The object of this experimental study is to investigate the effect on frost prevention and delay by the method of alternating the function of outdoor coil rows under the frost conditions ($2^{\circ}C/1^{\circ}C$). The heat pump system with the new method can make frost delay time longer and eliminate frost effectively. It is withstand over 280 minutes without a conventional defrosting method. Maximum COP in case of adopting new method is 13% higher than that in case of reverse cycle defrosting method. Also in case of moving air injection duct faster, the frost delay time is lengthened and its COP is enhanced more.

Thermal analysis of a cooling module using Peltier elements are performed using a commercial software, CFD-ACE+. A standard k-e two-equation turbulent model is applied in order to represent the turbulent shear stress. Computed values are compared with the theoretical values for the validation. The effect of mass flow rates and transferred heat amounts on the temperature distributions inside the cooling system is analyzed. It was found that the increase in the mass flow rates causes the exit temperature rise. The increase in the absorbed heat amount diminished the overall temperature on the fin surfaces. In the present analysis, the material characteristics of the Peltier element itself are not considered. In the future, the effect of the turbulence models and material characteristics will be studied in detail.

Structural analysis of a tire is done using a commercial software, ANSYS Workbench. The properties of rubber of the tire is represented using a Mooney-Rivlin model. The bead in the tire is made of structural steel. 3D CAD model of the tire is obtained from a commercial CAD-specialized software, CATIA. Using an imported 3D CAD geometric model, a mesh system with fifty thousand nodes is constructed using ANSYS. A time-variant point force is applied to the rim of the tire, and the deformation of the tire is computed. It is found that both bending and twisting of the tire are observed where the point force is applied. The deformation of the tire is asymmetric, which results in the help of ripping the tire using the helper. It is also found that the deformation undergoes linearly with the applied force. When the force is larger than 1500N, then the deformation becomes larger than the half of the thickness of the tire. In the future, a more realistic rubber model will be applied and validated with the measured data.

The car industry is one of the technological applications which more rare earth metals employes as three-way catalysts. Therefore, the recovery of rare earth metals from the used automotive three-way catalysts could be important source to obtain these metals. This work presents the analysis of market and demand for rare earth metal in automotive three-way catalyst and introduces the dry and the wet processes for the recovery of rare earth metals from used three-way catalyst. Finally, the alternative methods to conventional wet processes was simply suggested based on the economic and ecological point of view.

Shaping an input command through considering the resonant modes of multi degrees of freedom system, it is possible to realize the wanted motion, without exciting the uncontrollable modes of the flexible system. But, an increase of modes to be considered brings inevitably about the time delay due to an excessive rising time. On the purpose of reducing the rising time, only the interesting and dominant modes can be considered to determine the timing pulses of input shaper. In this paper, an effect of shaper by the partial modes is analysed for a specific system and the input shapers by the partial modes are analysed for three d.o.f damped system, using Matlab simulation.

The purposes of this study are predictions of the changes in the section geometry and determination of the initial cross section so that opposite side in height direction is exactly parallel after coiling process. Finite element analysis is carried out for the calculation of the sectional changes for mold spring item. Analysis results reveal that the slope of the top and bottom sides varies in the range of 5 to 8 degrees and the amount depends on the dimension of the outer diameter. The slopes of the sides should be defined first among design variables.

This study is performed to investigate the effect of the artificial light for room lightening. To do that, the experiments were done using the black room with 1m3 and performed to show the effect of the length between the room and light source and light intensities as LUX. The LUX of 18 sites in the room was measured using LUX meter. The length between the room and the light source was chosen as 500mm, 1000mm, and 1500mm and the light intensities was 3 levels. The results were shown the distinct difference between the part directly projected through the light path and non-directly projected. So, the light delivery path have to be modified for next step research. The results were very sensitive for the part directly projected through the light path. This study showed the basic results for room lightening using light source to simulate the solar lightening and was worth in a strict sense as fundamental study.

In this paper, a hybrid design tool combining one-dimensional(1D) lumped model and three-dimensional computational fluid dynamics(CFD) approach has been developed in order to evaluate the performance of inkjet print head and droplet control process are studied to reduce the deviations between nozzles which affect the size of the printed line for the industrial application of direct writing on printed circuit boards(PCB). 1D lumped model analysis shows that it is useful tool for evaluating performance of an inkjet head by varying the design parameters. The differences in ejected volume and droplet velocity between analytical and experimental result are within 12%. Time sequence of droplet generation is verified by the comparison between 3D analysis result and photographic images acquired by stroboscopic technique. In addition, by applying DPN process, velocity and volume uniformity between nozzles is dramatically improved that the tolerance achieved by the piezoelectric inkjet printhead across the 64 nozzles is 5 to 8%. A printed line pattern is successfully obtained using the fabricated inkjet print head and droplet calibration system.

With the world-wide demand on the emission minimization, the needs on the diesel aftertreatment devices with high efficiency are also increasing. In order to effectively develop or design a high-performance diesel particulate filter, a clear understanding on the deposition and regeneration mechanism is required. In the present study, a theory on the lumped parameter model for wall-flow type diesel particulate filters is described focusing on the deposition efficiency, pressure drop inside the filter. The fourth order explicit Runge-Kutta method is utilized for the mass flow rate computation. Engine operation modes with controlled and uncontrolled regeneration options are selected. The computational lumped parameter model is validated by comparing the computed results with the measured data.

Transdermal drug delivery device is a method of drug delivery through the skin. Skin has a very large area, so it is attractive route to drug delivery. When drug delivery through the skin, microneedle has a advantage that painless, constant drug deliver and penetration efficient; nevertheless the cost is expensive because fabrication process need a particular equipment and not suitable in mass production. This study shows microneedle fabrication process using convergence of general MEMS process and dicing process that can make 3-D sharp microneedle tip and this fabrication process suitable for mass production.