• Nuclear Engineering and Technology
• /
• v.43 no.6
• /
• pp.583-592
• /
• 2011

The radiological characteristics for waste classification were assessed for neutron-activated decommissioning wastes from a CANDU reactor. The MCNP/ORIGEN2 code system was used for the source term analysis. The neutron flux and activation cross-section library for each structural component generated by MCNP simulation were used in the radionuclide buildup calculation in ORIGEN2. The specific activities of the relevant radionuclides in the activated metal waste were compared with the specified limits of the specific activities listed in the Korean standard and 10 CFR 61. The time-average full-core model of Wolsong Unit 1 was used as the neutron source for activation of in-core and ex-core structural components. The approximated levels of the neutron flux and cross-section, irradiated fuel composition, and a geometry simplification revealing good reliability in a previous study were used in the source term calculation as well. The results revealed the radioactivity, decay heat, hazard index, mass, and solid volume for the activated decommissioning waste to be $1.04{\times}10^{16}$ Bq, $2.09{\times}10^3$ W, $5.31{\times}10^{14}\;m^3$-water, $4.69{\times}10^5$ kg, and $7.38{\times}10^1\;m^3$, respectively. According to both Korean and US standards, the activated waste of the pressure tubes, calandria tubes, reactivity devices, and reactivity device supporters was greater than Class C, which should be disposed of in a deep geological disposal repository, whereas the side structural components were classified as low- and intermediate-level waste, which can be disposed of in a land disposal repository. Finally, this study confirmed that, regardless of the cooling time of the waste, 15% of the decommissioning waste cannot be disposed of in a land disposal repository. It is expected that the source terms and waste classification evaluated through this study can be widely used to establish a decommissioning/disposal strategy and fuel cycle analysis for CANDU reactors.

• Journal of The Korean Astronomical Society
• /
• v.37 no.5
• /
• pp.337-342
• /
• 2004

The presence of magnetic fields in the intracluster medium in clusters of galaxies has been revealed through several different observational techniques. These fields may be dynamically important in clusters as they will provide additional pressure support to the intracluster medium as well as inhibit transport mechanisms such as thermal conduction. Here, we review the current observational state of Faraday rotation measure studies of the cluster fields. The fields are generally found to be a few to 10 $\mu$G in non-cooling core clusters and ordered on scales of 10 - 20 kpc. Studies of sources at large impact parameters show that the magnetic fields extend from cluster cores to radii of at least 500 kpc. In central regions of cooling core systems the field strengths are often somewhat higher (10 - 40 $\mu$G) and appear to be ordered on smaller scales of a few to 10 kpc. We also review some of the recent work on interpreting Faraday rotation measure observations through theory and numerical simulations. These techniques allow us to build up a much more detailed view of the strength and topology of the fields.

• Progress in Superconductivity and Cryogenics
• /
• v.15 no.3
• /
• pp.29-34
• /
• 2013

This paper introduces design processes of 10 MW class superconducting generator for wind Turbine. Superconducting generator can produce 5 times stronger magnetic field than permanent magnet at least, which enables large scale wind turbine to function as a lighter, smaller and more highly efficient system. These processes are targeted for higher efficiency and shorter high temperature superconductor (HTS) wires to fabricate 10 MW class superconducting generator. Three different approaches will be described in these design processes. First design process focuses on the number of rotor poles. Secondly, 270 and 360 A operating current of superconducting field coil can be adapted as a design parameter in this process. Lastly, 3 and 6 kV line to line voltage of stator coil will be used to design 10 MW class superconducting generator.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.10
• /
• pp.922-929
• /
• 2004

In this paper, we develop control hardware such as an FPGA based general purposed intelligent controller with a DSP board to solve nonlinear system control problems. PID control algorithms are implemented in an FPGA and neural network control algorithms are implemented in a BSP board. An FPGA was programmed with VHDL to achieve high performance and flexibility. The additional hardware such as an encoder counter and a PWM generator can be implemented in a single FPGA device. As a result, the noise and power dissipation problems can be minimized and the cost effectiveness can be achieved. To show the performance of the developed controller, it was tested fur nonlinear systems such as a robot hand and an inverted pendulum.

• Plant Resources
• /
• v.6 no.3
• /
• pp.221-226
• /
• 2003

To improve industrial scale extraction method for extraction of icariin from Epimedium koreanum Nakai, the yields under different extracting conditions such as solvent, temperature, duration and solvent to plant material weight ratio were compared. Regarding extracting solution, highest extracts and icariin yield could be achieved when 10% EtOH was used. In case of plant material to extracting solvent ratio, no significant differences could be observed from 1/10 to 1/50, indicating 1/10 was the most efficient. Extracting temperature significantly affected extracts and icariin yields in that 9$0^{\circ}C$ increased the collected extracts and icariin contents up to 29.6% and 0.76%, respectively, compared to 27.2%, 0.33% at 7$0^{\circ}C$. The yield of extracts was less dependent upon extracting temperature compared to icariin yield. Regarding extraction time, 4 hr and 6 hr resulted in high extracts and icariin yield, respectively. We found extracting Epimedium koreanum Nakai in 10 times volume of 10% EtOH for 4 and 6 hr at 9$0^{\circ}C$ seem to be relatively efficient methods for extracts and icariin, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.6 no.1
• /
• pp.11-15
• /
• 1985

