Although the high speed machining technology (HSM) has been significantly studied in worldwide for past two decades, and has been widely applied in machining processes at many countries, it is not well known in domestic machining industries. The objective of this article, therefore, is to introduce the HSM to domestic industries so that they can apply the HSM on their products and results in improvements on productity and precision. The concept of HSM, tool materials and tool wear of HSM, surface roughness of HSM, and the chip shape of HSM are discussed.

In grinding operations, one of the most important problems is to increase efficiency of process. In order to achive this purpose, it is necessary to administer the tool life of grinding wheel and to optimize grinding conditions. Frequently dressing result in lowering the process efficiency remarkably and makes production cost high. On the other hand, grinding with a worn wheel causes the workpiece surface roughness to increase and often results in the occurrence of such troubles as chatter vibration and burning.

This paper aims to clarify the effects of grinding conditions on the ground surface and bending strength in surface grinding of various ferrites with diamond wheel. The main conclusions obtained were as follows. The surface roughness becomes better at lower wheel speed in the case of v/V=1$\times$10-3, and the condition of v/V=1$\times$10-4shows the best performance for the finish grinding. When the relative contact temperature becomes lower at a constant value of v/V, the ground surface exhibits lower roughness. The ground surface shows that the fracture process during grinding becomes more brittle at the higher value of v/V. The damage depth which affect the bending strength is below 10$\mu$m in the grinding condition of S=10㎣/mm.s with the diamond tool after dressing & truing, however, the depth increases with increasing removal rate(S). When the strength degradation due to grinding is larger, the removal depth for the recovery of strength requires a larger size.

One of the crucial problems that must be solved in a computerised unmanned machining environments requires the development of algorithm in order to predict the reliable cutting conditions on surface roughness. This paper is to develop the mathematical models for choosing the suitable cutting conditions and assist a comprehensive understanding of its machinability properties for cutting process by Ball End Mill. The mathematical equations developed to predict the surface results. It has been found that theoretical results obtained from the empirical equations agree with the experimental results of surface roughness.

In-process monitoring of cutting conditions and tool wear is important for improving productivity. This paper is concerned with on-line monitoring of tool wear and cutting force in end milling operation. The experimental study deals with the relations between flank wear and cutting force signal. Tool wear is detected by monitoring of cutting signal. A monitoring procedure is shown in this paper. The influence of flank wear on cutting signal activity was examined. The results are presented in the form of graphs. The analysis of the cutting signal and flank wear curves provides useful indicators of unacceptable wear development in the tool.

Determination of effective EDM parameters is significant to increase productivity. However, With the complexity of EDM phenomena, a universal selection method of EDM parameters has not been established yet. Moreover, No attempt has been tried before to suggest a logical method in determining essential machining parameters for effective electrical discharge machining. Peak current, one of the most significant factors in EDM, is proportional to EDM area. This paper presents a method that can be Z-map modeling from CMM data, and calculate EDM area using Z-map.

Among the non-traditional machining methods, Abrasive waterjet machining process shows big promise in drilling difficult-to-machine materials due to its numerous advantages such as absence of heat affect zone and thermal distortion. Acoustic emission signal technique is used to understand about material removal mechanisms during abrasive waterjet drilling process. More information about the drilling process is derived through frequency decomposition of auto regressive moving average modeling representing acoustic emission signals.

Case hardening of tool steel(SK5) was investigated after YAG laser irradiation. In the case of beam passes, martensite formed in the melt zone and in former pearlite regions of the austenization zone exhibited very high Vickers Hardness values. The molten depth and radius, micro structure, hardness were investigated as a function of defocusing distance, pulse width, and power density.

We need to achieve th mass product through methods of higher efficient, higher precise manufacturing process than those of existing precision abrasive machining. Thus, this study is to develop mirror-like surface machining technique of outer diameter of the piston pin by the compound magneto-electrolytic abrasive polishing system. The procedure of machining is followed as first, fulfill the pre-processing by cylindrical grinder, second, complete mirror-like surface by the method of magneto-electrolytic abrasive polishing used CBN non-woven abrasive pads. In this study, it was found that the best suitable conditions of mirror-like surface polishing were that the electrode density was 0.1A/$\textrm{cm}^2$, the applied pressure 1.5kgf/$\textrm{cm}^2$, the feed rate 0.5mm/rev, and the rotoation velocity of workpiece 80rpm, and that the surface roughness was reduced in this conditions.

