The main consideration factor to design a magnetron of the sputtering system for TFT-LCD metallization is high sheet resistance (Rs) uniformity which is provided by the high target erosion and high current efficiency. The present study has developed a rectangular magnetron for TFT-LCD to bve considered full target erosion and high film uniformity. After an aluminum-2 at.% and alloy target was installed in a magnetron source and the film was deposited on the glass of 600${\times}$720 mm, the Rs uniformity of the deposited film was measured as functions of the magnet tilt and magnet scanning configuration. And the target erosion profile was observed with the target voltage. When sputtered at 4mtorr and 10kW, the magnet tilt for the high Rs uniformity of 8.38% was 7mm. The plasma voltage at the dwell home and end for full-face target erosion, when scanned the magnetron was 120% compared to the mean voltage of the other area.

We developed the experimental function (ERF) which can be used for the numerical curve fitting analysis in photoelectron spectroscopy (PES). We selected the core-levels of Ag 3d5/2 and Au 4f7/2 to obtain the ERF from the measured core-level spectra. For the numerical fourier transformation we applied the fast transform (FFT) algorithm. we considered optical (Wiener) filtering with the FFT due to noise and used Hann window function to remedy the information leakage in frequency domain due to discrete and finite sampling of measurement. The comparison of the curve fitting results using the ERF obtained in this work and the mathematical response function with a gaussian in the conventional approach shows clearly the improvement of the curve fitting analysis.

The real ($\varepsilon$1) and imaginary ($\varepsilon$2) parts of the dielectric function of ZnS have been measured by spectroscopic ellipsometry (SE) in the 3.7-6.0 eV photon-energy range at room temperature. The obtained dielectric function spectra reveal distinct structures at energies E0/(E0+$\Delta$0) and E1 critical points. The spectrum after chemical treatment to remove surface oxide overlayer showed that these data seem to be the best representation of the dielectric function of ZnS, having the largest $\varepsilon$2 value at E1 peak region reported so far by SE. Dielectric-related optical constants of ZnS, such as the complex refractive indices (n+n=ik), absorption coefficient, and reflectance, are also presented.

Possible role of hydrogen atoms on the formation of microcrystalline silicon films was schematically investigated using a plasma enhanced chemical vapor deposition system. A layer-by-layer technique that can alternate deposition of ${\alpha}$-Si thin film and then exposure of H2 plasma was used for this end. The experimental process was extensively carried out under different hydrogen plasma times (t2) at a fixed number of 20 cycles in the deposition. structural properties, such as crystalline volume fractions and grain shapes were analyzed by using a Raman spectroscopy and a scanning electron microscopy. Electrical transports were characterized by the temperature dependence of the dark conductivity that gives rise to the calculation of activation energy (Ea). Optical absorption was measured using an ultra violet spectrophotometer, resulting in the optical energy gap (Eopt). Our experimental results indicate that both of the hydrogen etching and the structural relaxation effects on the film surface seem to be responsible for the growth mechanism of the crystallites in the ${\mu}$c-si films.

Vertically well aligned multiwall carbon nanotubes were grown on nickel coated different substrates by plasma enhanced hot filament chemical vapor deposition at low temperatures below 650$^{\circ}C$. Acetylene and ammonia gas were used as the carbon source and a catalyst. The surface roughness of nickel layer increased as NH3 etching time increased. The diameters of the nanotubes decreased and the density of nanotubes increased as NH3 etching time increased. diameter of nanotube was 30 to 70 nm. Nickel cap was observed on the top of the grown nanotube and very thin carbon amorphous layer was fonde on the nickel cap.

PbTio3 is a promising material with perovskite structure for pyroelectric sensor applications with its superior pyroelectric properties, low dielectric constants, and low piezoelectric constants. Growth of pyroelectric thin films in general, needs relatively higher temperatures than those of conventional Si semiconductor processing However, low growth temperature is advantageous for the device integration. We report the low temperature (350$^{\circ}C$) growth of PbTio3 thin films by 3-gun DC magnetron reactive sputtering. The effects of substrate temperature, Pb-flux, and total pressure on crystalinity and preferred orientation of PbTio3 thin films are reported.

Paraelectric ZrTiO4 thin films were synthesized on a Si(100) substrate using DC magnetron reactive sputtering. Films deposited above-400$^{\circ}C$ exhibited crystalline characteristics. The dielectric constants ($\varepsilon$) and dielectric losses (tan$\delta$) of as-deposited and annealed films were measured in the 1 MHz range using a Pt upper electrode and a phosphorous-doped si bottom electrode. Preliminary data showed that as the deposition temperature increased, the dielectric losses decreased while the dielectric constants did not change significantly. similar trends for dielectric losses were observed when the as-deposited samples were annealed at 800$^{\circ}C$. The reduction of dielectric losses at high-deposition temperatures and post annealing correlated well with the x-ray diffraction peak widths.

We have setup a compact and useful in-situ SMOKE system in order to study surface magnetism of ultra-thin films. Since the longitudinal or polar magnetic fields can be applied to the sample by just rotating the sample manipulator, It is very simple to take hysteresis curve for in-plane or polar surface magnetism. The SMOKE system was tested by investigating the surface magnetism of ultra-thin Co film deposited on Pt(111) surface.

Hydrogen concentration depth profiles in homoepitaxial Si(001) films grown from hyper-thermal Si beams generated by ultrahigh vacuum (UHV) ion-beam sputtering have been measured by nuclear reaction analyses as a function of film growth temperature and deposition rate. Bulk H concentrations CH in the crystalline Si layers were found tio be below detection limits, 1${\times}$1019cm-3, with no indication of significant H surface segregation at the crystalline/amorphous interface region. This is quite different than the case for growth by molecular-beam epitaxy (MBE) where strong surface segregation was observed for similar deposition conditions with average CH values of 1${\times}$1020cm-3 in the amorphous overlayer. The markedly decreased H concentrations in the present experiments are due primarily to hydrogen desorption by incident hyperthermal Si atoms. Reduced H surface coverages during growth combined with collisionally-induced filling of interisland trenches and enhanced interlayer mass transport provide an increase in critical epitaxial thicknesses by up to an order of magnitude over previous MBE results.