• 한국지반공학회논문집
• /
• 제34권11호
• /
• pp.33-41
• /
• 2018

지반의 내부침식은 유체 흐름에 의하여 입자골격에 부착된 세립토가 이탈하는 현상이며, 지속적인 세립토의 유동은 지반구조물의 수리-역학적 특성을 약화시킨다. 본 논문은 세립토의 유동에 관한 지배방정식을 정립하고 수치해석 기법을 제안하였다. 공극내의 세립토는 액상의 세립토($c_e$), 조립토에 부착된 입자(${\sigma}_a$) 그리고 조립토골격에 폐색된 세립토(${\sigma}_s$)로 구분하여 상관계를 제시하였다. 이를 바탕으로 세립토의 유동과 공극수의 흐름에 대한 수리학적 지배방정식들과 유한요소 수식화를 제시하였다. 세립토의 이탈, 부착 그리고 공극막힘에 대한 구성 모델들을 제시하였으며, 실내 1차원 침식실험으로부터 모델변수를 도출하는 방법을 제안하였다. 그리고 세립토의 공극 막힘 현상에 의한 지반의 투수계수 변화에 대한 추정식을 제안하였다. 기존의 침식실험 결과에 대한 수치해석을 통하여 개발된 해석기법과 세립토 유동 모델의 적정성을 검증하였다.

• 대한금속재료학회지
• /
• 제49권2호
• /
• pp.93-103
• /
• 2011

Precipitation behavior of high-nitrogen duplex Fe-24Cr-7Mn-4Ni-4Mo-0.43N stainless steel aged at $850^{\circ}C$ was investigated using scanning transmission electron microscopy. Based on the analyses of selected area diffraction patterns, four kinds of precipitates (intermetallic sigma (${\sigma}$) and chi (${\chi}$), $Cr_2N$ and secondary austenite) were identified. At the ferrite/austenite phase boundary, the ${\sigma}$ phase and secondary austenite were formed via ${\alpha}{\rightarrow}{\gamma}+{\sigma}$ eutectoid reaction. The precipitation of $Cr_2N$ occurred at the austenite grain boundary as well as the interior of the ferrite. The intermetallic ${\chi}$ phase also formed within the ferrite and showed a cube-cube orientation relationship with the ferrite. Further aging produced a lamellar structure composed of $Cr_2N$ and austenite along the ferrite/austenite boundary and enhanced the precipitation of the ${\chi}$ phase. The crystallographic features of the precipitates were also examined in terms of the orientation relationship with the austenite or ferrite matrix.

• 한국안광학회지
• /
• 제6권2호
• /
• pp.11-16
• /
• 2001

렌즈에 가한 응력을 측정하기 위한 편광기는 1/4 파장판-편광판으로 구성하였고, 각 단계별 광파의 $E_1$, $E_2$의 성분을 분석하였다. 주 응력차 ${\sigma}_1-{\sigma}_2$는 무늬 차수(N)가 시료 각 점에서 분석되고, 시료의 광축은 주 응력 방향과 일치하는 것으로부터 2 차원 모델을 결정할 수 있다. 광파에 작용하는 복굴절성과 위상지연은 주 응력차 (${\sigma}_1-{\sigma}_2$)에 비례하고, 최종 광파의 세기는 $sin^2({\Delta}/2)$에 비례하고, ${\Delta}/2=n^{\pi}$ (n=0, 1, 2, ...)일 때 소멸 무늬인 흡광이 일어난다. 실험적 결과로는 렌즈의 외부 응력의 크기에 따라 흡광 band가 이동한다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권3호
• /
• pp.313-321
• /
• 2014

A low-power low-cost polar transmitter for EDGE is designed in $0.18{\mu}m$ CMOS. A differential delta-sigma modulator (DSM) tunes a three-terminal voltage-controlled oscillator (VCO) to perform RF phase modulation, where the VCO tuning curve is digitally pre-compensated for high linearity and the carrier frequency is calibrated by a dual-mode low-power frequency-locked loop (FLL). A digital intermediate-frequency (IF) pulse-width5 modulator (PWM) drives a complementary power-switch followed by an LC filter to achieve envelope modulation with high efficiency. The proposed transmitter with 9mW power dissipation relaxes the time alignment between the phase and envelope modulations, and achieves an error vector magnitude (EVM) of 4% and phase noise of -123dBc/Hz at 400kHz offset frequency.

• 품질경영학회지
• /
• 제36권4호
• /
• pp.37-46
• /
• 2008

There are big differences in six sigma projects between manufacturing processes and transactional/service processes. This paper analyzed the differences between the two areas by examining 18 six sigma case studies in Korean companies. To characterize six sigma case studies, step-by-step questions and check criteria were developed based on 12 step DMAIC methodology. On the basis of those characterized data, the differences between two areas were analyzed. Significant differences were found in the number of CTQs, validation of measurement systems, methods to determine improvement objectives, the methods to elicit improvement plans and types of control systems. The most significant difference was that statistical tools were widely used in manufacturing processes, but qualitative tools were used in transactional/service processes during improvement phase.

