The stability condition of rock slopes is greatly affected by the geometry and strength parameters of discontinuities in the rock masses. Rock slopes Involving movement of rock blocks on discontinuities are failed by one or combination of the three basic failure modes-plane, wedge, and toppling. In rock mechanics, practically all the parameters such as the joint set characteristics, the rock strength properties, and the loading conditions are always subject to a degree of uncertainty. Therefore, a reasonable assessment of the rock slope stability has to include the excavation of the multi-failure modes, the consideration of uncertainties of discontinuity characteristics, and the decision on stabilization measures with favorable cost conditions. This study was performed to provide a new numerical model of the deterministic analysis, reliability analysis, and reliability-based optimization for rock slope stability. The sensitivity analysis was carried out to verify proposed method and developed program; the parameters needed for sensitivity analysis are design variables, the variability of discontinuity properties (orientation and strength of discontinuities), the loading conditions, and rock slope geometry properties. The design variables to be optimized by the reliability-based optimization include the cutting angle, the support pressure, and the slope direction. The variability in orientations and friction angle of discontinuities, which can not be considered in the deterministic analysis, has a greatly influenced on the rock slope stability. The stability of rock slopes considering three basic failure modes is more influenced by the selection of slope direction than any other design variables. When either plane or wedge failure is dominant, the support system is more useful than the excavation as a stabilization method. However, the excavation method is more suitable when toppling failure is dominant. The case study shows that the developed reliability-based optimization model can reasonably assess the stability of rock slopes and reduce the construction cost.

개별요소법은 암석블록의 회전, 활동, 이탈 등과 같은 절리암반의 불연속 거동을 모델링할 수 있는 큰 장점을 가지고 있다. 그러나 불연속면의 분포특성에 해석결과가 매우 민감한데 비하여 현장조사에 의한 절리자료는 매우 부족하다. 또한 개별요소법에서 절리는 블록간의 접촉으로 고려되기 때문에 적절한 절리법칙의 적용은 절리암반의 안정성 평가에 매우 중요하다. 본 연구에서는 절리의 기하학적 특성과 역학적 특성을 고려한 개별요소해석을 수행하기 위하여 통계적 모델링 기법을 개발하였고 팽창성 암석절리법칙을 전산모델링 하였다. 통계적 모델링 기법은 부족한 현장 절리자료로부터 절리도를 재현함으로써 개별요소해석에 필요한 암석블록의 집합체를 제공한다. 또한 절리의 팽창성을 개별요소법의 변-변접촉에 도입함으로써 개별요소해석에서 절리면의 역학적 특성외에도 절리의 경계조건을 괴려할 수 있게 되었다. 통계적 개별요소모델을 위한 전처리 과정은 절리자료의 통계처리, 절리도 발생과 블록경계 발생으로 구성되며, 이 방법을 이용하여 절리의 기하학적 변수의 편차가 절리암반의 거동에 미치는 효과를 분석하였다. 통계적 모델링 기법은 해석자의 주관이 상당히 배제된 객관적인 해석을 수행할 수 있기 때문에 일관된 개별요소해석기법의 한 수단이 될 수 있다. 본 연구에서 적용한 팽창성 절리법칙은 절리의 전단거동과 수직거동간의 연성이 가능하며 실내시험에 의하여 필요한 입력변수를 정량적으로 결정하는 것이 용이하다. 단일절리에 대한 다양한 시험을 통하여 절리의 경계조건에 의해 영향을 받는 팽창성 절리의 거동특성을 분석하였다. 또한, 절리암반내 터널의 개별요소해석을 통하여 절리의 팽창특성이 터널의 안정성에 이바지함을 보였다.보품질로 측정하여 이들 요인이 EIP사용자의 직무성과에 미치는 영향에 관해 연구하였다. 본 논문은 EIP를 도입한 기업을 대상으로 EIP성과에 대한 연구를 진행하여 EIP를 도입하거나 구현중인 기업에게 적합한 경영관리적 방향을 제시할 수 있을 것이다.및 경험은 향후 상용설비를 위한 기본자료로 활용할 것이다.X>, 그리고 입원기간은 $21.6\pm14.3일(13\~56)$이었다. 수술 후 평균 CK-MB는 $11.3\pm14.1ng/mL$였다. 수술 후 조기 혈관 개존율은 $100\% (24/24)$였다. 모든 환자에서 완전 추적이 가능하였으며 평균 추적기간은 $20.4\pm15.2개월(5\~43)$이었다. 이 기간 중 사망환자나 흉통이 재발한 환자는 없었다. 걸론: 80세 이상 고령의 환자에서 OPCAB은 수술 후 합병증을 줄이고 좋은 결과를 보여 주었다. 그러므로 고령의 환자에서도 관상동맥우회술의 적응증이 되면 적극적으로 수술을 시행할 필요가 있으며, 수술방법은 OPCAB이 좋을 것으로 생각한다서 실용적 개발의 가능성을 보였다.에 따라 현저한 차이가 있었으며 Dimethoate처리$(30^{\circ}C,\; 0.2\%$액에서 24시간)에 의하여 볍씨의 호흡량이 감소되었다. 9) 산소호흡량과 평균발아소요일수와는 $\gamma=-0.945$로 부의 유의한 상관을 보였는데 산소호흡량이 많은 품종은 평균발아소요일수가 짧은 경향을 보였다. 10) 볍씨의 산소호흡량과 Dimethoate 처리에 의한 볍씨의 발아저해도와는 $\gamma=-0,771$의

