In the present work, we investigated the photodissolution and photodiffusion effect on the interface of Ag/chalcogenide $As_{40}Ge_{10}Se_{15}S_{35}$ thin film by measuring the absorption coefficient, the optical density, the resistance change of Ag layer. It was found that the photodissolutioniphotodiffution ratio depends on the magnitude of photon energy absorbed in the chalcogenide thin film and the depth of photodiffution was proportional to the square root of the exposed time. Also, we have investigated the holographic grating formation with P-polarization states on chalcogenide $As_{40}Ge_{10}Se_{15}S_{35}$ thin film and $As_{40}Ge_{10}Se_{15}S_{35}/Ag$ double layer structure thin film. Holographic gratings have been formed using He-Ne laser (632.8 nm) which have a smaller energy than the optical energy gap, $E_g\;_{opt}$ of the film, i. e., an exposure of sub-bandgap light $(h{\upsilon} under P-polarization. As the results, we found that the diffraction efficiency on $As_{40}Ge_{10}Se_{15}S_{35}/Ag$ double layer structure thin film was more higher than that on single $As_{40}Ge_{10}Se_{15}S_{35}$ thin film. Also, we obtained that the maximum diffraction efficiency was 0.27 %, 1,000 sec on $As_{40}Ge_{10}Se_{15}S_{35}\;(1{\mu}m)/Ag$ (10 nm) double layer structure thin film by (P: P) polarized recording beam. It will offer lots of information for the photodoping mechanism and the analyses of chalcogenide thin films.

The effect of pressureless-sintered temperature on the densification behavior, mechanical and electrical properties of the $SiC-TiB_2$ electroconductive ceramic composites was investigated. The $SiC-TiB_2$ electroconductive ceramic composites were pressureless-sintered for 2 hours at temperatures in the range of $1,750{\sim}1,900[^{\circ}C]$, with an addition of 12[wt%] $Al_2O_3+Y_2O_3(6:4\;mixture\;of\;Al_2O_3\;and\;Y_2O_3)$ as a sintering aid. The relative density, flexural strength, vicker's hardness and fracture toughness showed the highest value of 84.92[%], 140[MPa], 4.07[GPa] and $3.13[MPa{\cdot}m^{1/2}]$ for $SiC-TiB_2$ composites of $1,900[^{\circ}C]$ sintering temperature at room temperature respectively. The electrical resistivity was measured by the Pauw method in the temperature ranges from $25[^{\circ}C]\;to\;700[^{\circ}C]$. The electrical resistivity showed the value of $5.51{\times}10^{-4},\;2.11{\times}10^{-3},\;7.91{\times}10^{-4}\;and\;6.91{\times}10^{-4}[\Omega{\cdot}cm]$ for ST1750, ST1800, ST1850 and ST1900 respectively at room temperature. The electrical resistivity of the composites was all PTCR(Positive Temperature Coefficient Resistivity). The resistance temperature coefficient showed the value of $3.116{\times}10^{-3},\;2.717{\times}10^{-3},\;2.939{\times}10^{-3},\;3.342{\times}10^{-3}/[^{\circ}C]$ for ST1750, ST1800, ST1850 and ST1900 respectively in the temperature ranges from $25[^{\circ}C]\;to\;700[^{\circ}C]$. It is assumed that because polycrystallines, such as recrystallized $SiC-TiB_2$ electroconductive ceramic composites, contain of porosity and In Situ $YAG(Al_5Y_3O_{12})$ crystal grain boundaries, their electrical conduction mechanism are complicated. In addition, because the condition of such grain boundaries due to $Al_2O_3+Y_2O_3$ additives widely varies with sintering temperature, electrical resistivity of the $SiC-TiB_2$ electroconductive ceramic composites with sintering temperature also varies with sintering condition. It is convinced that ${\beta}-SiC$ based electroconductive ceramic composites for heaters or ignitors can be manufactured by pressureless sintering.

Vanadium oxide thin films (VOx) have been deposited by RF magnetron sputtering from $V_2O_5$ target under different oxygen partial pressure ratios(0%, 10%) and substrate temperatures$(27^{\circ}C,\;400^{\circ}C)$. Crystallographic structure and morphology of the films are studied by XRD and SEM. Humidity-sensing properties of resistive sensors having interdigitated electrode structure are characterized through electrical conduction measurements. The films deposited at room temperature are amorphous whereas the ones deposited above foot are polycrystalline. The sensors show good response to humidity over 20%RH to 80%RH. Vanadium oxide thin films deposited with $0%O_2$ partial pressure at $400^{\circ}C$ exhibit greater sensitivity to humidity change than others.

The electric properties in YBCO superconductor was studied. In the measurement of current-voltage characteristics, a voltage across the superconducting sample was observed on applying an external magnetic field. The voltage increases with increase in applied magnetic flux, but it becomes constant at about $10^{-2}T$. The voltage continues to appear the removal of the magnetic field. The appearance of the voltage is ascribed to the trapping of magnetic flux. Depending on the direction of applied magnetic flux less than $2.5{\times}10^{-5}T$, the voltage in the magnetized sample increases or decreases.

This paper describes that the distribution of electromagnetic field occurred by PD(Partial Discharge) pulse was calculated with simulation program and characteristics of calibration and PD pulses measured with folded dipole types sensors were analyzed. As the distribution of electromagnetic field in simulation was very random the wide band measuring methods were good. Therefore three folded dipole antenna types sensors which had different their widths were designed and made. The signal according to direction and distance between sensor and pulse source in these sensor was measured and the spectrum of surface PD were acquired in the experiment of model transformer. In this result the characteristics of sensor which had middle width was better than others and the main spectrum of PD signals in surface discharge were existed in around 220MHz, 320MHz and from 450MHz to 750MHz.

A novel surface plasmon resonance(SPR) multisensing method, which does not require imaging apparatus such as CCD, has been proposed and implemented experimentally. The proposed method is based on the multichannel SPR and the separation of signals by use of additional layers whose thickness is controlled. SPR signals are influenced by the thickness of sensing layer as well as the optical condition of sensing surface. As the SPR signals from different ligands are usually positioned closely, the reflected light from sensing surface does not provide us with the clear differences of resonance signal depending on the kinds of ligands. It was found from our experiments that SPR signals from each ligand that is located on the additional layer with different thickness can be separated clearly enough to identify various signals from different ligands. Proposed method with theoretical design and simulation has been verified experimentally by using $SiO_2$ thin film layer as additional layer.

This paper deals with a new two dimensional clinometer based on dual axis micromachined accelerometers. The clinometer is a small and low-cost product, which is mainly developed to help golfers read easily the tilt of a putting green. First, this paper proposes the principle of two dimensional clinometer and also a calibration method with respect to the offset voltage and sensitivity of a accelerometer. Experimental results on the developed clinometer show that the proposed clinometer can provide useful information on the tilt angle and direction of an inclined plane.