In this paper, we developed a Windows 95 version off-line programming system which can simulate a track vehicle model in 30 graphics space. The track vehicle was adopted as an objective model. The interface between users and the off-line program system in the Windows 95's graphic user interface environment was also studied. The developing language is Microsoft Visual C++. Graphic libraries, OpenGL, by Silicon Graphics, Inc were utilized for 3D Graphics.

This study deals with the friction weldability of A7075-T6 having high specific strength. The friction welding conditions used are rotation speed 2000rpm, friction pressure 40MPa, friction time 1.5sec, upset pressure 40~100MPa, upset time 5sec. First, upset length was measured by displacement transducer. The plastic flow in 7075-T6 weld generates convex lens shaped resion by friction and concave lens shaped resion by axial force. Under the condition of upset pressure 85MPa, the friction welds have tensile strength of 552MPa and shear strength of 262MPa.

The purpose of this study is the generation of B-spline surface by the 3D measurement data. The hardware of the system comprises PC and digitizing machine, machining center. There are three steps, (1) physical model measuring on the 3D laser digitizing machine, (2) B-spline surface modeling and Fairing, (3) CNC machining by the NC code. It is developed a software package, with which can conduct a micro CAM system in the PC without economical burden.

Laser printer, faximile and copy machine are a few examples of OA(office automation) system. In such a system, the reflecting mirror has been employed for transmitting a target image to optical device. Therefore, to develope a good quality of optical system, the quality control of optical mirror was required. In recent years, considerable efforts have been directed toward the development of automated optical glass inspection system because the inspection is eye-fatigue and monotonous job for humans to perform. In this paper, we propose a inspection system applying algorithm of image processing for detecting defects of optical glass such as pinhole, scratch. From the experiments, the proposed inspection system shows reliable results.

This paper presents a new solution approach to moving obstacle avoidance problem for a mobile robot. A new concept avoidability measure(AVM) is defined to describe the state of a pair of a robot and an obstacle regarding the collision between them. As an AVM, virtual distance function(VDF) is derived as a function of the distance from the obstacle to the robot and outward speed of the obstacle relative to the robot. By keeping the virtual distance above some positive limit value, the robot avoids the obstacle. In terns of the VDF, an artificial potential field is constructed to repel the robot away from the obstacle and to attract the robot toward a goal location. At every sampling time, the artificial potential field is updated and the force driving the robot is derived form the gradient of the artificial potential field. The suggested algorithm drives the robot to avoid moving obstacles in real time. Since the algorithm considers the mobility of the obstacle as well as the distance, it is effective for moving obstacle avoidance. Some simulation studies show the effectiveness of the proposed approach.

The CAD system which enables to design and draw the screw thread gauges was developed and constructed. This system was proposed based on Visual C++ Version 5.0. Even beginner can get drawings as well as concerned data for the manufacturing of screw thread limit gauges by selecting the input data. This system was constructed from relevant standards and regulations (based on the Korean Standard and referred to ISO and JIS), handbooks and textbooks. The system shall provide more powerful and user friendly tool for design and drawing for screw thread gauges such as metric fine and coarse threads, unified fine and coarse threads, Parallel and taper pipe threads. The results of this system are proved to be in good agreement with concerned standards and regulations.

Image processing was used to recognize parts at various disposition. Non-transpatent tachometer panel for automobile and semi-transparent panel have been used as test specimen. Laplacian filter and various threshold values have been applied for preprocessing and edge following algorithm has been applied. Series of length data between edges have been generated from each image and compared using cross correlation coefficient. The result using cross correlation coefficient. The result using both edge following and cross correlation coefficient was proven to be the best fit for the proposed parts.

NC code has to be made after changing the drawing information to DXF file, the converting file. Arranging the information ordered irregularly when DXF file is made decrease the unnecessary time of rapid feed during working and the DATA capacity when the information is changed. This CAM program can be used easely for the beginner of the minor enterprises. The connection of operations and the use of GUI increase business efficiency.

The objective of this study is to investigate effects of prebuckling on the buckling of laminated composite cylindrical shells. Axial compression is considered for laminated composite cylindrical shells with length to radius ratios. The shell walls are made of a laminate with several symmetric ply orientations. This study was made using finite difference energy method, utilizing the nonlinear bifurcation branch with nonlinear prebuckling displacements. The results are compared to the buckling loads determined when membrane prebuckling displacements are considered.

