• The KSFM Journal of Fluid Machinery
• /
• v.4 no.4 s.13
• /
• pp.37-42
• /
• 2001

In the present study, flow characteristics of turbulent oscillatory flow in an oscillator connected to square-sectional $180^{\circ}$ curved duct are investigated experimentally. In order to investigate wall shear stress and pressure distributions, the experimental studies for air flows we conducted in a square-sectional $180^{\circ}$ curved duct by using the LDV system with the data acquisitions and the processing system. The wall shear stress at bend angle of the $150^{\circ}$ and pressure distribution of the inlet (${\phi}=0^{\circ}$) to the outlet (${\phi}=180^{\circ}$) by $10^{\circ}$ intervals of the duct are measured. The results obtained from the experiment are summarized as follows : wall shear stress values in the inner wall we larger than those in an outer wall, except for the phase angle (${\omega}t/{\pi}/6$) of 3, because of the intensity of secondary flow. The pressure distributions are the largest in accelerating and decelerating regions at the bend angle(${\phi}$) of $90^{\circ}$ and pressure difference of inner and outer walls is the largest before and after the ${\phi}=90^{\circ}$.

• Journal of the Korean Magnetics Society
• /
• v.4 no.2
• /
• pp.142-149
• /
• 1994

The Barkhausen noise was measured as the change of line width(39~1.22 mm) and scratching angle($90^{\circ}~50^{\circ}$) with respect of rolling direction in grain-oriented 3 % Si-Fe of 0.30 and 0.27 mm thickness. The two peak phenomena of the noise envelope observed for non-scratching and scratching of line width 39 mm was explained by large activation energy during $180^{\circ}$ domain wall nucleation and annihilation processes. The amplitudes of the noise envelpoes were decreased as the decrement of scratching line width, but did not almost changed below line width of 9.75 mm. It was explained that the decrease in the envelope with increasing scratching number is associated with lower activation energy of $180^{\circ}$ domain nucleation and annihilation in the vicinity of the scratching area. The noise power was decreased as narrower line width. The dependence of the power on the scratching angle was sharpest decreaded at the 50 angle.

• Imaging Science in Dentistry
• /
• v.47 no.3
• /
• pp.141-147
• /
• 2017

Purpose: The objective of this study was to compare the outcomes of surgical mini-implant placement when potential mini-implant sites were scanned using a lower-dose $180^{\circ}$ acquisition protocol versus a conventional $360^{\circ}$ acquisition protocol. Materials and Methods: Ten dentate human skulls were used to provide sites for potential mini-implant placement. The sites were randomly divided into 2 groups: $360^{\circ}$ and $180^{\circ}$ cone-beam computed tomography (CBCT) acquisition protocols. A small-volume $180^{\circ}$ CBCT scan and a $360^{\circ}$ CBCT scan of each site were acquired using a Morita Accuitomo-170 CBCT machine and then a mini-implant was placed. A follow-up $360^{\circ}$ CBCT scan was done as a gold standard to evaluate the location of the mini-implant and root perforation. Two raters evaluated the scans. Results: Ninety-eight percent of the mini-implants placed did not perforate any root structure. Two percent of the sites had an appearance suggestive of perforation. On a Likert scale, both raters agreed that their subjective evaluation of the diagnostic quality of the protocols, ability to make and read measurements of the sites, and preferences for the specified diagnostic task were comparable. The Cohen kappa showed high inter-rater and intrarater agreement. Conclusion: In this ex vivo study, we found that the $180^{\circ}$ rotational acquisition was as effective as the conventional $360^{\circ}$ rotational acquisition for the preoperative evaluation of potential mini-implant sites.

