• 한국수소및신에너지학회논문집
• /
• 제15권4호
• /
• pp.301-308
• /
• 2004

The methane reforming with $CO_2$ and steam for manufacture of synthesis gas over $Ni/ZrO_2$ catalyst was investigated. Mixed reforming carried out $CO_2$ dry reforming with $O_2$ and steam for development of DME process in pilot plant. To improve a catalyst deactivation by coke formation, the mixed reforming added carbon dioxide and steam as a oxidizer of the methane reforming was suggested. The result of experiments over commercial catalyst in $CO_2$ dry reforming has shown that the catalyst activity decrease rapidly after 20 hours. In case of $NiO-MgO/Al_2O_3$ catalyst, the deactivation of 20 percent after 30 hours was occurred. The activity of Ni/C catalyst still was not decreased dramatically after 100 hours. The effect of $H_2$ reforming with steam over $Ni/CO_2$ catalyst obtained the optimal conversion of methane and carbon dioxide, and could be produced synthesis gas at ratio of $H_2/CO$ under 1.5.

• 한국연소학회지
• /
• 제13권4호
• /
• pp.47-53
• /
• 2008

The reaction mechanism of methane dry reforming has been investigated using an arc-jet reactor. The effects of input power, $CO_2/CH_4$ and added $O_2$ were investigated by product analysis, including CO, $H_2$, $C_{2}H_{Y}$ and $C_{3}H_{Y}$ as well as $CH_4$ and $CO_2$. In the process, input electrical power activated the reactions between $CH_4$ and $CO_2$ significantly. The increased feed ratio of the $CO_2$ to $CH_4$ in the dry reforming does not affect to the $CH_4$ conversion. but we could observe increase in CO selectivity together with decreasing $H_2$ generation. Added oxygen can also increase not only CO selectivity but also $CH_4$ conversion. However, hydrogen selectivity was decreased significantly due to a increased $H_{2}O$ formation.

• Korean Chemical Engineering Research
• /
• 제56권2호
• /
• pp.176-185
• /
• 2018

지구 온난화가 가속화됨에 따라 온실가스 감축이 보다 중요해졌다. 이산화탄소 건식 개질은 온실가스인 $CO_2$와 $CH_4$를 활용하여 부가가치가 높은 물질인 CO와 $H_2$를 얻을 수 있는 유망한 온실가스 감축 기술이다. 그러나 이 반응이 일어나는 반응기의 운전 중에 심각한 코킹 문제가 발생할 수 있다. 이산화탄소 개질반응은 매우 강한 흡열반응이기 때문에 반응기 입구 근처에서 반응 온도가 많이 떨어지면서 코크 생성을 야기시킨다. 이러한 문제를 해결하기 위해서는 코크 생성이 잘 일어나지 않는 온도영역에서 반응이 일어나도록 하는 것이 중요하다. 본 연구에서는 새로운 촉매 배열 방법을 이용하여 반응기 전 구간이 코크 생성이 잘 일어나지 않는 온도 영역 내에서 유지되도록 하는 설계 방법을 제안하였다. 이 설계 방법은 연료 유량, 촉매 밀도, 구간 별 출구 온도를 최적화 변수로 하여 주어진 전환율에 대하여 반응기 길이를 최소화 할 수 있는 최적화 문제를 풀도록 하여 반응기를 최적화한다.

• International Journal of Advanced Culture Technology
• /
• 제3권2호
• /
• pp.110-117
• /
• 2015

10 wt% (Ni-Co) catalysts with different Ni and Co content : 10%Ni, 9%Ni1%Co, 7%Ni3%Co, 5%Ni5%Co, 3%Ni7%Co, and 10%Co; were prepared using sol-gel method followed by incipient wetness impregnation method. To investigate the catalytic activity including the stability, dry methane reforming were demonstrated over the pelletized catalysts at $620^{\circ}C$ under atmospheric pressure in a $CH_4:CO_2:N_2$ feedstock for 360 min. The results showed that bimetallic catalysts with the Co content equal to or greater than 3% were more stable than monometallic catalysts (10%Ni and 10%Co). The temperature programmed hydrogenation interpreted that the additional of Co into Ni catalyst improved the carbon resistance from methane cracking. Promoted this type of bimetallic catalyst using 1wt% K (trimetallic catalyst) prevented the carbon formation on the catalyst. The temperature programmed desorption of $CO_2$ indicated that this trimetallic catalyst has a greater number of strong basic sites. Moreover, the appearance of K lowered the number of weak basic sites and decreased the conversion of methane by 12 %.