Electrical conductivites of polycrystalline yttrium sesquioxides containing 1.6 and 3.2 mol % of holmium sesquioxdes have been measured from 650 to $1050^{\circ}C$ under oxygen partial pressures of $1{\times}10^{-5}$ to $2{\times}10^{-1}$ atm. Plots of log conductivity vs. 1/T at constant oxygen partial pressures are found to be linear away from the two inflection points. The low- and high-temperature dependences of conductivity show different defect structures of yttrium sesquioxide. The plots of log conductivity vs. log $PO_2$ are found to be linear at $PO_{2'}$s of $10^{-5}$ to $10^{-1} atm. The electrical conductivity dependences on $PO_2$ are found to be $1}5.3$ at $950-1050^{\circ}C$, $\frac{6}{1}$ at $800-950^{\circ}C$ and ($\frac{6.2}{1}$) - ($\frac{6.5}{1}$) at $650-800^{\circ}C$, respectively. The defect structures and conduction mechanisms have been suggested.

• Current Optics and Photonics
• /
• v.5 no.2
• /
• pp.129-133
• /
• 2021

This study observed the performance of an InAs/GaSb type-II superlattice photodiode with a p-i-n structure for mid-wavelength infrared detection. The 10 ML InAs/10 ML GaSb type-II superlattice photodiode was grown using molecular beam epitaxy. The cutoff wavelength of the manufactured photodiode with Si3N4 passivation on the mesa sidewall was determined to be approximately 5.4 and 5.5 ㎛ at 30 K and 77 K, respectively. At a bias of -50 mV, the dark-current density for the Si3N4-passivated diode was measured to be 7.9 × 10-5 and 1.1 × 10-4 A/㎠ at 77 K and 100 K, respectively. The differential resistance-area product RdA at a bias of -0.15 V was 1481 and 1056 Ω ㎠ at 77 K and 100 K, respectively. The measured detectivity from a blackbody source at 800 K was calculated to be 1.1 × 1010 cm Hz1/2/W at zero bias and 77 K.

• Journal of applied mathematics & informatics
• /
• v.33 no.5_6
• /
• pp.579-591
• /
• 2015

Properties of prime filters are studied in BE-algebras as well as in commutative BE-algebras. An equivalent condition is derived for a BE-algebra to become a totally ordered set. A condition L is introduced in a commutative BE-algebra in ordered to study some more properties of prime filters in commutative BE-algebras. A set of equivalent conditions is derived for a commutative BE-algebra to become a chain. Some topological properties of the space of all prime filters of BE-algebras are studied.

• Korean Journal of Materials Research
• /
• v.24 no.10
• /
• pp.526-531
• /
• 2014

Thermal shock resistance property has recently been considered to be one of the most important basic properties, in the same way that the transverse-rupture property is important for sintered hard materials such as ceramics, cemented carbides, and cermets. Attempts were made to evaluate the thermal shock resistance property of 10 vol% TaC added Ti(C,N)-Ni cermets using the infrared radiation heating method. The method uses a thin circular disk that is heated by infrared rays in the central area with a constant heat flux. The technique makes it possible to evaluate the thermal shock strength (Tss) and thermal shock fracture toughness (Tsf) directly from the electric powder charge and the time of fracture, despite the fact that Tss and Tsf consist of the thermal properties of the material tested. Tsf can be measured for a specimen with an edge notch, while Tss cannot be measured for specimens without such a notch. It was thought, however, that Tsf might depend on the radius of curvature of the edge notch. Using the Tsf data, Tss was calculated using a consideration of the stress concentration. The thermal shock resistance property of 10 vol% TaC added Ti(C,N)-Ni cermet increased with increases in the content of nitrogen and Ni. As a result, it was considered that Tss could be applied to an evaluation of the thermal shock resistance of cermets.

• Journal of Korean Society of Water and Wastewater
• /
• v.27 no.4
• /
• pp.495-502
• /
• 2013

Hydraulic dead-zone and particle removal efficiency in the base frame of a constructed wetland was evaluated with computational fluid dynamics (CFD). The fraction of hydraulic dead-zone was estimated to be 1.2-2.1 % (v/v) and it was attributed to the artificial islands developed in the constructed wetland. Solids deposition rate could be increased with higher hydraulic retention time (HRT, ranged from 2.2 to 4.2 hr) of the wetland and larger particle size (ranged from 10 to $50{\mu}m$) in the influent. Experimental results showed that the volume concentration of the particles smaller than $10{\mu}m$ in diameter was varied from $1.99{\times}10^3{\mu}m^3/ml$ (HRT 12.8 hr) to $3.92{\times}10^3{\mu}m^3/ml$(HRT 2.2 hr) in the influent of the constructed wetland. With the effluent volume concentration data, removal efficiency of those particles was calculated to be 71.2 and 24.7 % when the HRT was 12.8 and 2.2 hr, respectively. Similar trend with the HRT variation could be identified with CFD analysis.