The most widely accepted method for understanding the deformation mechanism of rock is from the use of computer simulation. However, if the changes in rock properties after excavation are significant this will prevent the computer simulation kent predicting the deformation with acceptable accuracy. If the deformations are, however, carefully measured in situ, the resulting data can be more useful far predicting the deformational behavior of underground openings, since the effect of the parameters which influence the deformational behavior are included in the measurement. In this study, extensive data analyses were carried out using the deformation measurements from the Waste Isolation Pilot Plant (WIPP), which is a permanent nuclear waste repository The results from computer simulations were compared with field measurements to evaluate the assumptions used in the computer simulations, For better description of the deformational behavior around underground excavations, several techniques were developed, namely: (a) the calculation of the zero strain boundary; (b) the evaluation of the influence of adjacent excavations on the deformational behavior of pre-excavated openings; (c) the description of the deformational behavior using in situ measurements; (d) the calculation of the shear stress distribution; and (e) the application of a Neural Network for the prediction of opening deformation.

Prediction of lining loads due to tunnelling is one of the major issues to be addressed in the design of a tunnel. The objective of this study is to investigate rational and realistic design loads on tunnel linings. factors influencing the lining load are summarized and discussed. The instruments for measuring the lining loads are reviewed and discussed because field measurements are often necessary to verify the design methods. Tunnel construction in the City of Edmonton has been very active for storm and sanitary purposes. Since the early 1970's, the city has also been developing an underground Light Rail Transit system. The load measurements obtained from these tunnels are compared with the results from the existing design methods. However, none of the existing methods are totally satisfactory, Therefore, there is some room for improvement in the prediction of lining loads. The convergence-confinement method is reviewed and applied to a case history of a tunnel in Edmonton. The convergence curves are obtained from 2-D finite element analyses using three different material models and theoretical equations. The limitation of the convergence-confinement method is discussed by comparing these curves with the field measurements. Three-dimensional finite element analyses are performed to gain a better understanding of stress and displacement behaviour near the tunnel face. An improved design method is proposed based on the review of existing design methods and the performance of numerical analyses. A specific method or combination of two different methods is suggested for the estimation of lining loads for different conditions of tunnelling. A method to determine the stress reduction factor is described. Typical values of dimensionless load factors nD/H for tunnels in Edmonton are obtained from parametric analyses. Finally, the loads calculated using the proposed method are compared with field measurements collected from various tunnels in terms of soil types and construction methods to verify the method. The proposed method gives a reasonable approximation of the lining loads. The proposed method is recommended as an approximate guideline for the design of tunnels, but the results should be confirmed by field measurements due to the uncertainties of the ground and lining properties and the construction procedures, This is the reason that in-situ monitoring should be an integral part of the design procedure.