• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.605-609
• /
• 2001

Low density ceramic supporter was prepared by using fly ash as a starting material for the application to the biological aerated filter (BAF) system, and the effect of additives and sintering atmosphere on the apparent and bulk density of the carrier was examined. Borax, Na$_2$O and glass powders were added to produce liquid phase. The density of the supporter decreased as the amount of borax increased. The bulk density of 0.79 g/㎤ and the apparent density of 1.10 g/㎤ were obtained when the fly ash with 15% of borax was sintered at 116$0^{\circ}C$ for 15 minutes. The density also decreased as the plate glass powders past through 22${\mu}{\textrm}{m}$ size were mixed. When the fly ash with 12% of grass powder was sintered at 128$0^{\circ}C$ for 10 minutes, the bulk and apparent density were 0.90g/㎤ and 1.00 g/㎤, respectively. Apparent density of 1.6~1.8g/㎤ was obtained when the fly ash was sintered at 120$0^{\circ}C$ in a weak reducing atmosphere. By maintaining the reducing atmosphere and sintering at a high heating rate, the liquid phase was farmed from the reduced composition of fly ash. This resulted in the formation of closed pores that enabled the low apparent density.

• Tribology and Lubricants
• /
• v.15 no.1
• /
• pp.8-16
• /
• 1999

The electrorheological (ER) behavior of suspensions in silicone oil of phosphoric ester cellulose powder (average particle size : 18$\pm$1 ${\mu}{\textrm}{m}$) was investigated on the elevated temperature up to 10$0^{\circ}C$. For development of anhydrous ER fluids using at wide temperature range, it should be researched to how the effect of temperature on the ER activities. As a first step, the anhydrous ER suspensions mixing with the phosphoric ester cellulose particles which were made from the phosphoric ester reaction of cellulose were measured. As increasing the temperature, not only the analysis of electrical properties such as dielectric constant current density and electrical conductivity but also the rheological properties of ER fluids were studied. From the experimental results, the temperature had a large influence to the ER properties of anhydrous ER fluids. The current density, conductivity and elecoorheological effect ($\tau$$_{A}$$\tau$$_{0}$) of phosphoric ester cellulose ER fluids were proportional to the temperature with power law. And the shear stress of them was closely related with the square of dielectric constant mismatch parameter ($\beta$$^2$) under constant shear rate and electric field.d.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.213-217
• /
• 2001

본 논문에서는 CPW 구조를 이용하여 60 GHz 무선 시스템 응용을 위한 V-band용 하향 주파수 혼합기를 설계 및 제작하였다. 하향 주파수 혼합기의 설계 및 제작에 있어서 GaAs PHEMT(Pseudomorphic high electron mobility transistor)를 기반으로 하였으며, 회로설계를 위해 coplanar waveguide(CPW) 라이브러리를 구축하여 이용하였다. 제작된 하향 주파수 혼합기의 변환이득은 국부발진주파수(LO) 입력이 8 dBm일 때 -8.5 dB의 최대 변환이득 특성을 얻었으며 Pl dB는 -3.3 dBm을 얻었다. 제작된 회로의 칩 크기는 1.6$\times$l.6 $\textrm{mm}^2$ 이다.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.74-80
• /
• 1999

Work roll wear in the cold rolling of mild steel strip is strongly affected by rolling materials, rolling conditions such as roll arrangement in the cold rolling mill and lubrication. The tests were performed to find the effects of roll arrangement n the cold rolling mill on the work roll wear under the same lubricating conditions. The obtained results are as follows:If the distance of cold rolling is about 60km, the surface roughness of its was reduced by half(Ra 0.49${\mu}{\textrm}{m}$) and Pc(peak count) also was decreased to 60 ea/cm.It is easier for CC(Continuous casting) to make a slip on rolling than IC(Ingot casting). It is due to surface mirror in which first residual product appears and iron powder included Al2O3 is sticked. Because bending degree of 4Hi-rolling mill is higher than 6Hi-rolling mill, the first surface mirror was occurred to its center-point which is loaded strongly. 6Hi-rolling mill shape-controlled by intermediate roll doesn't need the initial crown to work roll. Therefore, fatigue and wear would appear a little bit.

• Journal of Korean Vacuum Science & Technology
• /
• v.3 no.1
• /
• pp.79-84
• /
• 1999

the photolithographic patterning on an indium-tin oxide (ITO) glass and the electro-phoretic deposition were combined for preparing the screen of the full-color field emission display(FED). the patterns with a pixel of 400$\mu\textrm{m}$ on the ITO-glass were made by etching the ITO with well-prepared etchant consisting of HCL, H2O, and HNO3. Electrophoretic method was carried out in order to deposit each spherical red (R), green(G), and blue (B) phosphor on the patterned ITO-glass. The process parameters such as bias voltage, salt concentration, and deposition time were optimized to achieve clear boundaries. It was found that the etching process of ITO combined with electrophoretic method was cost-effective, provided distinct pattern, and even reduced process steps compared with conventional processes. The application of reverse bias to the dormant electrodes while depositing the phosphors on the stripe pattern was found to be very critical for preventing the cross-contamination of each phosphor in a pixel.