• 산업공학
• /
• 제16권spc호
• /
• pp.7-13
• /
• 2003

This paper is concerned with a six sigma green belt training program. Comparative studies of existing training programs for three major companies (Samsung Electronics Company, Hyundai Motor Company, and LG Chemical Ltd.) and two consulting firms (Korean Standards Association and Korea Management Association) are made. Based on the comparative studies, a new green belt training program is proposed. The main focus of this program is on manufacturing, specially on cost and waste reductions, yield improvement, and operations with opportunity to improve capacity without major capital expenditure. The green belts take up to 4 or 5 days of intensive, highly quantitative training, roughly corresponding to the five macro phases of the six sigma methodology: define, measure, analyze, improve, and control. The six sigma tool sets for each phase are also specified.

• 동력기계공학회지
• /
• 제18권2호
• /
• pp.70-76
• /
• 2014

A specimen of weld metal was prepared by GTA welding with weld wire of super duplex stainless steel. Aging treatment was conducted for the sample at the temperature range of 700 to $900^{\circ}C$ for 5 to 300 minutes. The effect of aging temperature and time to pitting corrosion of weld metal has been investigated and the results were derived as follows. The volume fraction of ${\sigma}$ phase tends to increase with an increase of aging temperature and time. Pitting potential Ep representing pitting corrosion was found to tend to decrease with an increase of aging time at 700 to $900^{\circ}C$. And most of the pits formed near the ${\sigma}$-phase in the ferrite and seemed to propagated to austenite.

• ETRI Journal
• /
• 제36권6호
• /
• pp.924-930
• /
• 2014

This paper presents a $0.13{\mu}m$ CMOS 3-level envelope delta-sigma modulation (EDSM) RF signal generator, which synthesizes a 2.6 GHz-centered fully symmetrical 3-level EDSM signal for high-efficiency power amplifier architectures. It consists of an I-Q phase modulator, a Class B wideband buffer, an up-conversion mixer, a D2S, and a Class AB wideband drive amplifier. To preserve fast phase transition in the 3-state envelope level, the wideband buffer has an RLC load and the driver amplifier uses a second-order BPF as its load to provide enough bandwidth. To achieve an accurate 3-state envelope level in the up-mixer output, the LO bias level is optimized. The I-Q phase modulator adopts a modified quadrature passive mixer topology and mitigates the I-Q crosstalk problem using a 50% duty cycle in LO clocks. The fabricated chip provides an average output power of -1.5 dBm and an error vector magnitude (EVM) of 3.89% for 3GPP LTE 64 QAM input signals with a channel bandwidth of 10/20 MHz, as well as consuming 60 mW for both channels from a 1.2 V/2.5 V supply voltage.

• Nuclear Engineering and Technology
• /
• 제38권5호
• /
• pp.405-410
• /
• 2006

Microstructural features and their related mechanical property changes in the 309L cladding and the heat affected zone (HAZ) of SA508 cl.3 steel were investigated through the use of TEM, tensile and small punch (SP) tests. The specimens were irradiated at 563 K up to the neutron fluences of $5.79{\times}10^{19}n/cm^2$ (>1MeV). The microstructure of the clad was mainly composed of a fcc ${\gamma}-phase$, a low percentage of bcc ${\delta}-ferrite$, and a brittle ${\sigma}-phase$. Along the weld fusion line there formed a heavy carbide precipitation with a width of $20{\sim}40{\mu}m$, showing preferential cracking during plastic deformation. The yield stress and ductile-to-brittle transition temperature (DBTT) of the irradiated clads increased. The origin of the hardening and the shift of the DBTT are discussed in terms of the irradiation-produced defect clusters of a fine size and brittle ${\sigma}-phase$.

• 오토저널
• /
• 제10권2호
• /
• pp.46-53
• /
• 1988

Effect of Notch Shape and Hardness Ratio on Characteristics of Impact Fracture in Dual Phase Steels. In this study, it is investigated the effect of notch shape and hardness ratio on the characteristics of impact fracture in dual phase steels. The impact test was carried out at the temperature range from -40.deg. C to room temperature with Instrumented Charpy Impact Tester. The main results obtained are as follows; 1, The maximum impact bending strength (.sigma.$_{max}$) increases with the tensile strength. Also, the impact energy depends on .sigma.$_{max}$. 2, In room temperature, the impact energy depends on crack-initiation energy (E$_{i}$) in case of the high hardness ratio (R=3.4), whereas depends on crack-propagation energy (E$_{p}$) in case of the low hardness ratio (R=1.8) and the dependence of crack-initiation energy of the impact characteristics decreases with increasing test temperature. These phenomena are result from the difficulty of cleavage facet formation.ion.ion.