The misalignment state causes some problems in operating. These problems such as vibration, noise, make the reduce wear, as well as, a stress concentration on the coupling which is the very weakness point at the morter. In order to align the shaft, the dialgage method has used as a means of solution until now. The method using a dialgage require a great deal of labour and money due to making by hand, the accurate alignment is not up to the expectation. For aligning the shaft, all the rotor must come to accord. Also, the dialgage method cannot be compared with straingage measurement method, from the viewpoint, which can gage in short time.

In fracture problems, stress intensity factors obtained theoretically and experimentally have been effectively utilized in the analytical evaluation of the cracks effect. The effect of surface crack of a cylindrical and a hollow cylindrical bar is investigated, as well as the effect of the thickness of a hollow cylindrical bar and inclined crack of a hollow cylinder subjected to torsion moment. In this study, stress intensity factor Km of mode III which expresses the stress state in the neighborhood of a crack tip is used. Stress analysis was conducted of the inside of a hollow cylinder in the axial direction of three dimensional crack tip subjected to torsion moment by combining the caustics method and the stress freezing method.

STL which is used in Rapid Prototyping is composed of a lot of triangular facets. The number of triangles and the shapes of these triangles determine the quality of STL. Therefore, proper algorithm is necessary to enhance the quality of triangular patch. In this paper we used the Delaunay triangulation method to apply to following processes. 1) On processing for reducing sharp triangles which cause errors on intersection. 2) On processing for connecting two or more collinear edges. 3) On processing for deleting unnecessarily inserted points in coplanar polygon.

The performances of cutting process is mostly affected by the characteristics of closed loop system constructed with machine tool structure, work piece and tools. The chucking system is very important component in this system to hold work piece correctly in various static and dynamic load condition. Therefore, chucking force and accuracy must be considered carefully, from these reason, this paper describes the stability of chucking system which preserve high stiffness and accuracy of machine tool system.

As the accuracy of manufactured goods needed high-accuracy processing has made the efficiency of NC and measurment technology develop, the innovation of machine tools has influence the development of the semi-conductor and optical technology. We can mention that a traction role of the acceleration for the development like that depends on the development of the measurement technics - Stylus instrument method, STM, SEM, Laser interferometer method - which are used for measuring the movement accuracy of machine tools. The movement error factors in movement accuracy are expressed as yaw, roll, and pitch etc. Machining center has 21 movement error factors including of 3 axies joint errors because that has 3 axies and has been measured as the standard of the unloaded condition until now inspite of getting static, dynamic, and servo-gain errors in the case of expending the error range. Therefore, this study tries to measure position accuracy according to loading on the X-Y table of the machining center.

In order to control thermal deformation of machine origin of machine tools due to internal and external heat sources, the real-time compensation system has been developed. First, GMDH models were constructed to estimate thermal deformation of machine origin for a vertical machining center through the measurement of deformation data and temperature data of specific points on the machine tool. Thermocouples and gap sensors are used respectively for measurement. These models are nonlinear equations with high-order polynomials and implemented in a multilayered perceptron type network structure. Secondly, work origin shift method were developed by implementing digital I/O interface board between CNC controller and IBM-PC. The work origin shift method is to shift the work origin by the compensation amounts which is calculated by pre-established GMDH model. From the experimental result, thermal deformation of machine origin was reduced to below $\pm$5${\mu}{\textrm}{m}$.

This study describes a theoretical and experimental investigation of gas wave propagation in the pipe system. Most calculations of compressible flows in the pipe have been based on the method of characteristics. This technique has propensity to truncate waves and is difficult to apply to non-perfect gas. A method that describes the application of a two-step Lax-Wendroff acheme to solution of the unsteady one-dimentional flow in the pipe was developed. Theoretical calculations using both the method of characteristics and the two-step Lax-Wendroff method are presented including a realistic model for heat transfer and friction processes. In the present work, account is taken of the nonlinear behavior. For sections of parallel pipe, an one dimensional unsteady homentropic analysis is employed, and a numerical solution is obtained with the aid of a digital computer, using the method of characteristics and two-step Lax-Wendroff method. This analysis is then combined with boundary models, based on a quasi-steady flow approach, to give a complete treatment of the flow behavior in the pipe system.

An experimental study on the prediction of grinding wheel wear by dual detection methods was conducted by the laser displacement and acoustic emission(AE) system. The laser displacement sensor was located above the head of the grinding wheel and the AE sensor was set under the workpiece, where the wheel were condition can be detected. It was found that the dual detection methods by laser displacement system and AE system made it possible to predict the wheel wear. From the experiments, the root mean square(RMS) values both methods was found to be proportional to the grinding wheel wear.

