Journal of the Korean Wood Science and Technology

  • 제50권4호
  • /
  • Pages.237-245
  • /
  • 2022
  • /
  • 1017-0715(pISSN)
  • /
  • 2233-7180(eISSN)
한국목재공학회 (The Korean Society of Wood Science & Technology)
권호 표지
DOI QR코드

DOI QR Code

Experimental Study of Bending and Bearing Strength of Parallel Strand Lumber (PSL) from Japanese Larch Veneer Strand

  • OH, Seichang (Department of Forest Resources, Daegu University)
  • 투고 : 2022.03.13
  • 심사 : 2022.05.24
  • 발행 : 2022.07.25
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

This study examined the structural performance of experimental parallel strand lumber (PSL) from a Larch veneer strand. The prototype of PSL from a Larch veneer strand was manufactured in the experimental laboratory and tested. The bending and dowel bearing strength were determined from the modulus of elasticity (MOE), modulus of rupture (MOR), and dowel bearing strength based on a 5% offset yield load. The test results indicated that the average MOR of PSL was higher than that of 2 × 4 dimension lumber, and the average MOE of PSL was lower than that of 2 × 4 dimension lumber. A linear relationship was observed between the MOR and MOE. The allowable bending stress of PSL was derived as specified in ASTM D2915 and compared with other research. The dowel bearing strength of PSL in parallel to the grain was approximately double that perpendicular to the grain of PSL. A comparison of several theoretical calculations based on each national code for the dowel bearing strength was conducted, and some theoretical equations produced results closer to the experimental results when it was parallel to the grain, but the difference was higher in the case perpendicular to the grain. The test results showed that PSL made with Japanese larch veneer strands appeared to be suitable for a raw material of structural composite lumber (SCL) appeared to be used as a raw material for SCL.

키워드

과제정보

This research was supported by Daegu University Research Grant 2018.

