Recently, there has been considerably interested in the development to new functional gemini type anionic surfactant, sodium bis-n-alkyl sulfonatosuccinate, had been synthesized through the addition reaction of sodium bisulfite to bis-n-alkyl maleate, in which water was azeotropically distilled by adding benzene to the reaction system, gave a good yield. All the surface activities including krafft point, surface tension, emulsion power and foaming were measure and cmc was evaluated in dilute solution. This results showed a lower ability in $27{\sim}30dyne/cm$ than single-chain surfactant with $32{\sim}35dyne/cm$ to surface tension. Also its cmc value much smaller in $(6.5{\sim}10){\times}10^{-4}mca{\ell}/{\ell}$ than single-chain surfactant with $(40{\sim}45){\times}10^{-4}mca{\ell}/{\ell}$ concentration. In foaming ability and foam stability of gemini surfactant had especially a good ability in approximately $100{\sim}150ml$, and in emulsing power they exhibited a good emulsing phase and stability, and Krafft points were $0{\sim}10^{\circ}C$.

Resource recovery and recycling of materials and products, including polyurethanes is viewed as a necessity in today's society. Most urethane polymers are made from a polyol and a diisocyanate. these and be chemicals such as water, diamines or diols that react with isocyanate groups and add to the polymer backbone. The problems of recycling polyurethane wastes has major technological, economic and ecological significance because polyurethane itself is relatively expensive and its disposal whether by burning is also costly. In general, the recycling methods for polyurethane could be classified as mechanical, chemical and feedstock. In the chemical recycling method, there are hydrolysis, glycolysis, pyrolysis and aminolysis. This study, the work was carried out glycolysis using sonication ant catalyzed reaction. Different kinds of recycled polyols were produced by current method(glycolysis), catalyzed reaction and sonication as decomposers and the chemical properties were analyzed. The reaction results in the formation of polyester urethane diols, the OH value which is determined by the quantity of diol used for the glycolysis conditions. The glycolysis rates by sonication for the various glycols, increased as fallows: PPG

Density, viscosity, conductance, dye solubility and carbon-13 nmr studies were performed in aqueous solution of three disodium 4-n-alkyl-3-sulfonatosuccinate anionic surfactant at $20^{\circ}C$. The cmc values were 0.14 mol/l for the disodium-4-n-octyl-3-sulfonatosuccinate($R_{8)S$), 0.041mol/l for the disodium-4-n-decyl-3-sulfonatosuccinate($R_{10}S$), and 0.018mol/l for the disodium-n-dodecyl-3-sulfonatosuccinate <$R_{12}S$). The aggregation numbers determined viscometrically and conductimetrically were 28 for $R_{8}S$, 48 for $R_{10}S$, and 67 for $R_{12}S$. The volume changes upon micellization were $8.9cm^{3}/mol$ for $R_{8}S$, $9.5cm^{3}/mol$ for $R_{10}S$, and $10.1cm^{3}/mol$ for $R_{12}S$. Binding constants for the dye pada to the micelles and the fractions of unbound counter-ion were also obtained. The two polar heads with their carbon linkage were likely in an aqueous environment in the $R_{8}S$ micelles with the micelles themselves being spherical.

Micelle formation and adsorption at the $Ti0_{2}$ interface of a series of polystyrene-polythylene oxide(PS-PEO) block copolymer in aqueous solution was studied using fluorescence probing and small-angle X-ray methods. Further, the stability of aqueous $Ti0_{2}$ dispersion in the presence of copolymer was investigated by microelectrophoresis, optical density and sedimentation measurements. The dissolution of pyrene as fluorescent probe in aqueous surfactant solution leads to a slow decrease of the $I_{1}/I_{3}$ ratio, as the copolymer concentration increase; $I_{1}$ and $I_{3}$ are respectively the intensities of the first and third vibrionic peaks in the pyrene fluorescence emission. The behaviour was due to the characteristics of the copolymers and/or to the copolymer association efficiency in water. Moreover, the adsorption at the plateau level increases with decreasing PEO until chain length. The zeta potential of $TiO_{2}$ particles decreases with increasing copolymer concentration and reaches a plateau value. Finally, stabilization using block copolymers was more effective with samples having higher weight fractions of PS block.

Alkyl polyglucosides were synthesized by solvent-free glycosidation using ultrasonic emulsification. We examined glycosidation conditions of fatty alcohol with glucose hydrate and anhydrous glucose in the presence of p-toluenesulfonic acid. Glucose was emulsified in a molar excess of fatty alcohol for 20 minutes with a ultra-sonicator at room temperature and converted in a stirred reactor to more than 95% polyglucoside within $2.5{\sim}3.5$ hr under $20{\sim}30$ mmHg at $110^{\circ}C$ with a three-fold molar ratio of fatty alcohol to glucose in the presence of 1mol% p-toluenesulfonic acid. It was possible to obtain a polyglucoside mixture of HLB 13 consisting of 65% monoglucoside and 35% oligoglucoside with less than 1% of fatty alcohol.

Naphthothiazolo carbocyanine is of industrial importance as red-sensitizing dye in the spectral sensitization of emulsion microcrystals in negative film-making. In this study, red-sensitizing dye was prepared by the reaction of 2-methyl-3-sulfopropyl-4,5-naphthothiazolium(inner salt) with triethyl orthoacetate in the presence of triethylamine. The product was identified by using various analytical tools such as Elemental analyzer, IR spectrophotometer, UV-Vis spectrophotometer, Mass spectrometer, $^{1}H-NMR$ spectrometer, TGA and DSC. The maximum absorption peak in methanol solvent was 573nm. Therefore, it was concluded that naphthothiazolo carbocyanine dye can be used as red0sensitizing dye for the spectral sensitization of photographic emulsion.

Acrylic resin(ACR) was blended with a curing agent, hexamethoxymethylmela-mine(HMMM), in which blending ratio was 70:30. The curing behavior was examined using Rheovibron. Cross-linking reaction started at $170^{\circ}C$ in 2 min of reaction and curing was completed in 10 min. It was found that the extent of cross-linking increased with the content of acetoacetoxyethyl methacrylate monomer in the ACR.

Due to its low density, good mechanical properties and chemical inertness, glassy carbon(GC) has been studied for appications in several fields. A raw thermosetting resin of furanic resin was polymerized with a curing agent of p-toluenesulfonic acid monohydrate. The maximum yield of GC was obtained at the curing agent content of 1.0 wt% in furanic resin. In order to make thick GC, the affect of graphite filler addition to the furanic resin was investigated. The density and electrical resitivity of GC after graphitization were 1.45 $g/cm^{3}$ and 47 ${\times}10^{-4}$ ${\Omega}$ ${\cdot}$ cm respectively and the amorphous structure of GC was confirmed by XRD profiles with very broad peaks comparable to those of graphite at $206^{\circ}$ and $45^{\circ}$.