This paper examines the crack growth behavior of 7075-T651 and 5052-H32 aluminum alloys for variable load within tensile load range condition. The cantilever beam type specimen with a chevron notch is used in this study. The crack growth and closure are investgated by compliance method. The applied initial stress ratio is R=0.3 and variable load are R=0.65, 0.46. Crack length, stress intensity factor range, ratio of effective stress intensity factor range and crack growth rate etc. are inspected with fracture mechanics estimate.

In the CNC lathe working, the study of the effects of various cutting conditions on cut surface roughness is less active than that of the ordinary latee. After lathe working of SM45C, a carbon steel material for machine structure, its surface roughness was measured using a stylus surface roughness tester. In most cases, good surface roughness was obtained over 160m/min cutting speed and then the proper cutting depth was found as 1.0~1.5mm.

The guidance core is a principal part installed between the ink and the pen nib for the function of supplying ink to paper with reqularity. The current measurement of this product, Guidance core, in service is done by on operator with a micrometer, which could result in the decrease of productivity and working efficiency as well as causing errors. In this study, the existing measurement of the dialmeter of the Guidance core in the centerless grinding process is changed to the inprocessor measurement which enables consecutive measurement during the production of the Guidance core, and this system is also developed to work properly under bad circumstances and to have superior reliance and operational efficiency.

Recently, developments in the frontier industry have brought a rapid increase in the use of brittle materials such as silicon wafer, ferrite, sintered carbide, MgO single crystal and die steel. Because of high hardness and brittleness the cracking and chipping are apt to generate in the grinding of brittle materials, but have replaced gradually the high precision grinding. In this study, the optimum system of in-process electrolytic dressing controlled by computer was developed for improving the defects, and could maintain the optimum dressing condition at all times. The control of in-process dressing was simplified using this system, was able to maintain a stable dressing current and was unrelated to the change of dressing condition according to the variation of gap and oxide layer. Therefore, the optimum in-process electrolytic dressing system was constructed and the analysis of grinding mechanism with this system was studied.

Materials of the Frame hole in fishing trackle reel is made up a number large and small holes. Thus, it is difficult to effective machining. Abrasive flow machining(AFM) is useful to polish a internal or external surface of the 3-dimensional shape parts, which are used in many fields such as aerospace, automative, semi-conductor, and medical component industries. The machining process is that two hydraulic cylinders, which are located face to face, enforce abrasive media to the passage between workpiece and tooling parts alternately, and then the abrasives include in the media pass the passage and polish the surface of workpiece. The media which is made of polymer and abrasives plays the role of the tool for deburring or polishing complex shap workpiece by its viscoelastic characteristics. In this study, the abrasive media for abrasive flow machining was made by mixing viscielastic polymer with alunina and silicon carbide abrasive. Also, we present AFM device design and preliminary results of an investigation in to some aspects of the AFM process performance in fishing trackle reel.

This study considers flowshop scheduling problem related to flexible maufacturing cell in which consists of two machining centers, robots for loading/unloading, and an automated guided vehicle(AGV) for material handling between two machining centers. Because no machinng center has buffer storage for work in process, a machining center can not release a finished job until the empty AGV is available at that machining center. While the AGV cannot tranfer an unfinished job to a machining center until the machining center empty. In this paper, an new heuristic algorithm is given to find the sequence that minimize their makespan.

The determination of sound pressure radiated from periodic plate structures is fundamental in the estimation of noise levels in aircraft fuselages and ship hull structures. As a robust approach to this problem, here a very general and comprehensive analytical model for prediction the sound radiated by a vibration plate stiffened by periodically spaced orthogonal symmetric beams subjected to a sinusoidally time varying point load is developed. The plate is assumed to be infinite in extent, and the beams are considered to exert both line force and moment reactions on it. Structural damping is included in both plate and beam materials. From this theoretical model, the sound pressure levels on axis in a semi-infinite fluid(water) bounded by the plate with the variation in the loactions of an external using three numerical tools such as the Gauss-Jordan method, the LU decomposition method and the IMSL numerical package.

