• Journal of the Korea Organic Resources Recycling Association
• /
• v.26 no.4
• /
• pp.5-10
• /
• 2018

In this study, the effect of physico-chemical factors (e.g., pressure, electrolyte, and organic matter) in the gas hydrate deposit on CH4-CO2 replacement process was investigated experimentally. The higher initial pressure during gas injection led the higher reaction rate at the first time, but finally it did not. Electrolytes and organic matter have some effects on reforming process after dissociation of gas hydrate. It is expected that further research using real marine sediments with actual gas hydrate will enable the development of technologies applicable to the characteristics of domestic seabed geology. Ultimately, it is expected that it will be possible to recover and utilize methane as an organic resource through application of domestic gas hydrate deposit in the Ulleung Basin, East Sea.

• Applied Chemistry for Engineering
• /
• v.23 no.1
• /
• pp.1-7
• /
• 2012

In this article, I will introduce recent developments of environmental-friendly materials fabricated using atomic layer deposition (ALD). Advantages of ALD include fine control of the thin film thickness and formation of a homogeneous thin fim on complex-structured three-dimensional substrates. Such advantages of ALD can be exploited for fabricating environmental-friendly materials. Porous membranes such as anodic aluminum oxide (AAO) can be used as a substrate for $TiO_2$ coating with a thickness of about 10 nm, and the $TiO_2$-coated AAO can be used as filter of volatile organic compound such as toluene. The unique structural property of AAO in combination with a high adsorption capacity of amorphous $TiO_2$ can be exploited in this case. $TiO_2$ can be also deposited on nanodiamonds and Ni powder, which can be used as photocatalyst for degradation of toluene, and $CO_2$ reforming of methane catalyst, respectively. One can produce structures, in which the substrates are only partially covered by $TiO_2$ domains, and these structures turns out to be catalytically more active than bare substrates, or complete core-shell structures. We show that the ALD can be widely used not only in the semiconductor industry, but also environmental science.

• Membrane Journal
• /
• v.32 no.4
• /
• pp.218-226
• /
• 2022

Hydrogen, a carrier of large-capacity chemical and clean energy, is an important industrial gas widely used in the petrochemical industry and fuel cells. In particular, hydrogen is mainly produced from fossil fuels through steam reforming and gasification, and carbon dioxide is generated as a by-product. Therefore, in order to obtain high-purity hydrogen, carbon dioxide should be removed. This review focused on free-standing polymeric membranes and mixed-matrix membranes (MMMs) that separate hydrogen from carbon dioxide reported in units of Barrer [1 Barrer = 10^-10 cm³ (STP) × cm / (cm² × s × cmHg)]. By analyzing various recently reported papers, the structure, morphology, interaction, and preparation method of the membranes are discussed, and the structure-property relationship is understood to help find better membrane materials in the future. Robeson's upper bound limits for hydrogen/carbon dioxide separation were presented through reviewing the performance and characteristics of various separation membranes, and various MMMs that improve separation properties using technologies such as crosslinking, blending and heat treatment were discussed.

• Korean Chemical Engineering Research
• /
• v.61 no.2
• /
• pp.296-301
• /
• 2023

Solid oxide fuel cell has received more attention recently due to the fuel flexibility via internal reforming. Commonly used Ni/YSZ anode, however, can be easily deactivated by carbon coking in hydrocarbon fuels. The carbon deposition problem can minimize by developing alternative perovskite anode. This study is focused on improving conductivity and catalytic activity of the perovskite anode by introducing rGO (reduced graphene oxide). Sr_0.92Y_0.08TiO₃(SYT) anode with perovskite structure was synthesized with 1wt% of rGO. The presence of rGO during anode fabricating process and cell operation is confirmed through XPS and Raman analysis. The maximum power density of rGO/SYT anode improved to 3 times in H₂ and 6 times in CH₄ comparing to that of SYT anode due to the high electrical conductivity and good catalytic activity for CH₄.

• Korean Journal of Materials Research
• /
• v.21 no.1
• /
• pp.1-7
• /
• 2011

Methods of producing hydrogen include steam reforming, electrochemical decomposition of water, and the SI process. Among these methods, the Sulfur iodine process is one of the most promising processes for hydrogen production. The thermochemical sulfur-iodine (SI) process uses heat from a high-temperature-gas nuclear reactor to produce $H_2$ gas; this process is known for its production of clean energy as it does not emit $CO_2$ from water. But the SI-process takes place in an extremely corrosive environment for the materials. To endure SI environments, the materials for the SI environment will have to have strong corrosion resistance. This work studies the corrosion resistances of the Fe-Si, Ni-Ti and Ni Alloys, which are tested in SI-process environments. Among the SI-process environments, the conditions of boiling sulfuric acid and decomposed sulfuric acid are selected in this study. Before testing in boiling sulfuric acid environments, the specimens of Fe-4.5Si, Fe-6Si, Ni-4.5Si, Ni-Ti-Si-Nb and Ni-Ti-Si-Nb-B are previously given heat treatment at $1000^{\circ}C$ for 48 hrs. The reason for this heat treatment is that those specimens have a passive film on the surface. The specimens are immersed for 3~14 days in 98wt% boiling sulfuric acid. Corrosion rates are measured by using the weight change after immersion. The corrosion rates of the Fe-6Si and Ni-Ti-Si-Nb-B are found to decrease as the time passes. The corrosion rates of Fe-6si and Ni-Ti-Si-Nb-B are measured at 0.056 mm/yr and 0.16 mm/yr, respectively. Hastelloy-X, Alloy 617, Alloy 800H and Haynes 230 are tested in the decomposed sulfuric acid for one day. Alloy 800H was found to show the best corrosion resistance among the materials. The corrosion rate of Alloy 800H is measured at -0.35 mm/yr. In these results, the corrosion resistance of materials depends on the stability of the oxide film formed on the surface. After testing in boiling sulfuric acid and in decomposed sulfuric acid environments, the surfaces and compositions of specimens are analyzed by SEM and EDX.

• Journal of Wetlands Research
• /
• v.19 no.1
• /
• pp.1-15
• /
• 2017

Wetland function assessment is not only a basic step to understand wetland ecosystems in detail but also an important process as a base of the term, ecosystem service to recognize wetland ecosystems as valuable and useful resources and goods for human being. WET (wetland evaluation technique), EMAP (environmental monitoring assessment program)-wetlands, and HGM (hydrogeomorphic method) were developed as pioneer wetland function assessments in U.S. at the end of $20^{th}$-century. RAMs (rapid assessment methods) became a major function assessment tool which is relatively simpler and easier assessment tool at the beginning of $21^{th}$-century. After that, the hierarchy of three levels of assessment (landscape assessment, rapid assessment, and intensive assesment) has been prepared and strategically utilized according to the objectives and purposes of function assessments. In South Korea, RAM and HGM were used to assess wetland functions with reforming a couple of items and contents at 2001. And, modified and reformed function assessments have been developed to complement and improve upon the existing RAMs and HGMs. Via the trend analysis on wetland function assessments, some needs which require supplements in terms of function assessment are pointed out: 1) wetland function assessments using useful indicators such as birds are needed with considering our environmental characteristics. 2) optimized wetland function assessments for coastal wetlands are also needed. 3) the network construction and further expansion to lead communications and co-operations between researchers and policy makers is needed in the field of wetland function assessment.