• Journal of Food Hygiene and Safety
• /
• v.13 no.2
• /
• pp.77-82
• /
• 1998

As a fundermental research for quality stailization of herb extract, the effects of water activity on microbial growth in herb extract were investigated. Herbs-Panax ginseng, Cinnamomum cassia, Lycium chinense, Zyzyphus jujuba, Lindera obtusilobum-were mixed and extracted with water at $80^{\circ}C$ and concentrated at $75^{\circ}C$. Water activity of the herb extract was adjusted to 0.86, 0.80 and 0.69, using water activity analyzer. The extracts were incubated for 180 days at $40^{\circ}C$ and then examined microbial cell counts and some physicochemical properties. In the extract of $a_{w}$ 0.86, 18 CFU/g of initial viable cell was increased to 80 CFU/g with 90 days of incubation and to 190 CFU/g 180 days of incubation. In the extract of $a_{w}$ 0.80, 24 CFU/g of initial viable cell was also increased to 83 CFU/g during the 90 days of incubation and to 170 CFU/ g for the 180 days of incubation. However, in the extract of $a_{w}$ 0.69, viable cell after 180 days of incubation was remained at almost the same level as initial viable cell. pH of herb extract was reduced in proportion to the decrease in water activity. The TLC (thin layer chromatography) patterns of ginseng saponins of herb extract did not show any significant changes after 180 days of incubation. Growth of pathogenic microorganisms was inhibited more with lower water activity of the herb extracts. In the herb extract inoculated with Candida albicans and Aspergillus niger, initial viable cells of 150 and 140 CFU/g were decreased to 30 and 20 CFU/g, repectively, after 30 days of incubation at $28^{\circ}C$. In the case of herb extract inoculated with Escherichia coli, Staphylococcus aureus, and Pseudomonas aeruginosa, growth of the bacteria was totally inhibited even after 30 days of incubation at $37^{\circ}C$.

• Textile Coloration and Finishing
• /
• v.10 no.4
• /
• pp.15-23
• /
• 1998

본 연구에서는 sizing을 포함하여 염색.가공 공정에서 습.건열 처리 온도를 변화시켜 처리한 폴리에스테르 필라멘트 사와 직물의 물성 변화에 관한 상관성을 연구하였다. 경사는 50d/24f(spark) 그리고 위사는 75d/72f(semi-dull)사를 사용하여 평직물을 셔틀직기에서 제직하였다. 사이징 공정에서의 건조온도를 $90^\circ{C}$, $125^\circ{C}$, $150^\circ{C}$로 변화 시켰으며 수세공정에서 습열 처리온도는 $90^\circ{C}$, $110^\circ{C}$ 그리고 $120^\circ{C}$로 변화시켰다. 그리고 프리세트 공정에서의 건열 처리온도는 $180^\circ{C}$, $200^\circ{C}$ 그리고 $220^\circ{C}$로 변화시켰다. 마지막으로 최종열처리 공정에서는 $170^\circ{C}$, $180^\circ{C}$ 그리고 $200^\circ{C}$로 각각 변화시켜 이들 직물의 인장, 굽힘, 전단 특성과 이들 직물에서 채취한 실의 탄성계수, 절단강도, 변형률 등을 측정하여 각 공정에서의 열처리 온도 변화에 따라 이들 물성치의 상관성을 검토 비교하였다.

• Proceedings of the Korea Contents Association Conference
• /
• 2005.05a
• /
• pp.156-164
• /
• 2005

The aim of this study was to analyze the isokinetic strength of ankle, lumbar and shoulder in fin swimmers. For this study, 7 male fin swimmers and 7 men general swimmers were selected. Isokinetic strength of ankle, lumbar and shoulder were measured by Biodex System 3,000. Statistical techniques for data analysis were a descriptive statistics and t-test. The results of this study were as following; The first, significant difference between two groups in right and left plantar flexion of ankle at $30^{\circ}/sec\;and\;180^{\circ}/sec$. But no significant difference was found between right and left in two groups. The second, significant difference between two groups in right dorsiflexion of ankle at $30^{\circ}/sec$. The third, significant difference between two groups in extension of lumbar at $60^{\circ}/sec$. The fourth, significant difference between two groups in right flexing of shoulder at $60^{\circ}/sec$ and $180^{\circ}/sec$. As result of this conclusion, the isokinetic strength of ankle and lumbar in fin swimming group showed significantly higher than non-fin swimming group.