In this pater, a method of strength evaluation applying fracture mechanics in adhesively bonded joints of A1/A1 materials was investigated. Various adhesively bonded joints of double-cantilever beam with a interfacial crack in its adhesive layer were prepared for the fracture toughness test of comprehensive mixed mode conditions from nearly pure mode I to mode II. The experiment of fracture toughness was carried out under various mixed mode conditions with an interfacial crack and critical energy release rate, Gc by the experimental measurements of compliances was determined. From the results, fracture toughness on mixed mode with an interfacial crack is well characterized by strain energy release rate and a method of strength evaluation by the fracture toughness in adhesively bonded joints of A1/A1 materials was discussed.

We developed a Off-Line Graphic Simulator which can simulate a robot model in 3D graphics space in Windows 95 version. 4 axes SCARA robot was adopted as an objective model. Forward kinematics, inverse kinematics and robot dynamics modeling were included in the developed program. The interface between users and the off-line program system in the Windows 95's graphic user interface environment was also studied. The developing language is Microsoft Visual C++. Graphic libraries, OpenGL, by Silicon Graphics, Inc. were utilized for 3D graphics.

Recently, the uses of ceramic/metal bonded joints for structural materials have increased in various engineering fields such as automobiles, heat engines, and so on. A method of strength evaluation focussing on fracture criterion of mixed was investigated in Si3N4/metal bonded joint. Also, Fracture toughness tests of Si3N4/metal bonded joints with an interface crack were carried out and the stress intensity factors of these joints were analyzed by boundary element method. From the results, the fracture criterion and method of strength evaluation by the fracture toughness were proposed in Si3N4/metal bonded joints

ESP(Electronic Speckle Pattern Interferometry) is an optical technique to measure deforamtion of engineering components and materials in industrial areas. ESPI, a non-contact and non-destructive measuring method, is capable of providing full-field results with high spatial resolution and high speed. One of important application aspects using electronic speckle pattern interferometry is to generate contours of a diffuse object in order to provide data for 3-D shape analysis and topography measurement. The electronic speckle contouring is suitable for providing measurement range from millimeters to several centimeters. In this study, we introduce the contouring method by modified dual-beam speckle pattern interferometer and a shift of the two illumination beams through optical fiber in order to obtain the contour fringe patterns. Before the experiments, we performed the geometric analysis for dual-beam-shifted ESPI contouring. And by this geometric analysis, we performed the electronic speckle contouring experiment. We used 4-frame phase shifting method with PZT for quantitative analysis of contour fringes. Finally, we showed good agreements between the geometric analysis and experimental results.

This thesis is concerned with the development of useful engineering techniques to detect and analyze nonlinearities in mechanical systems. The methods developed are based on the concepts of higher order spectra, in particular the bispectrum and trispectrum, and the Volterra series. The study of higher order statistics has been dominated by work on the bispectrum. The bispectrum can be viewed as a decomposition of the third moment(skewness) of a signal over frequency and as such is blind to symmetric nonlinearities.

The distribution of fatigue crack growth rate is subjected to the measuring interval and calculated method of growth rate. In this paper, in order to establish the method of determining the distribution of fatigue crack growth rate, which ignores those influences, a series of fatigue crack growth experiments and measuring intervals of crack length calculated reasonable are presented. The main conclusions obtained are summarized as follows: 1) As a result of the ΔP constant test and ΔK constant test, it is thought that an approximate measuring interval of 0.3~0.7mm is reasonable, which allows for few errors and is little subjected to the calculated method of crack growth rate.

A structural design based of finite element analysis has been performed to investigate the reliable automatic transport system. For the procedure, different cross-sectional geometric factors were calculated and compared in detail. The von-Mises stresses were chosen to maintain a solid loading braring capacity for the safe design. Parametric studies showed that it is more inportant for the plate bending problem than the vertical loads of hanging bar to assess the safe and economic structural design.

Development of high speed feed drive system has been a major issue for the past few decades in machine tool industries. The reduction of the tool change time as well as rapid travel time can enhance the productivity. However, the high speed feed drive system generates more heat in nature, which leads thermal expansion that has adverse effects on the accuracy of machined parts. The detail of the model proposed is described in the paper together with the experimental methodologies using a proposed compact measurement system to examine the validity of the proposed approach. The results showed the machining accuracy could be maintained to better than $\pm$5${\mu}{\textrm}{m}$ while using this T-18 sensor

The failure of material structures or mechanical system is considered as a direct or indirect result of fatigue. In the design of mechanical structure for estimating of reliability, the prediction of failure life is the most important failure mode to be considered. However, because of a complicated behavior of fatigue in mechanical structure, the analysis of fatigue is in need of much researches on life prediction. This document presents a prediction of fatigue life of the SAPH45 steel, which is extensively for vehicle frame. The method using lethargy coefficient and stress distribution factor at pediction of fatigue life based on the consideration of the failure characteristics from the tensile test should be provided in this study.

