed an outstanding CO₂ solubility selectivity over non-polar (N₂, H₂, and CH₄) gases. However, the polar groups of PDXL, like PEO, promote chain packing efficiency and cause polymer crystallization, thereby reducing its gas permeability, which should be improved. In this short review, we discuss the recent advancement and limitations of PDXL membranes in gas separation applications. To conclude, we provide future perspectives for inhibiting the limits of 1,3-dioxolane-based polymers in the CO₂ separation process.

• Journal of Powder Materials
• /
• v.12 no.5 s.52
• /
• pp.357-361
• /
• 2005

Fe-doped skutterudite $CoSb_3$ with a nominal composition of $Fe_{x}Co_{4-x}Sb_{12}(0\;{\le}\;x\;{\le}\;2.5)$ has been synthesized by mechanical alloying (MA) of elemental powders, followed by hot pressing. Phase transformations during mechanical alloying and hot pressing were systematically investigated using XRD. Single phase skutterudite was successfully produced by vacuum hot pressing using as-milled powders without subsequent annealing. However, second phase in the form of marcasite structure $FeSb_2$ was found to exist in case of $x\;{\ge}\;2$, suggesting the solubility limit of Fe with Co in this system. Thermoelectric properties as functions of temperature and Fe contents were evaluated for the hot pressed specimens. Fe substitution up to x=1.5 with Co in $Fe_{x}Co_{4-x}Sb_{12}$ appeared to increase thermoelectric figure of merit (ZT) and the maximum ZT was found to be 0.78 at 525K in this study.