• Journal of Welding and Joining
• /
• v.20 no.6
• /
• pp.830-837
• /
• 2002

This study investigated variations of micro-structures and mechanical properties of Ti / STS321L joint with various bonding temperature and time using brazing method. According to increasing bonding temperature and time, it was observed that the thickness of their reaction layer increased due So increasing diffusion rate and time. From the EPMA results, Ti diffused to the STS321L substrate according to increasing bending time to 30min. Hardness of bonded interface increased with increasing bonding temperature and time due to increasing their oxides and intermetallic compounds. XRD data indicated that Ag, Ag-Ti intermetallic compounds, TiAg and $Ti_3Ag$ and titanium oxide, $TiO_2$ were formed in interface. In tensile test, it was found that the tensile strength had a maximum value at the bonding temperature of $900^{\circ}C$ and time of 5min, and tensile strength decreased over bonding time of 5min. The critical thickness of intermetallic compounds was observed to about $30\mu\textrm{m}$, because of brittleness from their excessive intermetallic compounds and titanium oxide, and weakness from void.

• KSBB Journal
• /
• v.17 no.1
• /
• pp.54-58
• /
• 2002

Curdlan gel containing various hydrophobic materials was prepared. The homogenized suspension of curdlan and hydrophobic materials was healed at $100^{\circ}C$. The curdlan gel can contain hydrophobic material up to 27%(v/v). When gel was compressed, only water in the gel was removed. When immersed in water, the dried gel absorbed water and became the original wet gel. The syneresis of gel decreased with the concentration of hydrophobic material added. DHA content of dried gel was about 90%. $\beta$-cyclodextrin inclusion complexes containing DHA were prepared with addition of water and ethanol. X-ray diffractograms of complexes showed a specific peak at 7-$8^{\circ}C$ and FT-IR spectrum of complex showed a specific C=O peak at $1745\textrm{cm}^{-1}$. Inclusion complex containing DHA was microcapsulated with curdlan and pullulan.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.5
• /
• pp.108-113
• /
• 1997

In this paper, the optimum condition of (110) Si etching with the potassium hydroxide(KOH) etchant is presented. Although several researches on (110) Si anisotropic etching have been studied, there has been lack of effects of mask quality and etching conditions on the selectivity and the roughness o the etched surface. Three kinds of masks (film, emulsion and E-beam mask) were used in order to verify the effect of etching properties. Anisotropic bulk etching depends on the crystalline orientation and the concentration and temperature of the etchant. In order to investigate the effect of etching conditions on selectivity and the roughness of the etched surface, the concentration of the etchant was varied from 35 to 45 per cent in weight with increments by 5 per cent and the temperature was changed from 70 to 90$^{\circ}C$ with increments by 10$^{\circ}C$. The combination of the temperature of 70$^{\circ}C$ and the concentration of 40wt.% was found to be the optimum etching condition for high selectivity. Etched surfaces show minimum surfaces show minimum surface roughness at a temperature of 80$^{\circ}C$ and a concentation of 40wt.%. Comb structures with various comb widths were fabricated and the lengths of the combs wree measured with several etching time durations. A micro comb structure 525$\mu\textrm{m}$ high was fabricated for MEMS application.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.3
• /
• pp.238-244
• /
• 1994

We investigated solution growth of silicon on borosilicate and quartz glass substrates in the temperature range of $800^{\circ}C~520^{\circ}C$. A thin Al-Si layer evaporated onto the substrate serves to improve the wetting between the substrate and the Al/Ga solvent. Nucleation takes place by a reaction of Al with $SiO_2$ from the substrate. We obtained silicon deposits with a grain size up to a few 100 $\mu\textrm{m}$. There was a perferential (111) orientation for the case of quartz glass substrates while there is a strong contribution of other orientations for the deposition of Si on borosilicate glass substrates.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.9 no.2
• /
• pp.64-72
• /
• 2004

We measured the vertical profiles of $O_2$, H$_2$S, and pH in sediment pore water beneath marine cage fish farms using a microsensor with a 25 ${\mu}{\textrm}{m}$ sensor tip size. The sediments are characterized by high organic material load. The oxygen consumption, hydrogen sulfide oxidation, and sulfate reduction rates in the microzonations (derived from the vertical distribution of chemical species concentration) were estimated by adapting a simple one-dimensional diffusion-reaction model. The oxygen penetration depth was 0.75 mm. The oxic microzonations were divided into upper and lower layers. Due to hydrogen sulfide oxidation within the oxic zone, the oxygen consumption rate was higher in the lower layer. The total oxygen consumption rate integrated with reaction zone depth was estimated to be 0.092 $\mu$mol $O_2$cm$^{-2}$ hr$^{-1}$ . The total hydrogen sulfide oxidation rate occurring within 0.7 mm thickness was estimated to be 0.030 $\mu$mo1 H$_2$S cm$^{-2}$ hr$^{-1}$ , and its turnover time in the oxic sediment layer was estimated to be about 2 minutes. This suggests that hydrogen sulfide was oxidized by both chemical and microbial processes in this zone. The molar consumption ratio, calculated to be 0.84, indicates that either other electron accepters exit on hydrogen sulfide oxidation, or elemental sulfur precipitation occurs near the $O_2$- H$_2$S interface. Total sulfate reduction flux was estimated to be 0.029 $\mu$mol cm$^{-2}$ hr$^{-1}$ , which accounted for more than 60% of total $O_2$ consumption flux. This result implied that the degradation of organic matter in the anoxic layer was larger than in the oxic layer.