• Bulletin of the Korean Chemical Society
• /
• 제26권12호
• /
• pp.2017-2020
• /
• 2005

The supported bimetallic Co-containing catalysts promoted by the different amount of noble metal (Pd) have been studied in the dry reforming of methane. The activity, selectivity, stability and resistance to the carbon deposition of Co-Pd/$Al_2O_3$ catalysts depend on both the catalyst composition and process conditions. It has been observed that the Co-Pd/$Al_2O_3$ catalysts produce the various oxygenates from $CO_2$ + $CH_4$ at moderate pressures.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.55-58
• /
• 2007

To check the feasibility of SMART (Steam Methane Advanced Reforming Technology)system, an experimental investigation was conducted. A fluidized bed reactor of diameter 0.052 m was operated cyclically up to the $10^{th}$ cycle, alternating between reforming and regeneration conditions. FCR-4 catalyst was used as the reforming catalyst and calcined limestone (domestic, from Danyang) was used as the $CO_2$ absorbent. Hydrogen concentration of 98.2% on a dry basis was reached at $650^{\circ}C$ for the first cycle. This value is much higher than $H_2$ concentration of 73.6% in the reformer of conventional SMR (steam methane reforming) system. However, the hydrogen concentration decreased because the $CO_2$ capture capacity decreased as the number of cycles increased.

• 청정기술
• /
• 제23권3호
• /
• pp.314-324
• /
• 2017

To verify the viability of Co, Ru and Zr-based catalyst for $CO_2$ (dry) reforming reaction, catalysts were fabricated using cordierite, silicon carbide and rota monolithic substrates, and they were compared with the conventional $Co-Ru-Zr/SiO_2$ catalyst in terms of performance and durability. Cordierite monolith was showed high activity with the least amount of active component. In addition, when Cordierite monolith was coated with Co-Ru-Zr in various ways, most excellent performance was showed at a precursor solution coating method. In particular, when 0.9 wt% Co-Ru-Zr/Cordierite was used for reaction, it was observed that 95% $CO_2$ conversion was maintained for 300 h at $900^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• 제23권8호
• /
• pp.1149-1153
• /
• 2002

CH4/CO2 dry reforming was carried out to make syn gas on the Ni/Al2O3 catalysts calcined at different temperatures. The Ni/Al2O3 (850 $^{\circ}C)$ catalyst gave good activity and stability w hereas the Ni/Al2O3 $(450^{\circ}C)$ catalyst showed lower activity and stability. The NiO/Al2O3 catalyst calcined at $850^{\circ}C$ for 16 h (Ni/Al2O3 $(850^{\circ}C))$ formed the spinel structure of nickel aluminate, which was confirmed by TPR. The carbon formation rate on the Ni/Al2O3 $(850^{\circ}C)$ catalyst was very low till 20 h, and then steeply increased with reaction time without decreasing the activity for CH4 reforming. The Ni/Al2O3 $(450^{\circ}C)$ catalyst showed high carbon formation rate at the initial reaction time and then, the rate nearly stopped with continuous decreasing the activity for CH4 reforming. Even though the amount of carbon deposition on the Ni/Al2O3 $(850^{\circ}C)$ catalyst was higher than that on the Ni/Al2O3 $(450^{\circ}C)$ catalyst, the activity for CH4ing was also high, which could be attributed to the different type of the carbon formed on the catalyst surface.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.71.2-71.2
• /
• 2013

천연가스를 화학적 전환에 의해 부가가치를 높이기 위해서는 리포밍에 의해 합성가스(CO/H2)를 경유하는 간접전환경로가 현재로서는 가장 현실적인 방법이라 할 수 있다. 천연가스를 이용한 합성가스 제조기술은 수증기개질법(SRM), 이산화탄소 개질법(CDR, dry reforming), 부분산화법, 촉매 부분 산화법, 자열개질법 등으로 구분되며, 최근에는 각각의 제조방법의 장점을 고려하여 혼합개질법 또는 일련의 리포머 조합 방법이 개발되고 있다. CDR은 촉매 하에서 메탄과 이산화탄소의 직접접촉에 의해 반응이 일어나며, 수소와 일산화탄소의 비가 같은 합성가스가 제조된다. SRM에 비하여 고온에서 반응이 일어나고 전환율이 더 낮으므로 에너지 소비가 상대적으로 높다. 하지만, SRM과 함께 사용하면 합성가스 비율을 F-T합성이나 메탄올 합성에 적절한 비율로 조절이 가능한 장점이 있으며, 온실가스를 저감시킬 수 있는 전환기술로도 각광받고 있다. 본 발표에서는 최근의 CDR을 이용한 가스로부터 합성석유(GTL)와 메탄올을 고효율로 생산하는 기술 개발 동향에 대해서 소개하고자 한다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2005년도 제31회 KOSCO SYMPOSIUM 논문집
• /
• pp.64-68
• /
• 2005

Methane reforming processes to obtain hydrogen were investigated experimentally by using atmospheric plasma source. Among possible reforming processes, such as a $CO_2$ reforming(dry reforming), a partial oxidation (POx), a steam reforming(SR), and a steam reforming with oxygen(SRO or auto-thermal reforming), partial oxidation and the steam reforming with oxygen were considered. We choose a rotating arc plasma as an atmospheric plasma source, since it shows the best performances in our preliminary tests in terms of a methane conversion, a hydrogen production, and a power consumption. Then, the effects of a feeding flow-rate, an electrical power input to a plasma reaction, an $O_2/C$ ratio and a steam to carbon ratio in the case of SRO on the reforming characteristics were observed systematically. As results, at a certain condition almost 100% of methane conversion was obtained and we could achieve the same hydrogen production rate by consuming a half of electrical power which was used by the best results for other researchers.