참고문헌

  1. Ahmad, M., Kamke, F.A. 2011. Properties of parallel strand lumber from Calcutta bamboo (Dendrocalamus strictus). Wood Science and Technology 45(1): 63-72. https://doi.org/10.1007/s00226-010-0308-8
  2. Ahn, K.S., Pang, S.J., Oh, J.K. 2021. Prediction of with-drawal resistance of single screw on Korean wood products. Journal of the Korean Wood Science and Technology 49(1): 93-102. https://doi.org/10.5658/WOOD.2021.49.1.93
  3. American Forest & Paper Association. 2012. National Design Specification for Wood Construction. ANSI/AF&PA NDS-2012. AFPA, Washington, DC, USA.
  4. APA-The Engineered Wood Association. 2007. Engineered Wood-Construction Guide. APA-The Engineered Wood Association, Tacoma, WA, USA. p. 29.
  5. Architectural Institute of Korea. 2015. Korea Building Code (in Korean). Architectural Institute of Korea, Seoul, Korea.
  6. Choi, G.W., Yang, S.M., Lee, H.J., Kim, J.H., Choi, K.H., Kang, S.G. 2020. A study on the block shear strength according to the layer composition of and adhesive type of Ply-Lam CLT. Journal of the Korean Wood Science and Technology 48(6): 791-806. https://doi.org/10.5658/WOOD.2020.48.6.791
  7. Choi, G.W., Yang, S.M., Lee, H.J., Kim, J.H., Choi, K.H., Kang, S.G. 2021. Evaluation of flexural performance according to the plywood bonding method of Ply-Lam CLT. Journal of the Korean Wood Science and Technology 49(2): 107-121. https://doi.org/10.5658/WOOD.2021.49.2.107
  8. Cui, Z., Tu, L., Xu, M., Chen, Z., Wang, C. 2020. The evaluation of dowel-bearing properties of laminated bamboo parallel to grain. Structures 25: 956-964. https://doi.org/10.1016/j.istruc.2020.04.004
  9. Fridiyanti, I., Massijaya, M.Y. 2018. Physical and mechanical properties of parallel strand lumber made from hot pre-pressed long strand oil palm trunk waste. IOP Conference Series: Earth and Environmental Science 141: 012007. https://doi.org/10.1088/1755-1315/141/1/012007
  10. Fujimoto, Y., Tanaka, H., Morita, H., Kang, S.G. 2021. Development of ply-lam composed of Japanese cypress laminae and Korean larch plywood. Journal of the Korean Wood Science and Technology 49(1): 57-66. https://doi.org/10.5658/WOOD.2021.49.1.57
  11. Gong, D.M., Shin, M.G., Lee, S.H., Byeon, H.S., Park, H.M. 2021. Dynamic property of cross-laminated woods made with temperate seven species. Journal of the Korean Wood Science and Technology 49(5): 504-513. https://doi.org/10.5658/WOOD.2021.49.5.504
  12. Han, Y., Kim, M.J., Lee, H.M., Kang, J.T., Eom, C.D. 2017. Comparison of cellular anatomical, physical and mechanical properties between Dahurian larch and Japanese larch. Journal of the Korean Wood Science and Technology 45(5): 525-534. https://doi.org/10.5658/WOOD.2017.45.5.525
  13. Hendrik, J., Hadi, Y.S., Massijaya, M.Y., Santoso, A., Pizzi, A. 2019. Properties of glued laminated timber made from fast-growing species with Mangium tannin and phenol resorcinol formaldehyde adhesives. Journal of the Korean Wood Science and Technology 47(3): 253-264. https://doi.org/10.5658/WOOD.2019.47.3.253
  14. Hwang, J.W., Oh, S.W. 2020. Mechanical performances of boards made from carbonized rice husk and sawdust: The effect of resin and sawdust addition ratio. Journal of the Korean Wood Science and Technology 48(5): 696-709. https://doi.org/10.5658/WOOD.2020.48.5.696
  15. Hwang, K., Komatsu, K. 2002. Bearing properties of engineered wood products I: Effects of dowel diameter and loading direction. Journal of Wood Science 48(4): 295-301. https://doi.org/10.1007/BF00831350
  16. Jang, S.S., Lee, H.W. 2019. Lateral resistance of CLT wall panels composed of square timber larch core and plywood cross bands. Journal of the Korean Wood Science and Technology 47(5): 547-556. https://doi.org/10.5658/wood.2019.47.5.547
  17. Kang, C.W., Jang, S.S., Kang, H.Y., Li, C. 2019. Sound absorption rate and sound transmission loss of CLT wall panels composed of larch square timber core and plywood cross band. Journal of the Korean Wood Science and Technology 47(1): 33-39. https://doi.org/10.5658/WOOD.2019.47.1.33
  18. Kim, C.K., Kim, K.M., Lee, S.J., Park, M.J. 2018. Change of bending properties of 2×4 larch lumber according to span length in the four point bending test. Journal of the Korean Wood Science and Technology 46(5): 486-496. https://doi.org/10.5658/WOOD.2018.46.5.486
  19. Kim, K.H., Hong, S.I. 2008. Bearing properties of domestic Larix glulam. Journal of the Korean Wood Science and Technology 36(4): 93-101.
  20. Korean Standard Association. 2016. Determination of Moisture Content of Wood. KS F 2199. Korean Standards Association, Seoul, Korea.
  21. Korean Standard Association. 2017. Method of Dowel-Bearing Strength Test for Wood and Wood-based Products. KS F 2156. Korean Standards Association, Seoul, Korea.
  22. Korean Standard Association. 2020. Method of Bending Test for Wood. KS F 2208. Korean Standards Association, Seoul, Korea.
  23. Kurt, R., Aslan, K., Cil, M., Cavus, V. 2012. Properties of parallel strand lumber from two hybrid poplar clones using melamine urea formaldehyde adhesive. BioResources 7(3): 3711-3719. https://doi.org/10.15376/biores.7.3.3711-3719
  24. Lee, I.H., Cho, S., Hong, S.I. 2018b. Prediction of the MOR of larch lumber. Journal of the Korean Wood Science and Technology 46(1): 93-99. https://doi.org/10.5658/WOOD.2018.46.1.93
  25. Lee, I.H., Pack, J., Song, D., Hong, S.I. 2018a. Longitudinal bonding strength performance evaluation of larch lumber. Journal of the Korean Wood Science and Technology 46(1): 85-92. https://doi.org/10.5658/WOOD.2018.46.1.85
  26. Li, X., Ashraf, M., Li, H., Zheng, X., Wang, H., Al-Deen, S., Hazell, P.J. 2019. An experimental investigation on parallel bamboo strand lumber specimens under quasi static and impact loading. Construction and Building Materials 228: 116724. https://doi.org/10.1016/j.conbuildmat.2019.116724
  27. Liu, Y., Lee, A.W.C. 2003. Selected properties of parallel strand lumber made from southern pine and yellow-poplar. Holzforschung 57(2): 207-212. https://doi.org/10.1515/hf.2003.030
  28. Park, H.J., Jo, S.U. 2020. Moisture absorption and desorption properties of Douglas fir, Hinoki, larch, plywood, and WML Board® in response to humidity variation. Journal of the Korean Wood Science and Technology 48(4): 488-502. https://doi.org/10.5658/WOOD.2020.48.4.488
  29. Park, H.M., Gong, D.M., Shin, M.G., Byeon, H.S. 2020. Bending creep properties of cross-laminated wood panels made with tropical hardwood and domestic temperate wood. Journal of the Korean Wood Science and Technology 48(5): 608-617. https://doi.org/10.5658/WOOD.2020.48.5.608
  30. Park, J., Song, Y., Hong, S. 2020. Bending creep of glulam and bolted glulam under changing relative humidity. Journal of the Korean Wood Science and Technology 48(5): 676-684. https://doi.org/10.5658/WOOD.2020.48.5.676
  31. Yang, S.M., Lee, H.H., Kang, S.G. 2021. Research trends in hybrid cross-laminated timber (CLT) to enhance the rolling shear strength of CLT. Journal of the Korean Wood Science and Technology 49(4): 336-359. https://doi.org/10.5658/WOOD.2021.49.4.336
  32. Yanti, H., Massijaya, M.Y., Cahyono, T.D., Novriyanti, E., Iswanto, A.H. 2019. Fundamental properties of composite board made with oriented strand board and three different species of veneer. Journal of the Korean Wood Science and Technology 47(2): 239-248. https://doi.org/10.5658/WOOD.2019.47.2.239
  33. Zhou, J., Huang, D., Song, Y., Ni, C. 2018. Experimental investigation on embedding strength perpendicular to grain of parallel strand bamboo. Advances in Materials Science and Engineering 2018: 3647395.