The welding technology and qualities are developed significantly, in recent years, in the use of automated processing technology and welding robot systems. But these automated welding technologies have many difficulties for finding the optimal welding parameter conditions. Because of the lack of mathematical model for determination of optimal welding process parameters. In this study, the sensitivity analysis of the empirical equations for finding weld bead width, height and penetration depth by using the published formulae. The selected major welding process parameters effected to weld bead geometries are the welding speed, current, voltage and weld wire diameter.

In this paper, a Helmholtz resonator type hydraulic filter is proposed to absorb flow and pressure ripple produced from a axial piston pump. The basic principle of hydraulic filter is applied to propagation of preossure waves, reflection, absorption in cross section of discontinuity and resonance in the pipeline. This filter has advantage of the compact size and high degree of freedom of installation. The design scheme of hydraulic filter based on viscous wave theory are developed and manufactured two kinds of filter to investigate damping capability. It is experimently confirmed that these filter is absorbed to be about 20dB of flow and pressure ripple with high frequencies.

In this study behavior of fatigue crack and fatigue fracture is observed under rotary bending fatigue testing in friction welded dissimilar materials. Fatigue fracture most occurred in SM15C heat affected zone around Interface. In case of fatigue test, stress is reduced the position of fracture gradually moves to the welded Interface. Micro crack of heat affected zone surface on SM15C is observed at any different stress.

A method for the evaluation and the compensation of the vertical milling machine is presented. The method used a mathmatical model of thermal deformation based on temperatur variations of the machine and the environment. It follows an empirical approach and requires low cost equipment to be applied. According to this study, machine error caused by thermal deformation will be reduced to about 1/6.

Most of mechanical structures are combined of substructures such as beam and/or plates. There are few system with unibody structures but are not a few systems with united body structures. Generally the dynamic analysis of whole structures is perform ed under alternating load. However, the analysis of each joint area is more important than others for zero severity. This paper presents the results of analysis of concentration stress in bolt jointed structure with variable preload. At frist, a static vibration test was performed to find out a nominal stress of bolt joint ed plates from the relationship between natural frequency and nominal stress. Then a concentration stress was computed at contact point between bolt and plate in the structure. It is believed that the proposed method has promising implications for safer design with fatigue quality index of stress concentration factor and has merit for cost down and saving time at the beginning of vehicle development.

In recent truck industry, ride quality improvement as well as payload capacity is a very important subject. In order to achieve this goal, it is necessary to study several sub-systems (powertrain, suspension, engine mount, exhaust, etc) of truck which are major components of vehicle. In this research, torsional vibration reduction method of 4$\times$2 truck powertrain is demonstrated by using computer simulation and experiment. First, truck powertrain is modeled as a vibration system and validity of developed model is verified by comparing free vibration results with experiment results. Second, Most key parameters which influence torsional resonance are examined utilizing mode analysis. Finally, frequency responses of truck powertrain are obtained and reduction counterplans of torsional vibration are suggested.

This study includes noise automatic inspection system for washing machine auto-transmission one of modern home necessary. We effort to find and certificate sound noisesource by sound power and sound intensity, and apply to frequency analysis in vibration related sound noise. Still more we have been studying to data acquisition and programming for MS VisualBasic version 5.0. System component is below. 1) Pentium PC for data acquisition. 2) DSO for noise acquisition. 3) S/W for comparison and decision. 4) I/F Board for data communication. Wave form data through the DSO are converting to ASCII code data. The ASCII code through binary converting S/W are to be decision fitness or the badness comparison S/W. Finally, we will making noise monitoring system and automatic inspection system.

Super precision working technique and machine tool have been developing continually thanks to advanced electronic field. To obtain good result. it is necessary to investigate surface state in grinding with ${\mu}{\textrm}{m}$ level. There were so many researches to satisfy these demands using non-contact methods through the computer vision. In this study, the texture of working surface was analyzed. cooccurrence matrice was obtained from the surface roughness. Texture parameter was obtained by means of position operator compose of $\theta$. d according to variation of angle direction and distance. As a result, it was found that surface texture was more effected by direction ($\theta$) then distance(d).