• Korean journal of food and cookery science
• /
• v.9 no.4
• /
• pp.323-328
• /
• 1993

Benzo(a)pyrene [B(a)P], one of the polycyclic aromatic hydrocarbons (PAHs) is known as a potent carcinogen. As lipid consumption increases recently, the toxic effect of overheated lipid foods and fats ＆ oils were reported increasingly. In this study, the contents of B(a)p, other PAHs and rancidities of soybean oil were determined, and then the proper heating temperature, time and frequency were recommended, The work was carried out using soybean oil heated at $180\pm$5^{\circ}C$$, $200\pm$5^{\circ}C$$, and $300\pm$5^{\circ}C$$,for 50 hours. Acid Value(AV) and Conjugated Diene Value of samples were determined. The contents of B(a)P and other PAHs contents of all samples were masured by HPLC/UV method. The results obtained were as follows; Each content of PAHs in the fresh soybean oil was: Pyr 1.093, B(a)A 0.986, Ch 1.147, DMBA 1.082, B(e)P 0.664, Per 1.135, B(a)P 0.146, DBA 1.053, 3-MC 0.05 rg/kg. When the soybean oil was heated at $180\pm$5^{\circ}C$$, for 10, 20, 30, and 50 hours, B(a)P conterlts in heated soybean oils were 0.391, 0.692, 0.451, and 0.372 $\mu\textrm{g}$/kg respectively. Acid value of them were 0.26, 0.26, 0.29, and 0.33, and conjugated diene value was 0.67, 0.76, 0.99, and 1.04, respectively. When the soybean oil was heated at $200\pm$5^{\circ}C$$,and $300\pm$5^{\circ}C$$,for 10, 20, 30, and 50 hours, B(a)P coiltents in soybean oil heated at $200\pm$5^{\circ}C$$,were 0.844, 0.512, 0.479 and 0.247 Ig/kg respectively, Acid value 0.22, 0.21, 0.23 and 0.51 and CDNV 0.39, 0.49, 3.27, and 3.89. B(a)P contents in soybean oil heated at $300\pm$5^{\circ}C$$,were 0.466, 0.706, 0.607 and 0.247$\mu\textrm{g}$/kg respectively, Acid value 0.47, 1.57, 3.90, and 6.42 and CDNV 0.65, 2.15, 3.00, and 3.88.

• Journal of Korea Society of Industrial Information Systems
• /
• v.15 no.2
• /
• pp.11-16
• /
• 2010

In this papar, we have proposed a small electronically steerable parasitic array radiator with 180 degree azimuth beam coverage and high gain characteristics. The proposed antenna is composed of a uniplanar Yagi dipole as a feeding element and two dipoles as parasitic elements. The fabricated antenna is tested by electronically changing the reactance loaded on the parasitic dipoles and the results show that it has 5.2dB~6.7dB gain in $-90^{\circ}{\sim}90^{\circ}$wide azimuth range and -10dB return loss characteristics within 5.725GHz~5.825GHz UNII band.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.9 no.1
• /
• pp.47-53
• /
• 1995

In this paper, the characteristics of breakdown voltage($\textrm{V}_{Brms}$) -temperature(T) for air insulated power installation in flowing air with variation of T(30[$^{\circ}C$] -180[$^{\circ}C$]) are presented. To study these subjects, needle-to-needle gap in the circular pipe(inner diameter 5[cm]) are used. Also, theories of gas discharge and hydrodynamics in pipe were used to analysis for the characteristics. The $\textrm{V}_{Brms}$ is proportional to flow velocity. At high velocity, $\textrm{V}_{Brms}$ is described the saturation. At high T(180[$^{\circ}C$]), $\textrm{V}_{Brms}$ is about 4.7(kV] lower than low T(30[$^{\circ}C$]). The empirical equation obtained from this study is $\textrm{V}_{Brms}=A\times{Log[Re}+B$. Where A, B : Constant.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.15 no.3
• /
• pp.121-128
• /
• 2007

The purpose of this study was to investigate the removal efficiencies of HCl in dry reactor and Bag-Filter system. The bicarbonate was used as adsorbent to measure the HCl removal rate. The performance of bicarbonate was evaluated to investigate the removal efficiency. It was analysed that the best operation condition in using bicarbonate in process. The operating parameters was residence time, stoichiometric ratio, temperature and pressure. The Residence time was 1.5 sec, stoichiometric ratio was 1SR, 1.25SR, temperature was $160^{\circ}C$, $180^{\circ}C$, $200^{\circ}C$ and the bag filter pressure was 210mmAq, 230mmAq, 250mmAq. In this study it was found that the stoichiometric ratio and pressure can be effected in removal of HCl however the removal efficiency do not depends on temperature. The best operating condition was on 1SR, 230mmAq and $180^{\circ}C$ respectively and in this condition the best removal rate was 99.50%.